Worth your funds

Pretty good stuff. Could be sturdier but it works especially for the money. As described. Would buy again

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Fit perfectly

Have questions for
?

Perfect fit, moderatly difficult install

Worked perfectly but attaching the speaker to the mount requires some finess.

Have questions for
?

Need these for an easier install

Crutchfield is the best online audio spot on the planet.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Works fine.

Have questions for
?

Simplified install

Fit fine quality ok.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

These worked great for the front doors of my '09 Ridgeline. The rear doors...not so much. The surface area around the speaker cutout is not as flat as on the front doors. I had to trim the upper right screw hole tab nearly off and the one at the bottom came to rest on a angled/rounded surface. A center punch made it possible to get a drill bit or self tapping screw started. Not really a complaint....just a heads up. I will never buy car stereo gear anywhere else. Crutchfield makes the work easier with the provided car documentation, wire harness adapters and speaker mounting brackets.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Makes install easy

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

It was nice that they fit the stock mounts. I did have to drill new holes, but it wasnt hard.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Very fast delivery. Quality product.

Have questions for
?

Gen 1 Ridgeline Speakers

Perfect fit, simple, easy to install, and great price point. A must for the Honda Ridgeline.

Have questions for
?

Gets the job done, but that's it

nothing. Work, but they're flimsy and it is pretty easy to over-nighter your screws and strip the holes. I recommend using very corse screws to install your speaker to the adapter.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Made installing speakers a breeze; just knock off some tabs and they were ready to go. Less than 10 minutes a door. Just an fyi, make sure you pre-drill holes, you don't want to ruin your new speakers.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Very easy to use...

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

These mounting brackets made replacing my old stock speakers easy. 07 Honda Ridgeline.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Easy install

Have questions for
?

2010 Honda Ridgeline

The mounting brackets worked great for the front doors but I had to cut two of the three tabs for the rear doors.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Made install easy

Have questions for
?

Good but with modifications to fit 6.5" speakers

Fit but needed to be modified to work with 6.5" speakers. Would have helped if there was information with these to let me know it was okay to modify.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

I had to do some minor modifications for them to fit on the rear doors of my ridgeline. They fit perfect in the front doors

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

These brackets worked for my front and rear doors of my Honda Ridgeline. It matched the front door perfectly. The rear door was close to perfect

Have questions for
?

Added installation steps

Depending on the size of speakers you're installing, these brackets can be kind of a pain. There are tabs that face inwards which need to be snapped off if the speaker doesn't sit flush. They do no always break off clean, so the inner diameter of the speaker mount might have jagged edges. I filed the edges smooth which added to the installation time. Not a huge deal, but something to be aware of.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

These, and the instructions provided by Crutchfield, made my speaker installation incredibly easy.

Have questions for
?

Almost good...

The Scosche SAHR6 Speaker Mounting Brackets claim to fit 6 3/4" speakers, however, at least with my Rockford Fosgate R1675-S', there is no way to get a screw into the bracket as the speaker holes are spaced too far out for the bracket.

Have questions for
?

Perfect fit

Drill a few holes and you're just about done. Made installation less stressful.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Brackets fit nicely, but there was one problem. The speaker mounting screws were to long and extended through the back of the brackets. I had to cut off about 1/2 inch of the screw to make them fit.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Perfect fit

Have questions for
?

A must have when changing speaker size

These came as part of a bundle with Infinity Reference REF-6522EX for a 2014 Honda Ridgeline. Fit was perfect for the Ridgeline. Made installation super easy.

Have questions for
?

Saved me a lot of work

These ended up working great with a little fiddling. It was not clear that you need to break off some of the tabs to get the speaker to fit right. Given how detailed all the rest of the instructions are, this seemed like a strange oversight.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Worked exactly as expected , the fit is not perfect but definitely good enough for the girls I go with.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Worked perfect.

Have questions for
?

Custom Fit 2007 Ridgeline

Critical for fit in my installation of Rockford R165x3 speakers. Had to remove inside tabs, easily done with vise grips since they are pre-scribed for a break off. Used #6x3/4 inch sheet metal screws to secure speaker to mount and #8 x 5/8 inch self tapping screw to secure to door. Perfect fit resulting in top quality install. Glad Crutchfield recommended, would not have been able to do the job without them!

Have questions for
?

Good bracket, needs cutting

These brackets did eventually fit, but I had to dremel out the middle notches to get the speaker to sit flush inside of it. They are sturdy and fit perfectly.

Have questions for
?

Perfect fit.

Fit the factory openings like a glove.

Have questions for
?

A solution to a Honda problem

These are not only needed but required to change out the factory speakers in my vehicle. On the front doors, they fit perfectly, but on the back doors, one of the screw holes hit in the middle of a metal bend. They could have been designed a little different and fit perfectly.

Have questions for
?

Good fit, but not perfect

I'll give it 4 stars, but note that the ears on the bracket don't exactly land well with the count our of the door. I remedied by using 3 self tapping screws and was able to make it work, but still not an ideal fit, but good enough. Also note, (the master sheet I had didn't say this) you may have to remove the plastic inner ears if your speakers are on the bigger side. Do this by using a pair of pliers and simply bending them until they break. Also, the U-channel mounting holes did not work with the stock speaker screws. You will need to supply your own. I used the same self taping screws and made a very snug fit. If the screws don't fit well, GO GET THE RIGHT SIZE. Otherwise, the speakers will bounce their way out of the bracket and will make awful noise later.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

The brackets are everything I needed to make a great system come together. The design is very smart and fits with the factory holes perfectly. Crutchfield is "awesome " thank you guys for the great fit.

Have questions for
?

Not bad, but not perfect

Used these for all doors to a 2006 Honda Ridgeline. Perfect fit to front door, but had to modify a tab on rear doors due to angle of sheet metal. Holds the speakers pretty secure. Would have been nice to have some screws supplied with it.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

the diameter did not match the speaker. I had to cut off the ears with a saber-saw.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

They made it easy enough a child could do it

Have questions for
?

Made speaker install easy

made the install a perfect fit

Have questions for
?

Great

This bracket is needed and does a great fit

Have questions for
?

Requires modification.

Honda Ridgeline stock locations. These provide the extra mounting space needed for the new speakers but I had to cut and modify the mounts to make them fit. One of the mounting holes had to be removed to fit it in the stock location. Inner tabs had to be removed to fit the new jl audio speakers

Have questions for
?

They got the job done in Front

No instructions with these were provided. Instructions for Audio replacement for my 2012 Ridgeline were included with my HU and speaker order. However these instructions referred me to the bracket instructions, none included. I figured out the screws and channels were with the speakers and figured out how to put them on the brackets appropriately, I am no audio expert. Anyway, the best way to secure speaker to bracket is by hand, carefully. As for installing the bracket/speakers into the Ridgeline, a piece of cake with some self tapping screws. Contours in the door panel were a very slight issue on 1 out of 3 screws. But it holds tight. I would recommend this for your Ridgeline, but if you can fabricate your own you might be happier.

Have questions for
?

Cheap and Flimsy

Cheap and flimsy. If you need to drill holes better mount the speaker to the bracket first, it warps under pressure. Ont tab that helps hold in place broke off. Really could be much better. Such a simple product, so many design flaws.

Have questions for
?

2005 Honda CR-V

These worked great on the back doors of my 2005 CR-V. The front doors had a little bit of a contour in the sheet metal and so I ended up using the Metra brackets up front because I could flex them a bit more for a nicer fit, but these would work there too. Just make sure you have some metal screws for the install.

Have questions for
?

2007 Honda Fit

FIt nicely in the both front and rear doors. Some self taping screws completed the install.

Have questions for
?

2013 Honda Ridgeline

Worked fine in my Ridgeline. Had to drill 3 holes to secure it to the frame; lined the frame with Dynamat before the final install. The brackets conformed to the contours of the door just fine with no complications

Have questions for
?

Decent brackets.

These fit OK. I had to do a couple small modifications.

Have questions for
?

It did the job...

The tabs wouldn't fit in the holes, so I ended up breaking them off and using self tapping screws. My 6.5" components wouldn't fit flush in the brackets either. With a little bit of work, overall, they served their purpose.

Have questions for
?

ok adaptors

Ok item but seems cheap and fragile.

Have questions for
?

Ok Quality!!

Front fit fine. Rear was a little harder.

Have questions for
?

Scosche SAHR6 Speaker Mounting Brackets

Worked great for my 08 Honda ridgeline, 20 min both sides hooked up and music playing. Gotta get a set for the rear and my up grades will all most be done.

Have questions for
?

Worked good

Worked good in the front doors of my 08 Honda Ridgeline but needed to be modified for the back. Snapped in place nicely.

Have questions for
?

Adequate.

These mounting adapters are just barely up to the task. They require drilling to mount the adapters to the vehicle, but no screws are included. The holes the speakers mount to are just barely strong enough to put a screw into. Be very careful and almost tighten the screws or you will strip the holes. I would gladly pay extra for a better made adapter.

Have questions for
?

Honda Ridgeline

Didn't fit my honda ridgeline due to sheet metal contours.

Have questions for
?

Made for honda

Great fit, self tapping screws work better ( no need to drill holes )

Have questions for
?

Honda Ridgeline Speaker Adapter

I ordered these speaker adapters for all speaker locations in my 2012 Honda Ridgeline. These only work for the front doors, and they do not fit nor replace the OEM brackets; the OEM snap into place. The adapter rings need to be screwed in and some type of sealant or foam put in place to seal the rings. I installed 5 1/4" component speakers and had to customize a speaker plate to hold the speaker, then secure it on to the ring. I used door panel deadning material to seal the seams throughout. My suggestion on the rear is used the OEM ring and cut out the cone ( I replaced the OEM speaker with a 4 1/2" two way speaker creating a mounting plate); it works great.

Have questions for
?