Contact us
Close contact box

JL Audio Slash 1200/1v3

Mono subwoofer amplifier — 1,200 watts RMS x 1

Item # 13612001V3

JL Audio's 1200/1v3 mono subwoofer amplifier puts out 1,200 watts RMS to your subs, so you'll enjoy...

JL Audio's 1200/1v3 mono subwoofer amplifier puts out 1,200 watts RMS to your subs, so you'll enjoy...

Need help?
Contact our Virginia-based experts.

Ships free

In stock

$1,449.99 -$279.12 Outlet savings


Other options

Add to wishlist

About the JL Audio Slash 1200/1v3

Pure power for your subs

JL Audio's 1200/1v3 mono subwoofer amplifier puts out 1,200 watts RMS to your subs, so you'll enjoy powerful, moving bass in your car. Its patented Class-D amp circuitry delivers exceptional, natural sound with extremely low distortion, while a parametric EQ bass boost give you precise control over your bass. You can add the RBC-1 wired remote (not included) to dial in the right amount of thump from the front seat.

Pure power for your subs

JL Audio's 1200/1v3 mono subwoofer amplifier puts out 1,200 watts RMS to your subs, so you'll enjoy powerful, moving bass in your car. Its patented Class-D amp circuitry delivers exceptional, natural sound with extremely low distortion, while a parametric EQ bass boost give you precise control over your bass. You can add the RBC-1 wired remote (not included) to dial in the right amount of thump from the front seat.

Consistent power for performance you can count on

This Slash v3 amplifier isn't just powerful, it's smart. As your car system's voltage fluctuates while you drive, the Regulated, Intelligent Power Supply™ system maintains steady, consistent power at any impedance between 1.5 and 4 ohms and at any voltage between 11 and 14.4 volts. You'll get all the power, all the time, even with a wide range of speaker combinations.

Minimize external noise

The 1200/1v3 uses "differential-balanced inputs" to isolate the signal's ground from the chassis ground, reducing noise and making this Slash v3 amplifier compatible with almost any system, including most factory radios. You can adjust the variable infra-sonic- and low-pass filters to maximize the performance of your subwoofers.

JL Audio 1200/1v3

Slash 1200/1v3 control and connection panel

Confused about impedance? Check out our article on matching subs and amps.


Product highlights:

  • mono subwoofer amplifier
  • 1,200 watts RMS x 1 at 1.5 to 4 ohms
  • Regulated, Intelligent Power Supply system
  • differential-balanced inputs
  • variable low-pass filter (40-200 Hz, 12 or 24 dB/octave)
  • parametric EQ bass boost (0-15 dB at 20-80 Hz)
  • variable infrasonic filter (15-60 Hz, 24 dB/octave)
  • optional wired remote bass boost
  • Class-D amplifier design
  • MOSFET power and output stages
  • preamp and speaker-level inputs (speaker-level input requires an optional adapter)
  • preamp outputs
  • 4-gauge power and ground leads and a 100-amp fuse recommended — wiring and hardware not included with amplifier
  • no onboard fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended
  • 19-3/4"W x 2-3/8"H x 9-7/8"D
  • warranty: 2 years
  • Our 60-day money-back guarantee
  • MFR # 98352

What's in the box:

  • Monoblock subwoofer amplifier
  • 2.5mm Allen wrench
  • Owner's manual

Scratch & Dent items may be missing non-essential accessories. In some cases the manufacturer's accessories have been replaced with generic equivalents.

Customer reviews

Loading reviews...

JL Audio Slash 1200/1v3 reviews

Average review:

5 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

JL Audio Slash 1200/1v3

rajwinder from Milwaukee, WI on 2/14/2019

Verified customer (What's this?)
Verified employee purchase (What's this?)

the best of best amplifier I have owned nothing better than this



Crutchfield response on

1 of 2 found this helpful

JL Audio 1200/1v3

Bryan from South Dakota on 12/21/2017

Verified customer (What's this?)
Verified employee purchase (What's this?)

Highly disappointed. Had two extra batteries along with the two in the truck with a huge alternator and hands continue to shut down. For the money there is a lot better amps out there 5 times the size of this for the same money



Crutchfield response on

2 of 23 found this helpful

JL Audio Slash 1200/1v3

Desmond from California on 2/26/2017

Verified customer (What's this?)
Verified employee purchase (What's this?)

I have a srt8 charger and I've been threw servant amps trying to find that perfect sound. I tested the xd1000/1v2 awesome amp even running it at 4ohms it's underrated was doing around 700 watts rms. Then I ran up on the 1200/1v3 a real game changer. The difference in the quality and clarity are like night and day. This amp is also underrated like 1500 watts easy. I had a 2004 kicker kx1200.1 running at 1ohm 1486watts rms. Then I bought the jl amd it's stronger than my old kicker faithful amp. I'm running the amp at 4ohms amazing and the gain is at 50% with proper tuning. My cvx 12 are being abused by this amp after 1hr of playing I smelled the voice coils smh but I have 2 cvx 15s en route and this will be very very brutal can't wait. I have the 1200/v3 paired with the xd800/8v2 amd they are outstanding. I have a optima red top battery amd a stinger hybrid 5 farid capictor and so far no issues looking to do a big 3 upgrade before I install the cvx 15's great job JL I'm a JL for life now. For the record I have owned hifonics,kicker,rockford,alpine,pioneer,massive audio,cadence, but JL is in a different stratosphere.

Pros: Excellent quality components, very well built.

Cons: Priced high but you get what you pay for.

Crutchfield response on

13 of 16 found this helpful

Powerful With An Array Of Fine Tuning Options & Features

Jason from Tampa, FL on 10/1/2014

Verified customer (What's this?)
Verified employee purchase (What's this?)

Without a doubt, one of the finest subwoofer amplifiers I have ever owned. I'm sure the up front price will cause a lot of average consumers to shy away, but this is a case of truly getting what you pay for. As head units become more and more simplified and lose features (fully active crossovers, etc.) it's nice to have a solid subwoofer amp that can be dialed in precisely. Also, to the other reviewer who blew a fuse at the distribution block? You might want to re-check your power wire and setup. I've been running my amp for just over a year with a overall 150AMP fuse near the battery, and another 100AMP fuse about 12 inches away from the amp itself, and have never had a single problem with fuses blowing. This amp originally powered two 12w6v3 subs, and everything sounded absolutely incredible. I've since gone to a more "compact" setup comprised of a single Fi Q 12" sub in a sealed enclosure, and it sounds stellar. If you have the cash to pony up for this amplifier, you won't be disappointed. As consumer electronics get cheaper and cheaper, it's nice to have an amp like this made of top-shelf components.

Pros: Clean Power, Precise Crossover Adjustments, Powerful Bass EQ and Q Features

Cons: Price, Size

Crutchfield response on

18 of 19 found this helpful


Matt from Albuquerque on 4/11/2013

Verified customer (What's this?)
Verified employee purchase (What's this?)

I have this amp with two new JL W6v3 12" subs and I haven't even turned the sensitivity up due to the fact that I'm breaking in the subs, and my lights are dimming down to almost off and I blew the distribution block 100amp fuse. I'm definitely gonna have to get a better battery and new alternator. Just an amazing amount of power.

Pros: Everything!

Cons: Nothing! Besides your probably gonna have to get an alternator and deep cycle battery.

Crutchfield response on

23 of 28 found this helpful

Verified customer (What's this?)
Verified employee purchase (What's this?)



Crutchfield response

<< >>

Product Research



Mono Subwoofer Amplifier: The JL Audio 1200/1v3 is a class D monoblock subwoofer amplifier. With its regulated power supply, the rated output is 1,200 Watts RMS x 1-channel into a load of 1.5Ω to 4Ω, with an input voltage of 11V to 14.5V. The signal to noise ratio is >95 dB and a total harmonic distortion is <0.05%, both measured at rated power (1,200 watts RMS). The amplifier's frequency response is 5-250Hz. (It is not designed for driving full range speakers.)

R.I.P.S. (Regulated Intelligent Power Supply): The JL Audio R.I.P.S. system ensures consistent power delivery over a wide range of battery voltages and load impedances, providing the rated power output at any impedance from 1.5Ω to 4Ω and at any vehicle voltage from 11V to 14.5V.

  • Regulated Power Supply: The power supply adjusts to maintain the amplifier's rated power output and low distortion operation over a wide range of vehicle voltages (11V-14.5V), so the amplifier's output remains stable in real-world car audio situations.
  • Intelligent Power Supply: An Intelligent circuit monitors output current to optimize the amplifier's output power over a wide range of load impedances (1.5Ω to 4Ω). The R.I.P.S. System detects the actual load impedance, rather than relying on often inaccurate assumptions based on a speaker's rated impedance, and adjusts output rail voltages to deliver consistent output.

RealSink Heat Management: This Slash v3 amplifier features a real cast-alloy heat sink with vertically-oriented fins, very effective at dissipating heat from the amplifier via convection and radiation. This design is achieved through extensive finite-element analysis, resulting in an amplifier that keeps cool under the most demanding conditions. As an added cosmetic benefit, the cast-aluminum end-caps replicate half of a heat sink fin so that when two or more amplifiers are mounted end-to-end, you get a seamless custom look.

Advanced Rollback Protection: If a Slash v3 amplifier should ever reach an unsafe temperature, the Advanced Rollback Protection circuit reduces power until the amplifier cools down, without turning the music off completely.

Class D Circuitry: JL Audio's Patented Class D output circuit utilizes a discrete control section and a unique feedback loop design, resulting in a damping factor greater than 500 at 4Ω (>250 at 2Ω), higher than most other Class D and Class A/B designs. The benefit is tight, clean bass reproduction with the efficiency advantage of Class D.

Differential-Balance Inputs: The 1200/1v3 features differential-balanced input architecture to reject noise and ensure compatibility with a wide variety of source units, including many OEM systems. Without using a line output converter, you can connect most OEM or aftermarket source units to the amplifier without creating any noise or compatibility issues.

Note: You will need a speaker wire to RCA adaptor (item number 136XDCLR2S, sold separately) when using a speaker-level input.

Preamp Outputs: The preamp outputs make connecting multiple amplifiers simple. The 1200/1v3 features an independent crossover for the preamp output with frequency (40-200 Hz), mode (Full Range, LP, or HP) and slope (12 or 24 dB) adjustments.

Protection Circuitry With Status Indicator Lights: There are four status indicator lights on the top of the amplifier:

  • Power (Green): green LED indicates the amplifier is turned on and operating normally
  • Thermal (Red): red LED indicates the amplifier has exceeded its safe operating temperature; the power output is reduced until the heat sink temperature drops back to a safe level
  • Low Ω (Amber): amber LED indicates the impedance of the connected speaker(s) is lower than the optimum impedance range for the amplifier and the power output is reduced; the amber LED can also indicate a short in the speaker wire
  • Low V (Blue): blue LED indicates a drop in supply voltage below 8 volts; the LED will remain lit longer than the duration of the voltage drop to alert you to the problem; in this situation the amplifier will also shutdown (and the green LED turns off); once the voltage rises above 9 volts, the amplifier will turn itself back on

Infrasonic Filter: Ultra-low frequencies that cannot be reproduced by a subwoofer do not become sound, but unnecessary oscillations which affect sound by causing distortion. These frequencies also waste amplifier power and can cause damage to speakers. Using the infrasonic filter, variable from 15 Hz to 60Hz, removes the signal below the setting to improve the performance of the speakers by eliminating harmful distortion. The infrasonic filter can be turned off.


Simplified Gain Setting: The amplifier's R.I.P.S. feature allows easy gain setup. Because the amplifier always delivers the same output power within its operational range of load impedance and power supply voltage, the maximum, unclipped output is predictable. This makes setting input gain very simple; you'll need a Digital AC Voltmeter (sold separately) and a CD with a sine-wave bass test tone recorded at 0 dB reference level (item number 503CD104, sold separately). In addition to the continuously variable rotary gain control, the Input Voltage switch adjusts the gain range, set to Low (200mV-2V) or High (800mV-8V).

Low Pass Crossover: The built-in crossover allows you to adjust the frequency and filter slope of the amplifier's powered output:

  • Mode/Slope Switch:
    • Off: crossover is bypassed, useful when using an external crossover; in this position the Advanced Bass Control is defeated
    • 12 dB: filter slope is 12 dB/octave, often used when the subwoofer is in the trunk of a sedan
    • 24 dB: filter slope is 24 dB/octave
  • Frequency: crossover frequency variable from 40 Hz to 200 Hz; the detented potentiometer allows accurate adjustment

Preamp Output Crossover: An independent crossover address what frequencies the preamp outputs will pass:

  • Output Mode:
    • Full Range: the preamp output is the same as the amplifier's input; the signal is not affected by the Advanced Bass Control
    • Amp Filter: the preamp output signal is the same as the amplifier's powered output, governed by the Low Pass Crossover and Advanced Bass Control
    • Out Filter: the independent crossover controls affect the preamp output:
      • Filter Slope: 12 dB/octave or 24 dB/octave
      • Filter Mode: Low Pass or High Pass
      • Filter Frequency: crossover frequency variable from 40 Hz to 200 Hz; the detented potentiometer allows accurate adjustment

Advanced Bass Controls: The bass control functions on the amplifier include:

  • Variable Bass Boost: The amplifier's variable bass boost features a single band parametric equalizer with variable Q (0.5 - 4.3), center frequency (20 Hz to 80 Hz), and boost (0 to +15dB).
  • Infrasonic Filter: The 24dB/octave infrasonic filter has a variable crossover point (15 Hz to 60 Hz). The infrasonic filter can be turned off.
  • Remote Bass Port: The amplifier is equipped with a connection for an optional wired Remote Bass Control (item number 136RBC1, sold separately), allowing boost control from the front of your vehicle.

Output Polarity: Depending on the distance between the mid-bass speakers and the subwoofer in your system, it might be preferable to reverse the polarity of the subwoofer to produce a better transition between the two. The Output Polarity switch allows you to quickly reverse the subwoofer's polarity (0°/180°).


Power and Ground: The amplifier's set-screw Power and Ground connections accept up to 4-gauge wire (4-gauge minimum is recommended).

Note: The Amplifier is not equipped with a fuse. An external 100-amp fuse (not included) must be installed on the power wire. If the system has only this amp and a wiring kit is used that includes a fuse with a value other than 100-amps, the original should be replaced with a 100-amp fuse.

Speaker Output Terminals: The two pair of set-screw speaker terminals accept 12-gauge to 8-gauge wire. The terminals are internally shorted together, making it easy to connect two subwoofers.

Remote Turn-On: The set-screw turn-on lead terminal will accept 12-gauge to 8-gauge wire.

Note: If your headunit does not have a dedicated remote turn-on output, the amplifier's turn-on lead can be connected to a switched +12V volt circuit.

Preamp Inputs: The amplifier features one set of differential-balanced RCA inputs. The amplifier's input level can be set to Low (200mV-2V RMS) when connecting the amplifier to a low-level preamp signal or set to High (800mV-8V RMS) when connecting the amplifier to a higher voltage preamp or speaker-level signal.

Preamp Outputs: The amplifier also features one set of preamp outputs so you can send audio to another amplifier in your system. The preamp output can be full range, or the built-in crossover can be applied.

Note: All inputs, outputs and controls are located on the front side of the amplifier to make installation simple and neat.

Loading accessories...

Customer Q&A

Crutchfield asked: Why did you buy this?
Good [ Armando  Jul 09, 2019 ]
best performing sub amplifier available [ Jeremy  Jan 14, 2017 ]
I had the 1000/1v2 for 8 years and never had a problem with it. Paired with 12w7 and the sound was amazing! Going to pair this one with a 13w7. [ Ron  Dec 24, 2016 ]

Loading articles...