About the MTX T610X3D
Looking for the perfect mate for your Class D mono subwoofer amp? MTX's T610X3D enclosure comes loaded with three Thunder6000A 10" dual voice coil subwoofers, and its 2-ohm total impedance (the three dual voice coil subs are wired in parallel) maximizes the output capability of any compatible amp.
The Thunder6000A subs combine an aluminum-coated, mica-filled polypropylene cone, oversized magnet structure, and rubber surround for powerful bass and serious power handling (up to 750 watts RMS). Its trapezoidal shape allows it to fit into many vehicles even tough-to-fit Camaros and Firebirds. The attractive charcoal carpeting and the stylin' rear Plexiglass window give the enclosure a custom-built appearance.
Note: Since this enclosure is wired for 2-ohm total impedance, make sure that your amp is compatible. Most car amplifiers are stable down to 2 ohms in standard mode, or 4 ohms in bridged operation.Details:
- three 10" dual voice coil Thunder6000A woofers
- wired for 2-ohm total impedance
- sealed enclosure with charcoal carpet and rear window
- frequency response 46-150 Hz
- power handling 150-750 watts RMS
- peak power handling 1500 watts
- sensitivity 90 dB
- 35-1/8"W x 13-3/16"H x 5-1/8"D(top) x 14-7/16"D (bottom)
- 2-year warranty (on speakers)
Thanks for submitting your review
More details on the MTX T610X3D
Features & specs
|Woofer Size (inches)||10 x 3|
|Speakers Per Box||---|
|Woofer Material||Mica-filled poly|
|Pieces in System||1|
|Connector Type||5-way post|
|Frequency Response||46-150 Hz|
|Power Range (Watts RMS)||750|
|Parts Warranty||2 Years|
|Labor Warranty||2 Years|
Angled Front And Back Panels: The enclosure's back panel and front panel are angled at 70 degrees, resulting in a greater depth at the bottom of the enclosure than at the top. The angled design allows the enclosure to fit nicely against the back of the angled rear seat of most cars.
Wiring Configuration: This enclosure is loaded with three 10" dual voice coil woofers and has a single terminal cup with 5-way binding posts. The woofers are wired together in a parallel configuration, resulting in a 2-ohm load.
Mica-filled Polypropylene Cones: Each woofer cone is made of Mica-filled poly with a bright aluminum finish and 8 stiffening ribs for improved cone stiffness and higher mechanical power handling. Concentric rings are molded into the cone and dust cap surfaces to give them a machined appearance. The "MTX Audio" is embossed on the poly dust caps.
NBR Surrounds: Each woofer is made with a one-piece NBR (Nitrile Butadiene Rubber) surround and gasket combination. When bottom-mounting the woofer, the one-piece surround and gasket make an air-tight seal, to prevent any loss of performance due to air leaks around the woofer. When the woofer is top-mounted, the one-piece surround and gasket combination enhances the overall cosmetic appearance of the woofer. NBR has the added benefit of being resistant to ozone and UV rays for extreme durability.
Oversized Magnet Structure: Each woofer has an oversized (37 oz.) magnet structure, with a 2" voice coil.
Asymmetrical Linear Drive: This system improves linearity and permits high output with low distortion.
Spider Plateau Venting: Heat from the voice coil is vented through metal-mesh covered vents that surround the back of the spider.
5-way Binding Posts: The enclosure has one set of gold-plated 5-way binding posts that will accept bare wire, pin connectors, spade lugs, banana plugs, and dual banana plugs.