About the MTX SS7
Signed, sealed, delivered
Signed, sealed, delivered
MTX built their Signature Series speakers to give you great sound. Period. The SS7 component system begins with the 6-1/2" woofer, which features a glass fiber/paper cone housed in a non-resonant cast-aluminum basket for maximum accuracy. The cone's stiffness-to-weight ratio allows the woofers to deliver strong output, even when you're using a smaller amp or your car stereo's built-in power. You can mount the system's water-resistant teteron tweeters inside door panels or pillars without worry about moisture damage.
This rugged 6-1/2" woofer is ready to rock.
MTX designed the system's 2-way crossover for ease of installation, with pre-wired connections for the woofer and tweeter. Its small size allows a variety of mounting options. You can choose between two tweeter levels (flat and -3 dB) so the highs will be balanced with the rest of your music. You can use screws or zip ties to mount the crossover, or you'll also find a threaded rear insert which allows blind mounting inside the door panel—out of sight and out of the way.
The SS7 system offers high-fidelity sound reproduction, with real-world features that make installation much easier. Hear the greater clarity and definition that these quality speakers can bring to your vehicle.
Installation note: You'll need a pair of our universal backstraps to install the tweeters in the factory locations.
- component speaker system includes 2 woofers, 2 tweeters, and 2 crossovers
- 6-1/2" glass fiber/paper cone
- 1-3/16" teteron tweeter
- cast-aluminum basket
- 2-way crossover (12 dB per octave at 2800 Hz)
- power range: 15-150 watts RMS (300 watts peak power)
- frequency response: 31-30,000 Hz
- sensitivity: 85.4 dB
- impedance: 4 ohms
- woofer mounting depth: 2-7/8"
- woofer grilles included
- warranty: 2 years
- Our 60-day money-back guarantee
- MFR # SS7
What's in the box:
- 2 Woofers
- 2 Tweeters (with 7" wire attached)
- 2 Crossovers
- 2 Woofer grilles
- 2 Tweeter grilles
- 2 Flush mount tweeter housings (with tweeters installed)
- 2 Surface mount tweeter housings
- 2 Angled mount tweeter housings
- 2 Metal flush mount tweeter clamps
- Tweeter removal tool
- Two M4x35mm Pan-head machine screws
- Two M4x7.5mm Pan-head machine screws
- Sixteen 1" Pan-head self-tapping screws
- 8 Pieces of grille putty
- 16 Speed clips
- Warranty information
Thanks for submitting your review
More details on the MTX SS7
Features & specs
|Speaker Size||6 1/2|
|Tweeter Design||1-3/16" Dome|
|Parts Warranty||2 Years|
|Labor Warranty||2 Years|
|Sensitivity (1W at 1 meter)||85.4|
|Sensitivity at 2.83 volts||N/A|
|Frequency Response||31 - 30k Hz|
|Minimum RMS Wattage||15|
|Maximum RMS Wattage||150|
|Peak Power Handling (Watts)||300|
|Top-mount Depth (Inches)||2 7/8|
|Bottom-mount Depth (Inches)||N/A|
|Cutout Diameter or Length (inches)||5 9/16|
|Mounting Height (Inches)||0.36|
Crossovers: The input and output wires (12") are attached to the crossovers. The output wires are terminated with quick slides, so they easily plug into the woofers and tweeters. There are two tweeter output options, flat and -3 dB. The crossovers are round, approximately 3-3/4" diameter and 1-3/8" tall. The crossover slope is 12 dB/octave and the crossover point is 2.8 kHz. While not waterproof, the crossovers are in closed casings, so mounting them in the doors should not present any moisture problems.
Woofers: The combination paper and glass fiber cone has a high stiffness to weight ratio, maintaining a detailed output and keeping the damping characteristics of the paper.
Tweeters: The tweeters are 30mm (1-3/16") Teteron soft domes. They can be flush mounted, angled mounted (semi-flush), or surface mounted.
|Frame Diameter||Cutout Diameter||Mounting Height||Mounting Depth|
|Angled Mount||2.112" x 2.228"||1.86" x 1.52"||0.93"||0.625"|
|Surface Mount||2.125"||N/A||1.175"||Screw depth|
Q Crutchfield asked: Why did you buy this?