About the Sony XM-D9001GTR
Sony's Xplod amps combine form and function in a mix that'll make your system look and sound great. On the outside, the sleek inverted heat sink keeps vital internal components running cooler and lasting longer. Removable terminal covers keep all the wire connections protected and out of sight for a clean-looking installation.
Underneath the hood, the XM-D9001GTR mono amplifier delivers 550 watts to a single 4-ohm sub, or 900 watts to a pair of subs plenty of power for even the most demanding subwoofers. Signal-sensing speaker-level inputs activate the amp automatically when it's connected to a factory radio, so there's no remote turn-on lead for you to install.
You can adjust the frequency filter to tailor the signal going to your subs, while a bass boost adds extra punch to the lows. Preamp outputs simplify setup when it's time add another amp to your system.
- mono subwoofer amplifier
- 550 watts RMS x 1 at 4 ohms (900 watts RMS x 1 at 2 ohms)
- 2-ohm stable
- low-pass crossover (50-300 Hz, 12/24 dB/octave)
- variable bass boost (0-10 dB at 40 Hz)
- MOSFET outputs and power supply
- CEA-2006 compliant
- speaker-level inputs with high-level sensing
- preamp inputs and outputs
- 4-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 15-13/16"W x 2-3/16"H x 10-13/16"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # XMD9001GTR
What's in the box:
- Mono amplifier with three 30A fuses inserted into the chassis
- 7.5" Speaker-level input harness (with 4-pin Molex plug on one end)
- 4 Hex-head self-tapping screws
- Operating instructions (English/French)
- Warranty sheet
Sony XM-D9001GTR reviews
Thanks for submitting your review
More details on the Sony XM-D9001GTR
Features & specs
|RMS Power Output (Watts x Channels)||
550 x 1 |
|Peak Power Output (Watts x Channels)||950 x 1|
|Power at 2 Ohms (Watts x Channels)||900 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||5-300Hz Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||65 dB|
|Low-Pass Crossover Frequency||50-300 Hz|
|Low-Pass Slope (dB/octave)||12/24 dB|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0-10 dB|
|Bass Boost Frequency||40 Hz|
|Fuse Rating||30 x 3|
|Speaker Level Inputs||Harness|
|Preamp Outputs||1 pair|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Protection Circuitry: The Sony XM-D9001GTR amplifier has 3-way protection circuitry, which protects the amplifier in the following cases:
- Thermal: shuts off the amp when the operating temperature is too high
- Short circuit: shuts off the amp when the speaker outputs are short-circuited
- DC Offset: shuts off the amp when the speaker wires or ground lead is not securely connected, generating direct current
Low-pass Filter: The internal low-pass filter can be adjusted from 50 to 300 Hz. The slope of the filter can be set to 12 dB or 24 dB per octave.
Bass Boost: For added low frequency performance, this amplifier has a 0 to +10 dB variable bass boost centered at 40 Hz.
Subsonic Filter: The subsonic filter allows the amplifier to block ultra-low frequencies that your subs can't reproduce, improving the efficiency of your speaker system. The filter can be set to 6 Hz or 70 Hz. The slope of the filter can be set to 12 dB or 24 dB per octave.
Preamp Outputs: The preamp output jacks provide a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the amplifier location. These outputs provide a full-range signal.
Power Connections: The power and ground connections are 0.547" wide screw terminals that will accommodate up to 4-gauge wire. The remote turn-on terminal is 0.349" wide and will accept up to 8-gauge wire. A Phillips-head (not supplied) is required to tighten/loosen the terminals.
Speaker Connections: The speaker terminals are also 0.349" wide and will accommodate up to 8-gauge wire. A Phillips-head (not supplied) is required to tighten/loosen the terminals.
High Level Input: The amp comes with a 2-channel speaker-level input harness with a 4-pin Molex plug on one end. This allows you to more easily connect this amplifier to a factory deck or a receiver without preamp outputs.
Amplifier Wiring: This amplifier uses three 30-amp fuses, so its total fuse rating is 90 amps. Since pre-packaged 4-gauge amplifier wiring kits normally have 60-amp or 80-amp fuses, you will need to replace the fuse and fuse holder in the kit with a 100-amp ANL fuse (item # 211FANL100) and ANL fuse holder (item # 211FHXL4).