Chat
Contact us
Close contact box
Connect ID #
428 756 563 3
Connect ID #
428 756 563 3
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

Our contact center is currently closed.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

JL Audio JD1000/1

JD Series mono subwoofer amplifier — 1,000 watts RMS x 1 at 2 ohms

Item # 13698363

We think JL Audio's JD Series amplifiers will provide tremendous performance and value for our customers.

Find what Fits your car

We think JL Audio's JD Series amplifiers will provide tremendous performance and value for our customers.

Ships free

Temporarily out of stock

Expected: 11/30/2020

$389.99

Other options

About the JL Audio JD1000/1

Power up the bass

JL Audio's JX Series amplifiers were very popular with our customers, garnishing rave reviews citing their tremendous performance and value. We think their latest JD Series amps will follow in their footsteps, offering superior power and serious features for your dollar. The JD1000/1 mono subwoofer amplifier will send up to 1,000 watts RMS to a sub, so you'll hear and feel the bass roaring like thunder. A variable low-pass filter and bass boost help you tune your sub to fit your system and sound its best. An optional wired remote control lets you turn the sub up or down from the front seat.

Power up the bass

JL Audio's JX Series amplifiers were very popular with our customers, garnishing rave reviews citing their tremendous performance and value. We think their latest JD Series amps will follow in their footsteps, offering superior power and serious features for your dollar. The JD1000/1 mono subwoofer amplifier will send up to 1,000 watts RMS to a sub, so you'll hear and feel the bass roaring like thunder. A variable low-pass filter and bass boost help you tune your sub to fit your system and sound its best. An optional wired remote control lets you turn the sub up or down from the front seat.

Connection features

The amp includes speaker-level inputs with signal-sensing amp turn-on, along with preamp inputs and outputs, so it's ready to work in virtually any system. Differential-balanced inputs plus JL Audio's NexD™ amp technology keep the signal sounding pure and noise-free at all times.

JL Audio JD1000/1

JD1000/1 connection and control panel

READ LESS

Product highlights:

  • mono subwoofer amplifier
    • 600 watts RMS x 1 at 4 ohms
    • 1000 watts RMS x 1 at 2 ohms
  • Class D amp design with NexD™ switching technology
  • frequency response: 7-500 Hz
  • variable low-pass filter (50-500 Hz, 12 dB/octave)
  • variable bass boost (0-12 dB at 45 Hz)
More Info:

What's in the box:

  • Monoblock subwoofer amplifier
  • 2.5mm Hex key
  • 3mm Hex key
  • Owner's manual

Customer reviews

Loading reviews...

JL Audio JD1000/1 reviews

Average review:

13 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

More details on the JL Audio JD1000/1

Mark G.

Product Research

Features

Amplifier Power Ratings:

  • At 14.4 volts: >80 dB S/N, 1% THD+N
    • 4Ω: 600 watts RMS
    • 3Ω: 800 watts RMS
    • 2Ω: 1,000 watts RMS
  • At 12.5 volts: >80 dB S/N, 1% THD+N
    • 4Ω: 500 watts RMS
    • 3Ω: 650 watts RMS
    • 2Ω: 800 watts RMS

Clipping LED: Using a 50 Hz sine-wave test tone recorded at 0 dB reference level (not included), the clipping LED helps you set the gain control to the maximum unclipped level.

Low Pass Crossover: The 12dB/octave low-pass filter is always engaged; it cannot be bypassed. The crossover point is continuously variable from 50-500 Hz.

Bass Boost: The bass boost circuit is variable from 0 to +12dB. The boost is centered at 45Hz.

Protection Circuitry: The JD1000/1's protection circuitry automatically turns the amplifier off if thermal limits are exceeded, a short circuit is detected in the speaker wiring, or the input voltage drops below 11 volts.

Wired Remote: An optional RBC-1 Remote Level Control (sold separately) can be added, allowing you to adjust the amp's output level from the front of the vehicle.

Controls:

  • Input Sensitivity: rotary control; used to match your source unit's output voltage to the input stage of the amplifier for maximum clean output; the range of the dial depends on how the Input Voltage switch is set
  • Input Voltage: 2-position switch:
    • Low: input sensitivity control (gain) range is 200mV-2V; used with the preamp output of typical aftermarket radios
    • High: input sensitivity control (gain) range is 800mV-8V; used with speaker level outputs and high output preamps
  • Low Pass Crossover Frequency: rotary control; continuously variable from 50-500 Hz
  • Turn-on Mode: 3-position switch:
    • Remote: use when the source unit has a +12 volt remote turn-on wire (preferred method)
    • Offset: the amp reads a small DC signal typical on the speaker level output of factory radios (senses the offset on the left input)
    • Signal: detects a midrange speaker level signal on the input; turns off after approximately 30 seconds with no signal
  • Bass Boost: rotary control; continuously variable from 0 to +12 dB

Connections:

  • Power: The power, ground, and remote turn-on connections are set-screw terminals:
    • Power and Ground: accept up to 4-gauge wire (4-gauge minimum recommended); the included 3mm hex key is used to tighten/loosen the set-screws
    • Remote Turn-on: accepts up to 10-gauge wire (18-gauge minimum recommended); the included 2.5mm hex key is used to tighten/loosen the set-screw
Note: The amplifier is not equipped with a fuse. An external 80-amp fuse (not included) must be installed on the power wire. If a wiring kit is used which includes a fuse with a value other than 80-amps, the original should be replaced with an 80-amp fuse.
  • Subwoofer Output Terminals: The subwoofer outputs are set-screw terminals. They accept up to 8-gauge wire (16-gauge minimum recommended). There are two pair of outputs, internally wired in parallel, making it easy to connect two subwoofers. The included 2.5mm hex key is used to tighten/loosen the set-screws.
  • Signal Inputs: The stereo RCA input jacks accept either preamp or speaker level signals. When connecting speaker level signals, a speaker wire to RCA adapter is useful. The left and right channels are internally summed to mono.
  • Preamp Outputs: The stereo RCA preamp outputs pass the signal connected to the RCA inputs, so another amplifier can be added easily. The output is not affected by the JD1000/1's gain, crossover, or bass boost controls. The preamp output signal is buffered to prevent noise.

Note: When the input voltage switch is set to Low, the voltage of the RCA output matches the input; when set to High, the output voltage is attenuated -12 dB.

  • Remote Level Control: The RJ-25 connection is used for the optional optional RBC-1 wired remote.

Loading accessories...

Customer Q&A

6 questions already asked

Q
Could I pair this with a JL 12W7 3ohm comfortably?
[ HJLCx2  Jun 16, 2020 ]
2 answers
A
I'm no pro, but this would power that sub. I'd say it's a good match. Shouldn't be too much to overload the driver.
[ NATHANAEL  Jun 17, 2020 ]
A
Hi, I can't answer your question with certainty because I still have not hooked my gear up because of back ordered parts. However, I did research your sub and if it were me, I think I would go with the JL HD1200/1 or the JL1200/1v3 being that your sub can handle up to 2000 watts peak. Sounds to me like you want big bass, and I would go big or go home. Plus these two amps handle 1.5 to 4 ohms!!!! Just my opinion.
[ BENNY  Jun 17, 2020 ]
Q
How would this pair with 2 x JL Audio 10TW3-D4s?
[ Robert  May 25, 2020 ]
2 answers
A
I have this amp paired with a steal box which has 2 of these 10s and i couldn't be happier. Sounds great
[ TONY  May 26, 2020 ]
A
Ofcourse with JL you get the best.. The JD1000/1 has plenty of power. Paired with those subs, your not gonna find a better sound anywhere else. The sub has a very tight, clean bass. I run them both my boat and my truck. You will not be disappointed.
[ NICK  May 25, 2020 ]
Q
Does this come with the bass knob included?
[ Joel  May 11, 2020 ]
2 answers
A
Hi Joel, the JL Audio JD1000/1 amplifier does not come with a remote bass knob. You would need to make a separate purchase of the JL Audio RBC-1 remote to use with this amp.
[ Jess  Jun 01, 2020 ]  Staff
A
No you have to buy it separately.
[ JAMES  May 28, 2020 ]
SHOW MORESHOW LESS

Loading articles...

TOP