About the JBL P1024
Do you want maximum performance from your subwoofer? JBL puts Plus One technology to work in the Power Series P1024 10" sub a deeper cone and taller surround produces more effective cone area than on a standard 10" subwoofer, for more efficient operation and bigger bass output.
The P1024's high-tech cone combines Kevlar and paper into a combo that's strong, light, and ready to lay down the lows without distracting distortions. A sturdy die-cast frame and reinforced internal parts ensure reliability you can count on for the long haul.
Note: If you are wiring this DVC sub for lower impedance, make sure that your amp is compatible. Most 2-channel car amplifiers are stable down to 2 ohms in standard mode, or 4 ohms in bridged operation. Most mono amps are stable down to 2 ohms.
Priced per speaker
- 10" subwoofer with dual 4-ohm voice coils
- Kevlar-impregnated paper cone with Hi-roll rubber surround
- Plus One cone design for more effective surface area
- power range: 50-400 RMS watts (200 watts per coil)
- 1200 watts peak power handling
- frequency response: 25-500 Hz
- sensitivity: 92 dB
- mounting depth: 6-13/16"
- sealed box volume: 0.75 cu. ft.
- ported box volume: 1.25 cu. ft.
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # P1024
What's in the box:
- 10" Dual voice coil subwoofer
- Self-adhesive foam gasket
- Owner's Manual
- Technical Data sheet
- Warranty card
- JBL decal
JBL P1024 reviews
Thanks for submitting your review
More details on the JBL P1024
Features & specs
|Impedance||2 ohms or 8 ohms|
|Cone Material||Kevlar-impregnated paper|
|Ideal Sealed Box Volume (cubic feet)||0.75|
|Ideal Ported Box Volume (cubic feet)||1.25|
|Port diameter (inches)||3|
|Port length (inches)||8.625|
|Dual Voice Coil||Yes|
92 dB at 2.83 volts |
|Frequency Response||25 - 500 Hz|
|Max RMS Power Handling||400|
|Peak Power Handling (Watts)||1600|
|Top Mount Depth (inches)||6 13/16|
|Bottom Mount Depth (inches)||N/A|
|Cutout Diameter or Length (inches)||8 7/8|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Plus One Cone: The JBL Power Series subwoofers feature Plus One woofer cones. Each Power Series subwoofer features more cone area than comparable subwoofers of the same size. This increase in cone area means an audible increase in bass output and efficiency.
Woofer Materials: The woofer has a Kevlar-impregnated paper cone. This combination of materials has a high strength-to-weight ratio for higher sensitivity, and adds stiffness for a more accurate bass response.
Die-Cast Frame: The thick wall construction of the die-cast frame offers maximum rigidity to support the heavy motor structure of the speaker, and ensure the motor structure stays centered in the voice coil gap. The frame is fully vented to provide maximum movement of air behind the cone and spider.
Stitched-in Tinsel Leads: The tinsel leads are stitched into the spider in two places to greatly enhance reliability and eliminate audible tinsel lead slap.
Dual 4-ohm Voice Coils: For increased system flexibility, the woofer has two 3" 4-ohm voice coils. When the voice coils are wired in parallel with each other, the woofer presents a 2-ohm mono load. When the voice coils are wired in series with each other, the woofer presents an 8-ohm mono load. In addition, each voice coil may be connected to a different amplifier channel and each channel will see a 4-ohm load.
Recommended Sealed Box Volume: JBL recommends a 0.75 cu/ft sealed enclosure.
Recommended Ported Box Volume: JBL recommends a 1.25 cu/ft ported enclosure. One 3" diameter x 8-5/8" long port, tuned at 33Hz, should be used with the 1.25 cu/ft enclosure.
Recommended Bandpass Box Volume: JBL recommends a bandpass enclosure with a 0.75 cu/ft sealed rear chamber and a 1.25 cu/ft front ported chamber. One 4" diameter x 4" long port, tuned at 50Hz, should be used with this enclosure.
Power Handling: The woofer has two 4-ohm voice coils, and each voice coil can handle up to 200 watts RMS (800 watts peak).