Scosche SAGMEQ656 Speaker Mounting Brackets

Scosche SAGMEQ656 Speaker Mounting Brackets

They work great.

Have questions for
?

Adapter

Fits perfect on the regulator. Well need to drill a hole but it will fit

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Had to drill holes due to not being made for the application I was using them for

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Perfect fit for my 12 Equinox!!! Thank you for including these in the purchase of my speakers!!!

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

adapter brackets were easy to install and performed as described

Have questions for
?

2011 STi

I have a 2011 STI, it wasn't a Cinderella shoe. But I made it work. Had to drill a hole, on the bottom left to make fit. They do the job. Better then anything else I've found

Have questions for
?

Works fine

Dunno what to say, they do what they are suppose to lol.

Have questions for
?

No inserts, no upgraded speakers

Couldn't have installed the speakers without these inserts. Worked great!

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

The adapters fit the holes, but the hardware is somewhat a mystery. The Crutchfield instructions refer to the mounting brackets instructions (none exist that I could find). So we had to scrounge up fasteners to fit. Better installation or fastener combination would be an improvement.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

I received these with my purchase of 6.5" speakers for a Kia Rio 2013 Hatchback. I wasn't impressed. The mount fit on the door, but the speakers didn't fit on the mount unless they were reversed. I ended up going old school and made my own MDF rings. After cutting out two matching 3/4" rings, glueing together, and painting to make sure they hold up under any potential moisture, I also used some non-hardening modelling clay to help build a load around the mount against the doors. In addition, I also cut the speaker ring off the door panel itself, and ended up using some thick furniture felt to reduce any potential vibrations against the MDF rings and plastic. Doing this, I could have gone with a 7" speaker easily even though the Crutchfield "specialists" indicated the 7" speakers wouldn't fit. Building up the 1.5" ring gave me that extra depth I needed. While I understand these mounting brackets are designed to be as universal as possible, they honestly sucked for the installation on the 2013 Kia Rio. At the end of the day I threw the rings in the trash where they belong.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Good product for mounting speakers in my 2011 Equinox

Have questions for
?

Good, but Metra 82-8900 is better for 2012 Forester rear door

I believe the product is well-designed and constructed of appropriate material to do a good job in the vehicles it fits. That being said, my 2012 Subaru Forester was not such a vehicle. Crutchfield sent it along for free with speakers, as they do, and noted an additional hole would need to be drilled to make it fit. Unfortunately, there is only one orientation where 2 of the 3 holes would line up and the place a new hole would need to be drilled was awkward and difficult, as it was on an angled surface and would require removal of a plastic part of the panel (the bit holding the original speaker hole). The good news is I had an extra pair of Metra 82-8900s and they fit the stock holes much better (not quite perfectly; one screw sits a little further from the overall center than would be ideal, but no additional holes are needed and they hold the bracket just fine).

Have questions for
?

Poorly Made - Screw holes too large

The brackets fit the existing location just fine, and I had no problems lining up holes for the speakers. The problem I had is that the screws that came with the bracket were too small for the holes in the plastic. I was able to get the screws just barely tight enough to stay in. Now after a few years, they are coming loose and the speakers are rattling in the doors.

Have questions for
?

throw them out

bought a whole speaker system from Crutchfield. the screw holes were terrible and did not hold any screws, i had to make my own good thing they were free i can see why...

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Used these adapters for a 2012 Chevy Equinox with the lowest model stereo system in the front door. They line up perfectly with the original mounting locations but the holes for the 6 1/2" speaker were slightly off. I was able to work around and get a tight fit but took some time to get perfect.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

The spacers were perfect. Kept the new pioneers close to factory specs.

Have questions for
?

Must have for some GM doors

fit the factory space great with no mods for my 2006 Saturn Vue. For one set of speakers no tabs to remove, the other set had to remove all the tabs but was easy. Beats having to custom fit a bracket. No way to mount any speaker directory to door since hole was larger than speaker basket.

Have questions for
?

Good product, bad recommendation (C'mon, Crutchfield)

Does not fit 2008 Subaru Impreza WRX. Make sure to read into each item the Crutchfield team recommends for your vehicle, as they are not always compatible.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Definitely does NOT nicely fit the rear door of a 2011 Impreza. Required a little finagling to work in the front doors, and major finagling to shoehorn them into the back doors. The screw holes do not line up, and there isnt enough extra plastic to make them wider to accommodate the factory screw locations. In forcing the misaligned screw holes, it tweaks the bracket slightly out of circular shape, making the speaker cage load-bearing. Probably not a huge problem, but the whole thing is under tension, which is not ideal. There has got to be a better solution for our Subarus.

Have questions for
?

Great Speaker bad brackets

These did not work at al for my 08 Impreza four door. They either didn't line up or they were too shallow. The screws included were the wrong length and came through the back side of the mount and were touching metal and grounding out my system. A job that should have taken 1.5 hours ended up taking 4 hours over two days and several trips to the hardware store.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Crutchfield recommends these for the GE/GR body WRX/STI but that is not even close to the case. New holes had to be drilled into the doors to mount these rings as they did not fit even close to the stock location. I would've done away with them if my magnets wouldn't have interfered with the window glass but that was the case without the rings. Luckily I have them mounted flush so they aren't rattling like others have complained about

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

They do not fit flush to the door, nor do the screw holes line up. I had to drill them to make them fit. There's now a rattle from not fitting flush against the door. They are not a direct fit as described.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Was not a very good aftermarket mount for my application had to be modified to make work

Have questions for
?

Holes aren't in the right place

Didn't fit in my 2011 Subaru Impreza, Only 2 holes lined up

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Great product.

Have questions for
?

Perfect fit

Bracket fits perfectly, so now the speakers do as well

Have questions for
?

Solid product not made for Subarus

So the construction of these are very solid. Unfortunately they do not fit a 2011 Subaru Impreza with a stock premium sound system. I attempted to join the mounts to the OEM speaker mounts. This made the speaker to proud to mount the door panel. I was hoping for a product that would be a direct bolt and go like the stereo head unit adapters. At least it was included in the speaker purchase and not extra.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

best purchase I ever made

Have questions for
?

Does NOT work with 2010 Subaru Forester

They the speakers mount to the adapter is bad. I had to use long screws and make holes in my Forester to solidly mount the speakers. This is NOT an EXACT fit for the 2010 Subaru Forester. You need to make a new mounting hole for the front speakers and it just barely works. The back are too far away to use. These adapters are NOT recommended for the 2010 Subaru Forester no matter who tells you it will work.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Fit great and made the speaker installation a breeze.

Have questions for
?

Not for 2010 Suburu Forester

Crutchfield site said these would fit my 2010 Suburu Forester. I tried every orientation possible and only 2 out of 3 screw holes would line up with holes in door. I ended up drilling a new hole in the bracket.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

These did not fit my 2007 Equinox front doors and came with no instructions to indicate any alterations were needed to fir the back doors. Modifications to the both the brackets and some metal work to the door were needed to make these work in the front. I had to remove tabs from the brackets so that the Focal speakers would fit the bracket for all doors. With no instructions indicating modifications were expected, this was a frustrating phase of the project.

Have questions for
?

Needed accessory

Adapters worked well for the front door location of my '01 Saturn L200, once I figured out the necessary modifications needed to complete the install. A welcome and free piece of hardware to make the install a little easier.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Maybe I was sent the wrong brackets, but I'm sorry these were a real pain. The speakers do not, repeate do not fit these. I finally went and purchased longer screws and installed these brackets backwards to get my speakers installed. I know it's wrong but I wanted my tunes.

Have questions for
?

Perfect fit

Perfect fit for enlarged holes.

Have questions for
?

Makes it so much easier.

Made all the difference. Mounted speaker to it and mounted bracket to door. DONE. I tried to install the rear speakers without it and it didn't work, ended up buying a this bracket for the rear as well. Install for dummies ... that is how easy it makes it.

Have questions for
?

Didn't fit

Didn't fit the car. At all. Wrong size. Wrong screw holes didn't even fit the speakers

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Only matches 2 of the three mounting holes on my subaru so the y rattle a little

Have questions for
?

Perfect for replacing my factory speakers

These brackets were a necessary evil due to the fact my factory speakers were installed using rivots. They were included in the purchase of speakers and worked great.

Have questions for
?

Worthless

If I could give these a 0 rating I would. Completely useless In my 2015 Lancer. They came with the Jensen Dubs 5 1/4" speakers for my front and back doors. Not only did they fit the door poorly requiring me to drill all new holes, the speakers didn't fit them either!

Have questions for
?

Please send the right speaker mounts for JBL Stage 600c 6-3/4 speakers

The speaker mounts fit fine onto the door and holes for the screws matched up well. These mounts were shipped with the JBL-Stage-600C-6-3/4" Item #109STAGE6C. The speakers don't fit into the mounts and I am unable to secure the speakers to the mounts. I have to reinstall the factory speakers to the car now. Not a happy customer.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Fit my 2016 Subaru Impreza front door speakers with only minor modification.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

They fit, and work well. What more can I say.

Have questions for
?

Work as expected, sturdy, and free from Crutchfield

These worked fairly well. I used them to install JVC CS-DR620 6 1/2" speakers (front & rear) in a 2008 Subaru Impreza WRX. The instruction PDF you can download for it is pretty useless. It only says you can remove the inner tabs, which I didn't have to. If you plan to use these, the side with the lip should be installed against the car door. I was able to mount the bracket using the two lower (left & right) factory holes for the front and drilled the top hole. It says use a 1/8" drill bit, but you have to make the hole a little bigger for the factory screw to fit. For the rear speakers, I was able to arrange the bracket so I could use the top factory hole and lower left factory hole and had to drill one hole for the lower right. I used the screws that came with the JVC speakers to the bracket. I just screwed it to the plastic as the metal clips supplied with the speakers can't be used with the bracket. Also, there is also no slot to run the speaker wire, I just pinched it between the speaker and the bracket, didn't seem like a big deal. They were free and they work, not much more you can ask for. I think some people expect solid gold brackets that fit every vehicle ever made for free. I appreciate that Crutchfield provides these for free and they only require a small modification and some common sense. I'm happy with them, I'd give them 3 1/2 stars.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

These do the job, easy to use and modify.

Have questions for
?

terrible

If i could give these no stars i would. they do not fit the new speakers at all. i had to drill all new holes for the speaker to fit. i also had to go to the hardware store to get new screws to work with these. I was told when i got them that i would have to drill one hole in my car. I did have to do that but i did not think i would have spent an hour just messing around trying to get them to work with the speaker and with the car itself. they did not come with any instructions on how to use them and they didnt come with any screws and the screws that came in the factory speakers would not have worked for these they were too short. they also need a hole for the speaker wires to go through. I really wish i had looked into getting something that would have fit 100%. I know that they gave me them for free but i would have paid to have something that i didnt need to modify so much.

Have questions for
?

works

worked in my 2016 kia rio 5 which has stock 6.5 speakers. only issue was out of the 3 mounting holes only 2 can be used. the 3 u need to use a washer on the screw to catch the bracket.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Received with a speaker up-grade I purchased for a 2010 Forester. Useless, did not come close to aligning with the door frame or the new speaker, I would have had to drill at least 5-6 holes in each inner door frame to use this bracket. And after all that the support would still be questionable. Since the install was in an SUV, that fact made them useless. I decided to gut the OEM speakers, using the plastic surround/frame as a new mounting bracket. This change reduced the drilling per door in half and the end result looked and performed like a factory install. I called tech support during the early stages of the install. I was treated like a novice. The tech did not want to hear about the fact they did not fit. He stated the SD speakers came with self-tapping screws. Gee, thanks bro. This was a surprise, first time in 30 years doing business with Crutchfield that tech support did not come through.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Excellent fit to my '07 Sonata door.

Have questions for
?

Doesn't fit.

For some reason Crutchfield thinks these fit my 2013 Impreza WRX STi, they do not. The factory speaker mounting holes do not match theses speaker brackets, so a new hole has to be drilled. Another hole also needs to be drilled to allow the speaker wires to pass through from behind the speaker.

Have questions for
?

Did Not fit

Product did not fit the car as described, had to drill new holes in door to get speaker to fit. Would not have rated it a 2 if there was something that indicated that may be necessary

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Great fit, exactly as described.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Perfect fit to the door. Speakers fit a little tight.

Have questions for
?

Can't beat the price, but no instructions

These speaker brackets did not really line up at all with the hole in my door. It required me to drill two new holes and the speaker receiver holes should have been smaller to accommodate self tapping screws from the speaker.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

My first time installing speakers. The installed on my doors perfectly but when I tried attaching the speakers only 2 holes lined up so I ended up drilling new holes for the mounting screws.

Have questions for
?

Installing aftermarket speakers

Holes lined up fine but be sure to measure your depth. I still had to use spacers to install my 6.5" speakers with this adapter. Then had to deal the gap with duct tape or expanding foam to get the bass I wanted.

Have questions for
?

6 1/2" speaker brackets

These brackets spaced out the speakers correctly to the door panel . However they did not match up with existing holes in the doors and the speakers did not screw in to the brackets well. They need to have more plastic around the screw attachment areas to hold better.

Have questions for
?

Works if modified with 2012 Focus SE

They did the job but they didn't match up with the holes that the stock speakers used. I had to use a self-tapping screw on all four brackets to get them to work. 2/3 of the holes matched up and the instructions did say that you might have to do this, I just wasn't aware of that when purchasing these.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

great fit solid product

Have questions for
?

Worked Well!

I saw so many complaints that I was a bit apprehensive at first. Two of the three original holes for this mount lined up just fine. Drilling a quick hole for the third mount was quick and without issue. There were some inner tabs that must have been meant for smaller sized speakers, but in my case, I was moving up to a 6 3/4" size to the cast tabs had to go. Several reviewers fussed about cracking the plastic mounting ring when attempting to break these off. Out of concern for doing this, I just used a dremel tool and ground those little things right off. It was recommended to cut a notch for wires to pass through, so again, I used the dremel tool to cut out a little chunk. I thought these rings were great. Best of all, Crutchfield included them with the speakers. Yahoo!

Have questions for
?

not a perfect match

Since the mounting brackets that came with my speakers weren't compatible with my car, Crutchfield sent me these. Unfortunately, these didn't fit either. I was warned that I would need to drill new holes in my car doors, but why? It doesn't seem like it should be hard to make/stock adaptors that fit. Ultimately I got them to work, but I had to drill some holes in these plastic brackets.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Fit as expected. Would like to have seen a better way to screw the speaker into the adapter plate, or come with appropriate screws, but for the price, can't complain.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

This definitely helped keep my new Alpine 6 1/2 speakers from touching my window when I roll it down.

Have questions for
?

2015 WRX

Does Not! properly fit 2015 WRX as advertised! factory speaker mounting holes do not match theses speaker brackets.

Have questions for
?

2016 Hyundai Elantra install

These do not work if you're installing 6.5 inch speakers in a 2016 Hyundai Elantra. They look like they would work for a 5.25 speakers. Reusing the factory mounts worked fine for me. You don't have to remove them to use them with 6.5 inch speakers but you have to cut the supports off to allow the new speakers to fit. There are other good descriptions on how to do this online.

Have questions for
?

Grrr!

They fit car just fine just not the 6 1/2" speakers. I could've hast as easily came up with my own modification. That may have worked just fine with a smaller speaker.

Have questions for
?

Rear door 2013 Hyundai Elantra - salvage the factory bracket

I see a review that said these were fine. However, they're too short - the speaker won't reach the door panel. I reused the bracket that is an integral part of the factory speaker assembly: Cut the veins supporting the magnet end of the driver, cut the wires, used chisel to separate driver from bracket (Crutchfield suggested next time I heat it to 150°F) Then attached new driver to bracket with silicone cement and some #4 bolts and nuts. and put some self adhesive foam to seal with the door panel. Reuse allowed me to use the factory wiring, and just solder wires to the vane that has the original wiring. The result works well.

Have questions for
?

Meh

These really didn't fit my 2012 Focus. I actually threw them out. They still required modification and so did my stock mounts. I just used the stock ones instead.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

I switch the speakers in a equinox 2011 and this mounting brackets were perfect for the new speakers to fit properly, very happy Crutchfield included them

Have questions for
?

Decent Speaker Bracket

Overall these will get the job done. They are made to fit 5 1/4 and larger speakers. If you do use the larger speakers such as I did you will have to break the inner mounting hole out to fit the speaker. I do recommend being very careful when doing this as they are kind of fragile. I took the route of using a pair of pliers to break them and ended up breaking the bracket. After that happened I used a Dremel to cut the others off and that worked quite well. I did contact Crutchfield about the issue and they where very quick to apologize and ship a new set immediately. Overall I am very satisfied with the product and more impressed with the customer service that comes from Crutchfield. That's why I have shopped with them for nearly 20 years.

Have questions for
?

Useless

These were useless for installation. The did not fit the 2013 Forester, they made the speaker stick out too far to fit the door panel over, they did not attach easily to the speakers.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Product does what it should was the correct part for my 2014 focus st online but only two of the three mounting holes lined up on the vehicle and I had to use a drimel with sanding wheel to open up the speaker hole more due to my 6.5 speaker wouldnt seat all the way down.

Have questions for
?

Did not fit

Did not fit even though the website said it would. I ended up hollowing out my factory speakers and turning them into mount brackets. I would suggest doing that, instead of buying this product. Save your money.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Fit perfectly. Shipping was quick and as always the crutchfield team was very helpful.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Included free with my purchase. Perfect fit and easy installation.

Have questions for
?

Excatly what I needed