About the Pioneer FH-P8000BT
You'll enjoy the convenience of Bluetooth capability and wealth of playback options with Pioneer's FH-P8000BT CD receiver. And it fits perfectly in the double-size opening found in many dashboards.
This versatile receiver plays MP3, WMA, and AAC files on disc, controls a satellite radio tuner, and features a USB input, built-in iPod® controls, and a rear auxiliary input. When your iPod is connected to the USB input, the receiver bypasses your iPod's built-in digital-to-analog converter, using its high-quality DAC to deliver your music files with the highest fidelity possible. The Sound Retriever feature livens up flat-sounding music files by restoring information lost in compression, and you can use the 7-band equalizer to find the perfect tonal balance for your music. And you'll be able to make and receive calls through the stereo, without having to fumble around for your Bluetooth phone.
The receiver's clean design keeps operation refreshingly simple. The easy-to-use Rotary Commander interface locates your favorite songs or changes system settings with a touch of a button and a twist of the large control knob. System information, menus, and song titles show up bright and clear on the cool blue, 3-line LCD display. The 10-key wireless remote offers extensive fingertip control over your system while you drive, or you can add an optional adapter to control the receiver with your factory steering wheel controls.
Connect amplifiers and subwoofers to the three sets of high-voltage preamp outputs to build a high-powered car audio system. High-pass and low-pass filters let you adjust the range of frequencies you send to your speaker setup.
Want to keep your car's steering wheel audio controls?
In most vehicles, you can use an adapter to connect your vehicle's steering wheel controls to this stereo. Connect a few wires, then program the adapter for your particular car and the receiver, and you'll retain the convenience of your steering wheel controls. Check the "Accessories" tab for compatible adapters.
Bluetooth note: Use of this receiver's Bluetooth features will depend upon your phone's Bluetooth capabilities. Learn more in our article explaining Bluetooth profiles.
Note: If you're going to use your iPod with this receiver, be sure to check "Details" for specific iPod model compatibility with this receiver.
- CD receiver with built-in MOSFET amplifier (14 watts RMS CEA-2006/50 peak x 4 channels)
- plays CDs, CD-Rs, and CD-RWs, including discs loaded with MP3, WMA, and AAC files (will not play Digital Rights-protected music files)
- 3-line display with blue LCD display
- remote control
- Easy EQ 7-band equalizer with six preset tone settings
- Sound Retriever for improving sound of compressed music files
- low-pass (preamp outs) and high-pass (speaker and preamp outs) filters
- subwoofer level control
- Bluetooth built in
- built in iPod control no adapter necessary, but adding Pioneer's optional connecting cable lets you leave your iPod cable at home
- compatible with optional satellite radio, CD changer
- inputs: rear auxiliary input, rear USB input (for Windows Media devices, USB storage devices, and iPod)
- outputs: 6-channel, 4-volt preamp outputs (front, rear, subwoofer)
- compatible with most factory steering wheel audio controls (adapter required)
What's in the box:
- Double-DIN AM/FM/CD receiver
- Wiring harness
- Wireless Remote Control (CXC9115)
- CR2025 Lithium battery (installed in remote)
- Trim bezel
- 59" USB extension cable (has male Type A USB on one end and female Type A USB on the other end)
- Microphone with attached 13.25' cord (terminated into a right-angle 2.5mm sub-miniplug)
- Plastic visor clip for microphone
- Double-sided tape (1/2" x 7/8')
- 8 Pan-head ISO screws (M5 x 6mm)
- 8 Flat-head ISO screws (M5 x 6mm)
- Operation Manual on CD-ROM (English/French)
- Quick Start Guide (English)
- Quick Start Guide (French)
- Quick Start Guide (Spanish)
- Installation Manual (English/French)
- Warranty sheet (English/French)
- Information to User sheet
- Operating Environment sheet
- Warning sheet concerning installation safety
Pioneer FH-P8000BT reviews
Thanks for submitting your review
More details on the Pioneer FH-P8000BT
Features & specs
|Backup Camera Input||No|
|Second Camera Input||No|
|Android Control||USB MSC protocol + Bluetooth A2DP/AVRCP|
|Memory Card Slot||USB Memory|
|Satellite Radio Ready||Sirius or XM|
|RMS Power (CTA-2006)||14 watts|
|RMS Power (Manufacturer)||---|
|Peak Output||50 watts|
|RMS Power Bandwidth||20-20kHz|
|Sub Preamp Outputs||Yes|
|Switchable Rear Preamp Outputs||No|
|Navigation App Compatible (iOS)|
|Navigation App Compatible (Android)|
|Preamp Voltage||4 volts|
|Display Color||Organic EL|
|Key Button Color||Blue|
|Steering Wheel Control Compatible||Adapter required|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
|FM Sensitivity||8 dBf|
|Radio Data System||No|
|Music File Playback||MP3, WMA, AAC, WAV|
Overview: The Pioneer FH-P8000BT is a double-DIN, AM/FM/CD receiver that can also play MP3, WMA, WAV, and AAC files on disc as well. It has a rear panel 3.5mm auxiliary input for portable devices, as well as a rear panel USB 2.0 Full Speed input for your iPod or other USB-based portable audio player or USB memory device. The receiver also has built-in Bluetooth Wireless Technology for the playback of Bluetooth Audio devices and pairing with Bluetooth Telephones. Additional accessories that are compatible with this unit include XM or SIRIUS Satellite Radio (with an optional satellite radio tuner and antenna), and a multi-CD player. See section below on External Device Controls for details on compatibility.
Blue OEL Display: The FH-P8000BT features a black background with a three-line blue Organic ElectroLuminescent (Organic EL) display, which takes advantage of MP3, WMA, iPod, XM Radio, and Sirius, plus CD Text-encoded discs. This display makes it easy to read and cycle through the song title, artist, and other text used by these sources.
Ever Scroll: When the Ever Scroll feature is set to On, recorded text information scrolls continuously on the display. It will auto-scroll up to 64 characters. Set this feature to Off if you prefer the information to scroll only once.
Function Confirmation Tones: The receiver emits an audible beep tone each time a button is pressed. These function confirmation tones cannot be turned off.
Display Illumination/Clock Display: When the Clock Display has been turned on, pressing and holding the Source button turns off audio output, but the clock display remains on. When the Clock Display has been turned off, pressing and holding the source button turns the unit off completely. Even if you have turned the radio completely off you can view the clock display by pressing the clock button. The clock will then remain On until you turn it back Off. When the unit is On you can select between the clock display or the audio track/tuner display. When the unit is off but the ignition is on, the button illumination will light up when the vehicle's headlights are turned on.
Dimmer: To prevent the display from being too bright at night, the display is automatically dimmed when the car's headlights are turned on. You can turn the dimmer function On or Off. The orange/white illumination wire must be connected to the vehicle's headlight circuit in order for this feature to work.
CEA2006 Compliant: The power specifications for the FH-P8000BT are compliant with the CEA2006 Mobile Amplifier Power Testing and Measurement standards from the Consumer Electronics Association (CEA). These standards were developed as a way to equitably compare power specs from model to model and between manufacturers. The power output specs for the FH-P8000BT are as follows:
- CEA2006 Specs: 14 watts RMS x 4 channels (at 4 ohms, 20Hz-20kHz, 1% THD-N)
- Continuous Power Output: 22 watts RMS x 4 channels (at 4 ohms, 50Hz-15kHz, 5% THD)
- Maximum Power Output: 50 watts x 4 channels (or 50 watts x 2 channels at 4 ohms + 70 watts x 1 channel at 2 ohms for subwoofer)
MOSFET Amplifier: The FH-P8000BT is equipped with a MOSFET amplifier. Compared to conventional power supplies, the MOSFET amplification circuit is smaller and more efficient, and it delivers increased power with less distortion and absolutely zero on/off switching noise. More power means louder and cleaner music at higher volumes because you're not pushing the limits of the amplification circuit.
Advanced Sound Retriever: The Advanced Sound Retriever automatically enhances compressed audio and restores the original richness of the recording. When Advanced Sound Retriever is on, the high frequency range is compensated to match the frequency response curve to the original sound. There are two available levels of the Sound Retriever effect.
EEQ (Easy EQ): The FH-P8000BT is equipped with a 7-band parametric EQ with 7 preset EQ settings. You can boost or cut each frequency band by +/- 12dB at 2dB intervals. A Custom1 curve can be created for each source, while a Custom2 curve can be created that is common to all sources. Features of the Easy EQ include:
- Center Frequencies: 50, 125, 315, 800, 2k, 5k, and 12.5k Hz
- Preset EEQ Settings: Powerful, Super Bass, Vocal, Natural, Custom1, Custom2, and Flat
Selectable Loudness Levels: Loudness compensates for deficiencies in the low and high frequencies at low volumes. You can choose from three levels of loudness:
- Low: +3.5dB (100Hz), +3dB (10kHz)
- Mid: +10dB (100Hz), +6.5dB (10kHz)
- High: +11dB (100Hz), +11dB (10kHz)
Subwoofer Output: The unit has a pair of dedicated non-fading RCA subwoofer outputs with a low-pass filter, phase adjustment, and output level. When the subwoofer output is turned on, you can select the frequency of the 18dB/octave low pass filter (50, 63, 80, 100, or 125 Hz), select the subwoofer phase (normal/reverse), and the subwoofer gain (+6 to -24).
Switchable Rear Channel/Subwoofer Output: The rear speaker outputs can be set to provide full range output with full fading capability, or they can be set to provide non-fading subwoofer (low-pass) output. When the rear speaker outputs are set to subwoofer mode, the rear preamp outputs also switch from full range to subwoofer outputs. When set for subwoofer operation, you can connect the rear speaker leads directly to two small 4-ohm passive subwoofers or a dual voice coil sub with 4-ohm voice coils. If you prefer to use a single 2-ohm subwoofer, you can connect the woofer to one set of speaker leads, leaving the other set of rear leads disconnected. The maximum output provided when a 2-ohm load is connected to one set of leads is 70 watts.
High Pass Filter: If you do not want low frequency sounds to play from the front or rear speaker outputs, you can turn on the 12dB/octave High Pass Filter. The HPF has a selectable cutoff frequency (50, 63, 80, 100, or 125 Hz). Only frequencies higher than those in the selected range are output through the speakers.
Bass Boost: The Bass Boost function raises the level of sounds lower than 100Hz. You can select a desired level of bass boost between 0 and 6 (+12dB to 0dB).
Source Level Adjustment (SLA): This function lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. Settings are based on the volume level of the FM tuner, which remains unchanged. Each source can be independently adjusted from -4dB to +4dB.
Supertuner IIID AM/FM Tuner: The Supertuner IIID features Feed Forward Control, which avoids multi-path interference. This pre-detection of interference enables quick filter control and results in less distortion. In addition, the Supertuner IIID creates enhanced stereo during multi-path interference, unlike conventional tuners that collapse to mono. Digital processing reduces distortion, and improves Signal-to-Noise Ratio and stereo separation. Advanced analog technology improves signal processing sensitivity.
BSM (Best Stations Memory): The BSM (Best Stations Memory) function lets you automatically store the six strongest stations under preset buttons 1-6 of the currently tuned band. The tuner has 3 FM banks and 1 AM bank. You can store 6 presets for each bank giving you a total of 18 FM presets and 6 AM presets.
Local Tuning: Local seek tuning lets you tune in only those radio stations with sufficiently strong signals for good reception. There are 4 level of sensitivity for FM and two levels for AM. The higher settings allow reception of only the strongest stations, while lower settings let you receive progressively weaker stations.
Satellite Radio Ready: You can connect and control an external satellite radio tuner from XM or SIRIUS. The head unit is compatible with the GEX-P920XM (130P920XM, sold separately) Pioneer XM receiver. For Sirius there are two options; connect the SC-C1 SiriusConnect Universal Vehicle tuner and the CD-SB10 Pioneer Sirius Satellite Radio interface (700SIRPION, sold separately), or use the Pioneer Sirius Satellite Radio interface (130CDSB10, sold separately) and the SIRIUS dock-and-play adapter (607SCVDOC1, sold separately) along with a compatible portable SIRIUS radio. A subscription to XM or Sirius, plus the proper antenna is required in order to receive satellite radio programming. The satellite radio tuners connect via the IP-Bus connector on the back of the head unit.
Note: The unit will only display 8 characters at a time, and will scroll up to 16 characters.
MP3/WMA/WAV Playback: This unit can play MP3/WMA/WAV files recorded on CD-ROM, CD-R, and CD-RW discs in ISO9660 Level 1/Level 2, Joliet, and Romeo formats. MP3 files with a bit rate from 8-320 kbps, WMA files with a constant bit rate from 48-320 kbps, and WMA files with a variable bit rate from 48-384 kbps are supported. The unit is compatible with ID3 Tags and will display artist, folder, file, and album name, plus comments. Up to 8 directories, 99 folders and 999 files per disc are recognized by this unit.
AAC Decoding: This unit will playback AAC files encoded by iTunes recorded onto CDs, however files purchased from the iTunes Music Store (.m4p file extension) are not compatible. Tracks recorded at transmission rates of 16-320 kbps are playable on this unit.
List Button: The List button on the front panel allows you to the track title list, folder list, file list, preset channel list, or disc title list, depending upon the source. Once the List button is pressed, you can turn the multi-control knob to view each item on the list. To select the highlighted item, you can press the multi-control. This allows you to quickly make selections from most any source.
Disc Naming: You can use the disc title input feature to store up to 48 CD titles in the unit's memory. Each title can be up to 10 characters long.
iPod Interface: The FH-P8000BT can control and playback songs on an iPod. This unit supports only iPods with a standard Dock Connector. (Please see compatibility list below for your model and software version.) You can connect the iPod using the unit's USB input; a dock connector to USB cable, such as the one supplied with your iPod, or the optional 130CDIU50 (sold separately) is required. When connected via USB, you can choose to control the iPod from the head unit or the iPod itself (some iPods cannot be controlled in this manner). You can still change songs from the head unit, even when you are controlling the iPod manually. You can perform multiple search functions, including playlist, genre, artist, and album searches. While connected and the ignition switch is set to ACC or ON, the USB connection will power and charge your iPod. The Pioneer FH-P8000BT is "Made for iPod" compatible and supports the following iPod model functions (as of Dec. 2009):
|iPod/iPhone Model||Gen.||Software||Media Type||Control Type||Display Type||Charge|
|Audio||Video||head unit||iPod/iPhone||Song Info||Track Info|
| clickwheel |
Note: Apple iPod/iPhone software updates may change functionality results. If you download a newer software version, you may need to reset the head unit and your iPod/iPhone to regain functionality. If this doesn't work, you may need to revert to the older software version or wait until an newer software update is available.
USB Input: In addition to connecting an iPod, the rear panel USB input allows you to connect a USB portable audio player or USB flash memory that is USB Mass Storage Class compliant. USB Memory between 250MB and 250GB that are formatted in FAT32 or FAT16 are compatible.
Auxiliary Input: The FH-P8000BT is equipped with a rear panel 3.5mm stereo minijack auxiliary input for connecting external components, such as a portable MP3 player, DVD, or VCR. Once AUX 1 is selected as a source, you can change the source display of the input to any 10-character name. A second auxiliary device can be connected to this unit when an optional adapter is connected to the IP-Bus connector on the rear panel. Both Aux 1 and Aux 2 must be turned on in the setup menu in order to be selected as a source. See below for more information on the 2nd Auxiliary Input.
2nd Auxiliary Input Ready: In addition to the rear panel minijack Aux input (AUX 1), you can connect a second auxiliary component by connecting an IP-Bus/RCA connector. The CD-RB10 lets you connect one auxiliary component, and the CD-RB20 lets you connect an auxiliary component and a CD changer via the IP-Bus connector on the back of the head unit. The 10-character name of the connected auxiliary component can be entered into memory, and will appear as you cycle through the sources.
Bluetooth Solution: The FH-P8000BT is equipped with Pioneer's new Built-in Bluetooth Solution. You can make and receive phone calls wirelessly through the receiver. When you're not utilizing hands-free calling, you can use Bluetooth Wireless Technology to control and listen to a Bluetooth audio player.
Note: Not all Bluetooth-capable phones are compatible.
Microphone: During your wireless phone call, you can talk into the head unit's included microphone, and listen to the other party through the vehicle's speaker system. The microphone features a 13' cord that plugs into the back of the radio, and comes with an adjustable visor-mount clip.
Phone Pairing: Up to 3 Bluetooth-compatible cell phones can be registered to this head unit. You can transfer your entire phonebook at a single time to the head unit, which can memorize up to 3600 different numbers (400 persons x 3 contacts x 3 phone types).
Echo Cancellation: The receiver offers three levels of Advanced Echo Cancellation to keep phone calls sounding loud and clear.
Bluetooth Audio Players: In addition to supporting Bluetooth's Hands-Free Profile (HFP), the head unit also supports Bluetooth's wireless Audio Streaming Profile (A2DP) and Bluetooth's Audio Control Profile (AVRCP). These features allow you to wirelessly transmit music from your Bluetooth compatible cell-phone or portable audio player to the FH-P8000BT so you can listen to your stored music files through your vehicle's audio system.
Remote Control: The FH-P8000BT comes with a wireless remote control (CXC9115). The remote allows you to control the volume, switch between sources, pause the CD, change the display, and adjust the audio. The attenuator button allows you to quickly lower the volume by about 90%.
Steering Wheel Remote Compatibility: The head unit features an OEM steering wheel remote control input on the rear of the unit to allow you to keep your vehicle's radio steering wheel remote controls when used with the optional PAC SWI-RC Steering Wheel Control Interface Adapter (541SWIRC, sold separately); or the optional Metra ASWC Steering Wheel Control Interface Adapter (120ASWC, sold separately).
Note: Please consult the Crutchfield Car Selector to see if your vehicle is compatible.