About the Kicker 11ZX350.4
Better sound in your car
Better sound in your car
This Kicker ZX350.4 4-channel amplifier will power up your music with 60 watts RMS for each of your four speakers or components, so it's perfect for handling your front and rear speakers. As another option, you can put the amp in 2-channel mode to drive a couple of subwoofers with up to 175 watts RMS each. This amp will run reliably even when pushed hard, due to its heavy-duty internal components and the efficient cooling system it uses as it boosts your music's power.
Works with almost any stereo
Kicker employs their Fail-Safe Integration Technology (FIT™) to reject noise and stop any interference generated by your car's electronics, so you'll enjoy your music clean and pure. Speaker-level inputs make it simpler to hook this amp up to a factory system. You can tune for almost any speaker or subwoofer with the variable high- and low-pass filters. A bass boost gives you even more kick, if you're in the mood.
Product highlights:
- 4-channel car amplifier
- 60 watts RMS x 4 at 4 ohms (90 watts RMS x 4 at 2 ohms)
- 175 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode)
- CEA-2006 compliant
- variable high- and low-pass filters (50-200 Hz, 12 dB/octave)
- variable bass boost (0-18 dB at 40 Hz)
- Class AB amp technology
- Fail-Safe Integration Technology eliminates noise from your vehicle's electrical system
- preamp and speaker-level inputs (speaker-level input requires an optional adapter)
- 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- fuse rating: 20A x 2
- 13-1/2"W x 2-1/8"H x 9-5/8"D
- warranty: 2 years (extends to 3 years when purchased with a Kicker PK8 amp wiring kit)
- Our 60-day money-back guarantee
- MFR # 11ZX3504
What's in the box:
Kicker 11ZX350.4 owner's manual
- 4-Channel amplifier
- Two 20-amp fuses (installed)
- Owner's manual (English/ Spanish/ German/ French)
Reviews
Customer reviews
Loading reviews...
Thanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Kicker 11ZX350.4
Features & specs
| Performance | ||
|---|---|---|
| RMS Power Output (Watts x Channels) |
60 x 4 | |
| Peak Power Output (Watts x Channels) | N/A | |
| Power at 2 Ohms (Watts x Channels) | 90 x 4 | |
| Bridged Power (Watts x Channels) | 175 x 2 | |
| Minimum Impedance Bridged | 4 | |
| Minimum Impedance Unbridged | 2 | |
| Minimum Impedance | 2 | |
| Best Frequency Response | 20-20k Hz | |
| THD at Rated RMS Power | 1% | |
| Signal to Noise Ratio | 95 dB | |
| Input Voltage | 14.4v | |
| Features | ||
| Amplifier Class | AB | |
| Low-Pass Crossover Frequency | 50-200 Hz | |
| Low-Pass Slope (dB/octave) | 12 dB/octave | |
| High-Pass Crossover Frequency | 50-200 Hz | |
| High-Pass Slope (dB/octave) | 12 dB/octave | |
| Bass Boost | 0-18 dB | |
| Bass Boost Frequency | 40 Hz | |
| Fan Cooled | No | |
| Fuse Rating | 40 | |
| Speaker Level Inputs | --- | |
| Preamp Outputs | No | |
| Width (inches) | 13-1/2 | |
| Height (inches) | 2-1/8 | |
| Depth (inches) | 9-5/8 | |
| Parts Warranty | 2 Years | |
| Labor Warranty | 2 Years | |
Product Research
Controls
4-Channel Amp: The front and rear sections of the amplifier (labeled Amp1 and Amp2) have independent gain, crossover, and bass boost controls.
Gain: The rotary gain controls are continuously variable from 125 mV to 5 V when the Input Sensitivity switch is set to Low and 250 mV to 10 V when the Input Sensitivity switch is set to High.
Crossovers: The front and rear crossovers can be independently set to high-pass, low-pass, or turned off (full range). The crossover points are continuously variable from 50 to 200 Hz and the slope is 12dB per octave.
Auto Turn-on Switch: The amp offers three automatic turn-on modes; select from:
- +12V: connect a wire from the remote turn-on lead from your source unit to the REM terminal on the amplifier; this is the preferred turn-on method
- DC Offset: turns the amp on when a 6-volt DC offset is detected at the high-level speaker inputs when the source unit is turned on
- Audio: detects the incoming audio signal from your source unit and automatically turns the amp on; will not work if the input gain control is not set properly
Bass Boost: The bass boost circuits provide up to 18dB boost at 40Hz.
Fader: When powering four speakers and using both the front and rear inputs, turn the fader switch on. To supply all four channels from only one input, turn the fader switch off.
Connections
Left Side of Amplifier:
- +12V (power): set screw terminal
- REM (remote turn-on): set screw terminal
- GND (ground): set screw terminal
- Fuse: two 20-amp ATO fuses
Right Side of Amplifier:
- Speaker Outputs: four pair of set screw terminals
- RCA Input: two pair of stereo RCA input jacks; also used for speaker level input (item number 20609ZiSL needed, sold separately)
Amp Wiring Kit: Kicker recommends using an 8-gauge wiring kit with this amplifier.
Loading accessories...
Customer Q&A
Loading articles...
