Contact us
Close contact box
Connect ID #
980 004 941 3

Call center hours

Connect ID #
980 004 941 3
Chat
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

We're sorry, chat is not available at this time. Please visit our Support page to find the help you need.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-800-955-9091

Thank you, !
Our conversation will be emailed to
Please enter a question  
Please select an email topic.  

Looking for tech support?
Please call us at 1-800-955-9091

Need help now?
Call an advisor: 1-888-955-6000

Please enter your name.  
Please enter your US phone number.  
Please enter an email.  
Please enter an email.  
Please enter a message  

Calls may be recorded for training and quality control purposes.

Crutchfield call centers are located in Virginia USA.

Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

Crutchfield call centers are located in Virginia USA.

Kicker DXA125.2

2-channel car amplifier — 30 watts RMS x 2

Item # 20641D1252

Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact...

Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact...

Oliver
Need help?
Contact our Virginia-based experts.
Discontinued item
2 questions - 2 answers

Item # 20641D1252

Oliver
Need help?
Contact our Virginia-based experts.

About the Kicker DXA125.2

Power your music

Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact chassis that'll fit into a lot of places in your vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the DXA125.2 in bridged, 1-channel mode to power a subwoofer with 125 watts RMS..

Power your music

Kicker's DXA250.2 2-channel amplifier will deliver 30 watts RMS each to a pair of speakers from a very compact chassis that'll fit into a lot of places in your vehicle. This amp delivers around three times the power of a basic factory system, so you'll add a lot of clarity and punch to your sound. You can also use the DXA125.2 in bridged, 1-channel mode to power a subwoofer with 125 watts RMS..

Works with a factory stereo

Kicker's Fail-Safe Integration Technology (FIT™) allows you to tap into your vehicle's factory speaker wiring for the amp's input signals without needing a converter. The "differential-balanced" inputs also help prevent audio interference and noise from entering the system.

Kicker DXA125.2

DXA125.2 input and control panel

Tone controls to help get the job done

The DXA125.2 features separate controls that work with a variety of different speakers or subs. A high-pass filter clears out rumble from small speakers so they can play more efficiently, while a low-pass filter adjusts the bass frequencies going to your sub, so it'll play cleanly. The bass boost can add some extra foundation to the sound if you want.

READ LESS

Product highlights:

  • 2-channel car amplifier
  • 30 watts RMS x 2 at 4 ohms (60 watts RMS x 2 at 2 ohms)
  • 125 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode)
  • CEA-2006 compliant
  • variable high- and low-pass filters (50-200 Hz, 12 dB/octave)
  • variable bass boost (0-12 dB at 40 Hz)
  • Class AB amp technology
  • differential-balanced inputs eliminate noise from your vehicle's electrical system
  • preamp and speaker-level inputs
  • speaker-level inputs (require speaker wire to RCA adapters)
Other Features
  • 8-gauge power and ground leads and a 40-amp fuse recommended — wiring and hardware not included with amplifier
  • no onboard fuses — when installing multiple amps in a system, an additional 40-amp in-line fuse between the distribution block and the amplifier is recommended
  • 8-3/16"W x 2-3/8"H x 7-1/8"D
  • warranty: 2 years (extends to 3 years when purchased with a Kicker 8-gauge amp kit or multi-amp kit)
  • Our 60-day money-back guarantee
  • MFR # 41DXA1252

What's in the box:

  • Two-channel amplifier
  • Four 3/4" #8 self-tapping screws
  • Owner's Manual

Customer reviews

Loading reviews...

Kicker DXA125.2 reviews

Average review:

6 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

Product Research

Features
Controls
Installation
Connections

Features

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured over the full frequency range of the amp with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels at a reference of 1 watt. CEA-2006 allows consumers to compare car amplifiers and receivers on equal footing. Measured under CEA-2006 conditions the Kicker DXA125.2 is rated at 30 watts RMS x 2 channels into a 4-ohm load and the signal to noise ratio is >95 dB. Additional specs listed in the manual (but not listed as CEA-2006 compliant) include 60 watts RMS x 2 channel into a 2-ohm load (measured using a 14.4 volt power supply with no more than 1% THD+N) and 95 dB signal-to-noise ratio (measured at the rated power output).

Auto Turn-On: There are two ways to automatically turn on the amplifier. Most aftermarket car stereo head units will have a remote turn-on lead, which can be extended to the amplifier location and connected to the amp's Remote terminal. If connecting the amplifier to a factory stereo, or a head unit without a remote turn-on lead, the amp can automatically turn on using the DC Offset mode. The amp detects a 6-volt DC surge on the signal inputs and turns the amplifier on. There is no switch on the amp to select the Turn-On method.

Protection Circuitry: The DXA125.2 has protection circuitry that will turn the amp off in the event of overheating, over voltage (over 16 volt input), under voltage (under 10 volt input), and short circuit (speaker output). If the Protection LED on the right side of the amp illuminates red, the protection circuit has engaged and the amp will not play until the problem is resolved.

Dual Input Sensitivity: The DXA125.2 can receive low- or high-level signals from your car stereo source unit at the amplifier's left and right RCA inputs. The low-level signal can be sent from the source unit's RCA line-level outputs. In this case, the Input Sensitivity switch on the amp should be set to "LO". A high-level signal can come from the source unit's speaker outputs, and connected to the amplifier using the Kicker KISL adapters. The Input Level switch should be set to "HI".

Fail-Safe Integration Technology (FIT): FIT utilizes isolated differential inputs, rejecting noise and electrical interference for the quietest operation possible. FIT also allows Kicker amps to accept output from nearly any factory or aftermarket head unit.

Stereo-and-Mono-Simultaneously (SAMS): The amp has the capability of powering a pair of full-range speakers and a mono subwoofer from one pair of channels. Using passive crossovers, you can high-pass the signals to the full-range speakers and to low-pass the signals to the subwoofers. The SAMS wiring diagram can be found in the Owner's Manual.

Controls

Input Level: The DXA125.2 has a two position (in/out) switch to set the input level type. It can be pressed in for High (for speaker level) or set to out for Low (for line level).

Gain: The input gain is continuously variable, labeled 0 to 11. The gain range is governed by the input level switch: 250mV to 10V for speaker level (HI) and 125mV to 5V for line level (LO). A small screwdriver is needed to adjust the gain.

Crossover Frequency: The crossover can be set for low-pass (LO), high-pass (HI), or full-range operation (OFF). The crossover frequency range is continuously variable between 50 Hz and 200 Hz. The crossover slope is 12 dB per octave  A small screwdriver is needed to set the crossover cutoff frequency.

KickEQ Bass Boost: The KickEQ bass boost circuit provides a signal boost centered at 40 Hz. The bass boost is continuously variable between 0 and 12dB. A small screwdriver is needed to adjust the amount of bass boost.

Installation

Wiring Recommendations: Kicker recommends that the amplifier be connected to the vehicle's battery using 8 Gauge power and ground wiring. An external 40 amp fuse should be installed on the power wire within 18" of the battery. There are no fuses included or built into the amplifier.

Kicker Extended Warranty Offer: Kicker will extend the amp's standard warranty by an additional year (for a total warranty of three years) when it is installed with a qualifying Kicker amplifier installation kit. Kicker recommends the PK8, CK8, or ZCK84 wiring kit for this amp. The amplifier and installation kit must be purchased from an authorized Kicker dealer.

Connections

Left Side of Amplifier:

  • GND (ground): screw terminal; accepts spade connector up to 0.5" wide
  • REM (remote turn-on): screw terminal; accepts spade connector up to 0.33" wide
  • +12V (power): screw terminal; accepts spade connector up to 0.5" wide
  • Speaker Outputs: two pairs of screw terminals; accepts spade connectors up to 0.32" wide

Right Side of Amplifier:

  • RCA Inputs: one pair of RCA jacks, used for line level or speaker level inputs with KISL

Loading accessories...

Customer Q&A

Q
Crutchfield asked: Why did you buy this?
A
Lots of power. [ James  May 01, 2016 ]
A
I was looking for a amplifier for speakers that I had purchased from Crutchfield. [ Richard  Apr 05, 2016 ]
A
Decently priced [ Austin  Apr 02, 2016 ]

2 questions already asked

Q
How do I wire 4 door speakers to this amp?
[ rafael  Feb 13, 2017 ]
1 answer
A
I only run 2 subs does it have 2 or 4 channel output ?
[ Chart  Feb 13, 2017 ]
Q
I am using this to power a pair of 5.25 (kicker) in the front doors. My question is would this amp be stable under a 2 ohm load if I wired a pr. of tweeters in for the front doors? Thx in advance for the help
[ chris  Sep 28, 2016 ]
1 answer
A
Usually Tweeters use a capacitor to filter out lower frequencies. I have had similar setups with other amplifiers without any issues. Personally I do not see you having any issues adding tweeters in parallel to the 5.25 speakers.
[ HECTOR  Sep 29, 2016 ]

Loading articles...

TOP