About the Pioneer TS-D10LS4
Solid bass for a limited space
Solid bass for a limited space
Great bass is all about power, and Pioneer created their D-Series subs with that thought in mind. They built their D Series TS-D10LS4 10" shallow-mount subwoofer to handle up to 350 watts RMS, while it dishes out impressive low-frequency punch. This sub features an injection-molded polypropylene cone that's impregnated with Aramid fibers so it can handle heavy performance demands with precision. A butyl rubber surround supports the woofer during cone excursion so you'll get accurate, hard-hitting bass notes even when the music's turned up loud. And, with a mounting depth of only 3-5/16", this sub will fit into spaces regular subs can't.
Add some boom to your daily drive
If your vehicle's audio system is sounding a little anemic, this potent low-profile Pioneer sub can remedy that situation, bringing out all the power in your music by filling in the lowest frequencies. The 4-ohm impedance works great when you're bridging an amp or putting together a multi-sub setup. Power up one or two of these subs with a nice amp, and you'll understand that any kind of music is better with great bass.
- 10" 4-ohm subwoofer
- injection-molded polypropylene/aramid fiber cone
- butyl rubber surround
- stamped steel basket
- power handling: 350 watts RMS
- 1300 watts peak power handling
- frequency response: 20-3400 Hz
- sensitivity: 74 dB
- mounting depth: 3-5/16"
- grille not included
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # TS-D10LS4
What's in the box:
Pioneer TS-D10LS4 owner's manual
- One 10" Subwoofer
- Trim ring
- Six 1-1/8" Screws
- Adhesive backed foam gasket
- Manual (English/ German/ French/ Spanish/ Portuguese/ Italian/ Russian)
- Warranty information
Pioneer TS-D10LS4 reviews
Thanks for submitting your review
More details on the Pioneer TS-D10LS4
Features & specs
|Cone Material||Aramid Fiber interlaced IMPP|
|Surround Material||Butyl Rubber|
|Ideal Sealed Box Volume (cubic feet)||0.6|
|Ideal Ported Box Volume (cubic feet)||0.6|
|Port diameter (inches)||3|
|Port length (inches)||7.5|
|Dual Voice Coil||No|
76 dB at 1 watt |
|Frequency Response||20 - 3400 Hz|
|Max RMS Power Handling||350|
|Peak Power Handling (Watts)||1300|
|Top Mount Depth (inches)||3 5/16|
|Bottom Mount Depth (inches)||N/A|
|Cutout Diameter or Length (inches)||9 1/16|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Woofer Cone: Pioneer uses aramid fiber interlaced injection molded polypropylene (IMPP) for the cone, making it more rigid than polypropylene alone.
Terminals: The spring post terminals will accept pin connectors, single banana plugs, or bare wire up to 8 gauge.
Sealed Box Volume: Pioneer recommends a sealed enclosure with an internal volume between 0.35 ft³ and 0.7 ft³, with an ideal volume of 0.6 ft³. Sealed enclosures provide the most control over the woofer, will handle a lot of power, and provide accurate sonic reproduction, making them suitable to all types of music.
Ported Box Volume: The recommended ported box volume ranges from 0.5 ft³ to 0.7 ft³, with the ideal size being 0.6 ft³, using a single 3" diameter x 7½" long port. Ported (or vented) enclosures typically provide better overall efficiency than sealed, maximizing bass output for a given amplifier.
Measurements: When mounting the woofer without the trim ring, the dimensions change as follows:
- Mounting Height: 0.534"
- Flange Height: 0.2"
- Frame Diameter: 10.3"
I purchased this speaker to replace a factory subwoofer in my 2018 Lexus GX460. The speaker fit in the factory box perfectly. The only modification I had to make was drilling new holes for the screws. Very impressed with the sound and output!
mark de from ANKENY, IA