Chat
Contact us
Close contact box
Connect ID #
349 507 173 3
Connect ID #
349 507 173 3
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

Our contact center is currently closed.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

The Epicenter® by AudioControl

Bass restoration processor (White)

Item # 161EPICEW

You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any...

You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any...

Top seller

Item # 161EPICEW

In stock

$199.95 Sale: -$50.00 off Sale: ends tomorrow

$149.95

Other options

About the The Epicenter® by AudioControl

Kick up the bass

You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any kind of music — from classical, jazz, and rock to folk and Tejano — with an AudioControl Epicenter bass restoration processor. Most factory radios dial down bass response to protect flimsy speakers, so when you do add a subwoofer, there's no bass to play. The Epicenter will bring it back.

Kick up the bass

You like all the bumpin' bass you hear in hip hop, rap, and EDM? Well you can put that deep, biting bass into any kind of music — from classical, jazz, and rock to folk and Tejano — with an AudioControl Epicenter bass restoration processor. Most factory radios dial down bass response to protect flimsy speakers, so when you do add a subwoofer, there's no bass to play. The Epicenter will bring it back.

AudioControl's legendary Epicenter bass processor maximizes the low-frequency power and punch of your bass system, whether it's a simple powered bass tube or a full-blown competition setup. Simply install this processor between your receiver and your amplifiers or crossovers, and you'll finally be able to hear all the good bass you've been missing. An included wired remote lets you control the amount of thump from the front seat.

How does it do it?

Sophisticated processing analyzes the incoming signal and synthesizes low-bass fundamental tones, increasing bass response tremendously. The Epicenter connects to any receiver with preamp outputs — its balanced inputs will reject noise from your car's electrical system. A subsonic filter removes extreme low frequencies from your signal so your amps and subs will play more efficiently, while a single band ParaBass equalizer lets you fine-tune the bass tone.

READ LESS

Product highlights:

  • bass restoration processor (white)
  • increases bass response from your system
  • 2-channel preamp inputs and outputs
  • Para-Bass controls adjust center-frequency and width of bass processing
  • fixed subsonic filter (33 Hz, 12/dB octave)
  • wired dash-mount bass remote
  • 8"W x 6-1/2"H x 1-3/16"D
  • frequency response: 10 to 100,000 Hz
  • weight: 1.7 pounds
  • warranty: 5 years
  • Our 60-day money-back guarantee
  • MFR # 8410191

What's in the box:

  • Pre-amp Bass Restoration Processor (white)
  • Remote dash mount control
  • 20' RJ-14 cable
  • Owner's manual
  • QC checklist

Customer reviews

Loading reviews...

The Epicenter® by AudioControl reviews

Average review:

31 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

More details on the The Epicenter® by AudioControl

Russ B.

Product Research

Features

Bass Restoration: Rather than simply turning up the bass, the patented bass restoration circuit takes a full range input signal and measures the upper harmonics of the bass frequency range to determine what frequencies have been lost during the recording process, then correctly restores the missing bass information. The remote rotary knob allows you control how much bass is restored to the system. A full range signal is output from the Epicenter that can feed a full range amp, a subwoofer amp (with built-in crossover), or an outboard crossover.

Para-Bass: Para-Bass is a single band, parametric equalizer for the bass output. The center frequency is continuously variable from 27 Hz to 63 Hz. The width of the band is also adjustable.

Bass Maximization: The Bass Maximization circuit allows The Epicenter to maximize the bass output of any system while restraining destructive bursts, which can damage speakers. the 5.0 volt factory setting can be changed to 2.5, 7.5, or 10 volts if the amplifier and speakers can handle it.

Remote: The bass restoration level is adjusted using the included wired remote. The remote is designed to be dash mounted, within reach of the driver; it can be mounted under the dash with the supplied bracket, or the bracket can be removed and the knob and LED can be custom mounted through the dash. Dimensions:

  • Width: 2.557"
  • Height: 1.489"
  • Depth: 1.824" (2.448" including knob)

Subsonic Filter: The subsonic filter crossover point is 33 Hz; it's governed by a replaceable chip, so it can be changed to 20, 25, 30, 35, 40, or 45 Hz.

Balanced Inputs: Using the balanced differential input circuit cancels noise picked up in the transmission line between the Epicenter and the the source unit. The inputs can be set to balanced or unbalanced if needed.

Ground Isolation: The power supply ground is switchable, in case of ground loop noise. The factory position is fully isolated (typically the best choice), but can be changed to Ground or 200Ω.

Terminal Block: The power/ground/remote terminal is removable; the wiring is attached to the block, then the block is plugged into the Epicenter.

Specifications:

  • Maximum Input Level: 15 volts RMS
  • Maximum Output Level: 9.5 volts RMS/13 volts peak
  • Frequency response: 10 Hz-100 kHz;±1dB
  • THD: 0.003%
  • S/N Ratio: 130dB
  • Balanced Input Noise Rejection: >60 dB
  • Input Impedance: 10 kΩ
  • Output Impedance: 150 ohms

Loading accessories...

Customer Q&A

9 questions already asked

Q
I already have a DQ-61, will this help out my subwoofers sound better?
[ Frank  Jul 20, 2020 ]
2 answers
A
Yes, if you take the subwoofer rca outputs and plug them into the Epicenter then your sun amp it will work. Look at the DQ61 manual, it shows a picture on how to install with Epicenter on DQ61.
[ Michael  Aug 26, 2020 ]
A
Nope
[ Sean  Jul 20, 2020 ]
Q
I already have an amp in my trunk. Where do get power from? Do I use a distribution block to get the epicenter 12v power?
[ Jeffrey Moeller Jr.  Jun 29, 2020 ]
3 answers
A
The epicenter is not a high power device, it does not require a high amp power source like your amp. Mine is tied into the same batt and ign feed as my Eq and head unit. You can also go directly to the fuse panel.
[ MIKE  Jul 04, 2020 ]
A
You not have to put a distribution block..the epicenter no need to much power ..all you need bring 3 wires from your amp to the epicenter..the ground,the remote and the ground!!
[ Miguel  Jul 03, 2020 ]
A
Yes. Just use a splitter.
[ Thomas  Jul 03, 2020 ]
Q
Do I need this if I'm going to be running the LC7i already ?
[ BassForMe  Jul 24, 2019 ]
1 answer
A
You only need the Epicenter if your going to listen to music that lacks bass information. If you listen to Rap it is way over board in the bass with all of the settings at minimum. If I had to do it over again I would bag the epicenter and just use your crossover. Your LC7I should sound great without it I'm thinking.
[ GUY  Jul 24, 2019 ]
Q
Is the subsonic filter only active when the Epicenter is actually turned on?
[ T-Bone  Jan 24, 2018 ]
2 answers
A
Yes that's correct.
[ Sixtus Jn  Jan 24, 2018 ]
A
The subsonic filter is on all the time even if the Epicenter's processing is not being used. The PFM subsonic filter shipped with the Epicenter is set at 33 Hz. Sounds below 33 Hz will still play but at a decreasing volume as lower the sound . You can buy PFM filter chips from Audiocontrol directly by going to the AC website, clicking on "CAR" at the top, scroll down to "ACCESSORIES", and then click on "MODULES", and finally clicking on the "Buy Now" link on the blue line at the top. You have to pick the 18 dB/Octave choice for the Epicenter. The 24 dB/octave choice is for AC crossovers. Frequencies from 15 Hz and up are available and cost $10 each plus S+H.
[ Charles  Jan 24, 2018 ]
Q
Does this product help to add the missing bass to the car door speakers? Only reason im looking at this is to improve my speakers. I have two 12 subs. I dont need sub bass. I want speaker bass.
[ Nick  Aug 22, 2017 ]
3 answers
A
You want more bass out of your door speakers? What crossover is used for them? Are they big enough to produce what you're looking for? The Epicenter adds bass back into music that may have been removed when converted to MP3 or during studio recording, etc. Most of what it adds to the music is in the sub bass range. This product doesn't necessarily add more volume throughout the sub bass range, only at the frequencies where it's been taken out. Audiocontrol's website has a great explanation of what it does and at what frequencies.
[ Charlie  Aug 23, 2017 ]
A
Not unless your door speakers are hooked up to your power amp, in which case I would recommend an LQ7 or LQ9 it lets you control the sound all around to your preference.
[ Antonio  Aug 22, 2017 ]
A
No, this will not get more bass into your door speakers. You are looking for more midbass, which is typically between 50-250 Hz. The Epicenter works its magic mostly under 50Hz. What you need is dedicated midbass speakers that are at least 6-1/2 inches in diameter or larger and have plenty of amplifier wattage powering them to get good midbass out of the door locations. There are other tricks to improve your midbass like adding sound damping materials to the doors and sealing all holes in the door. Search Youtube for videos on how to improve your midbass. Here are a couple of videos to get you started: 1. https://youtu.be/S7WKCFHGwRY 2. https://youtu.be/h3EXuHlBy4M Hope this helps.
[ Charles  Aug 22, 2017 ]
Q
Does the Epicenter also act as the 9.5V RMS line driver or is it necessary to play an Overdrive in front of the Epicenter?
[ Mbrogz3000  Mar 31, 2017 ]
1 answer
A
The Epicenter can provide up to a 9.5volt signal output so, an external line drivers is not required. I hope that helps. My Bio: https://www.crutchfield.com/Support/Bio.aspx?bio=5
[ Ryan  Apr 06, 2017 ]  Staff
Q
Where do I connect the epicenter's rca's to the Headunit.. Sub out or rear out "full range".?? Or do I connect them on sub out and adjust the Headunit's settings to full range. Or is it the other way around. Please help.
[ Edgar  Jan 08, 2016 ]
1 answer
A
Edgar, I haven't hooked it up as of yet. The instructions note that you should hook it to the full range output before any crossovers. If your sub amp has an internal crossover, then I would set the head unit output to full range and make the frequency cut at the amp. I hope this helps. Thanks,
[ John  Jan 08, 2016 ]
SHOW MORESHOW LESS

Loading articles...

TOP