About the Pioneer GM-A5702
Plays loud and clear
Plays loud and clear
Why put an amplifier in your car? Pioneer's GM-A5702 2-channel amplifier will greatly improve the sound quality in your vehicle, so you'll find yourself looking forward to your time on the road. This punchy Pioneer will power a pair of speakers with 150 watts RMS each, which is a gigantic jump over the power supplied by your car radio alone. You'll hear a lot more of the little details in your music, especially when you turn your system up to overcome road noise.
You can also put this versatile amp into single-channel mode, switch on the low-pass filter for clarity, and run a subwoofer with up to 480 watts RMS, perfect for some rockin' bass. A bass boost adds extra kick, if you want it. Speaker-level inputs allow you to add the GM-A5702 to a factory radio that doesn't have preamp outputs. If your vehicle needs a sonic upgrade, this amp's performance features and reasonable price make it a great choice.
- 2-channel car amplifier
- 150 watts RMS x 2 at 4 ohms (240 watts RMS x 2 at 2 ohms)
- 480 watts RMS x 1 in bridged mode (4-ohm stable in bridged mode)
- CEA-2006 compliant
- variable low-pass filter (40-500 Hz, 12 dB per octave)
- bass boost (0, 6, 12 dB at 50 Hz)
- preamp and speaker-level inputs
- fuse rating: 30A x 2
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 14"W x 2-3/8"H x 8-9/16"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # GM-A5702
What's in the box:
- 2-Channel amplifier
- Two 30A ATO fuses (installed)
- Speaker input harness with four 4" wires
- 4 Self-tapping screws (3/4" length)
- Owner's Manual (Eng/Fren)
- Owner's Manual (Span)
- Warranty sheet
Pioneer GM-A5702 reviews
Good overall amp for door speaker's. Skar TX series 5.25 up front and tx series 6.5s in the back. More than enough power.
1 of 1 found this helpful
I hooked it up three days ago .Amp gets hot. I have a 12" TS-W127M, 1300 WATT PIONEER SPK, AVH -110 BT PIONEER RECEIVER. BELIEVE I NEED TO UPGRADE MY Sounds good till it cuts off.
0 of 2 found this helpful
This is a very good Amplifier... Most of the negative to mediocre comments stem from being connected improperly. In bridge mode this amp is only 4 ohm stable.... Make sure you speaker configuration supports the amplifier specification. Load limit 4 ohm bridged and 2 ohm per channel.
3 of 4 found this helpful
Ran 4 gauge to it, Powers my 2 10"fosgate dvc @4 ohms bridged better than i anticipated, it cranks! Amp hardly gets warm to the touch. Great amp for the price.
3 of 3 found this helpful
If you're looking for an amp that has the physical appearance of a 1,000-watt RMS amp, but doesn't get too loud, this is amp for you! If you're looking for an amp that can power say two subwoofers, and you're good with 150 watts for each of them, this is the amp for you! On a good note this amplifier does amplify sound, but not that much. Also, when it's cold outside, this amp gets really hot within about two minutes of use to keep you warm on cold days; that's good right? ...Read the label. "1000W" does not equal 1,000 watts.
Pros: Amplifier does amplify sound.
Cons: "1000W" does not equal 1,000 watts.
6 of 31 found this helpful
Light weight, easy install, clear instructions, I have this powering a single 12" sub in a sealed enclosure, a separate Pioneer amp powering the components and a Pioneer Head unit, this replaces the factory Mach 460 system, this amp is perfect for this setup, thundering bass And I listen to all types of music, plenty of power for my sub.
Pros: Easy install, light weight, clear instructions, great power
Cons: None yet
7 of 7 found this helpful
It's powerful, to say the least. Pioneer products always have been, though.
2 of 5 found this helpful
sounds good, good value but gets hot
5 of 6 found this helpful
1 of 4 found this helpful
Super happy with my purchase would recommend this to someone who is looking to bridge their subs i have two JL 12W0-8 subs that are 8 ohms bridged them and they sound awesome has plenty of power and extra for the subs great job by crutchfield getting my order put fast and in awesome shape thanks!!
Pros: Powerful, doesnt get hot, easy to set up
8 of 8 found this helpful
This amp is powerful. As with just about all amps, you can't run it at 1 ohm bridged. So if your subwoofer is a Kicker 43CWR102, this is a dual 2 ohm sub. Which means you are running at 1 ohm. Its no wonder it gets hot. Incorrect usage like this will void the warranty. When using this amplifier in bridged mode, ensure you have a 4 ohm load and it will be fine.
Cons: No high pass x-over
13 of 13 found this helpful
Hooked this up to a Kicker 43cwr102 10" sub(400 watt rms) and ran the amp in mono at 480 watts rms and after about 5 minutes the amp was almost too hot to touch...would not recommend for any subs or systems that is going to push this amp...
Cons: gets extremely hot when pushed hard
12 of 22 found this helpful
Outstanding amp. Easy install. No problems
11 of 15 found this helpful
More details on the Pioneer GM-A5702
Features & specs
|RMS Power Output (Watts x Channels)||
150 x 2 |
|Peak Power Output (Watts x Channels)||---|
|Power at 2 Ohms (Watts x Channels)||240 x 2|
|Bridged Power (Watts x Channels)||480 x 1|
|Minimum Impedance Bridged||4|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||10-70k Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||75 dB|
|Low-Pass Crossover Frequency||40-500 Hz|
|Low-Pass Slope (dB/octave)||12 dB/octave|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0, +6, +12 dB|
|Bass Boost Frequency||50 Hz|
|Speaker Level Inputs||Harness|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4Ω load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 standards allow consumers to compare amplifiers on an equal basis. Using CEA-2006 criteria, the Pioneer GM-A5702 is rated at 150 watts RMS x 2 channels, with a 75 dBA signal to noise ratio.
Specifications: The manual also lists these non CEA-2006 compliant specifications:
- 2Ω: 240 watts x 2 channels (14.4 volts, 1 kHz, no more than 1% THD+N)
- Bridged: 480 watts x 1 channel (into 4Ω, 14.4 volts, 1 kHz, no more than 1% THD+N)
- Signal to Noise Ratio: 96 dB (at rated power)
Gain Control: To accommodate the varying range of signal levels coming from today's factory and aftermarket radios, the input gain is adjustable (0.3V-6.5V line level, 3V-26V speaker level).
LPF: A two position switch turns the low pass filter (LPF) on/off. The crossover point is variable between 40Hz and 500Hz, and the slope is 12dB/octave. You can adjust the crossover frequency via the provided rotary control.
Bass Boost: The GM-A5702 has a selectable bass boost at 50 Hz. You can set the boost at 0dB, +6dB, or +12dB.
Power Connections: The power and ground connections are 0.54" wide screw terminals, the remote turn-on screw terminal is 0.325" wide. A Phillips-head or flat blade screw driver (not included) is required to tighten/loosen the terminals. With a total fuse rating of 60 amps, 8 AWG power and ground wire is recommended. A 60A fuse should be placed on the power wire within 18" of the battery. Spade connectors are recommended for the power, ground, and remote wires.
Speaker Connections: The speaker screw terminals are 0.325" wide. A Phillips-head or flat blade screw driver (not included) is required to tighten/loosen the terminals. Spade connectors are recommended for the speaker wires.
RCA Input: The amplifier features one pair of stereo RCA line level inputs (left/right).
Speaker Input: The included speaker level input harness allows you to connect your OEM radio (or aftermarket radio that does not have the typical RCA-type outputs) without having to buy an adapter.
Auto Power On: When using the speaker level input, a circuit senses the input signal and turns the amp on automatically. This feature makes it easier to add an amplifier to a factory radio or to a receiver with no preamp outputs.
Fuse: The amp is protected by two 30-amp ATO blade fuses.
Q Crutchfield asked: Why did you buy this?
5 questions already asked