About the MTX Thunder681
Speakers for the real world
Speakers for the real world
MTX doesn't make speakers that only deliver the goods in a sound lab. This Thunder681 component system features a durable 5”x7"/6"x8” polypropylene woofer with a rubber surround that'll shrug off the weather and wear that come with living in your car full-time. You can swivel the 1-3/16" soft dome tweeter up to 15 degrees in your direction to really dial in the stereo imaging across your dash, and MTX includes hardware to flush- or surface-mounting.
The included crossover network features 2-level tweeter adjustment for fine-tuned sound staging. And, while no car speaker can produce bass like a large subwoofer, the Thunder681 woofers truly shine in the lower frequencies. With up to 90 watts RMS of power handling, you can add to their impressive depth and richness when you power them with an outboard amplifier.
Installation note: You'll need a pair of our universal backstraps to install the tweeters in the factory locations.
Grilles are not included; the factory grilles should be suitable for most applications.
- component speaker system includes 2 woofers, 2 tweeters, and 2 crossovers
- 5"x7"/6"x8" polypropylene cone with rubber surround
- 1-3/16" silk soft dome tweeter
- 2-way crossover with adjustable tweeter level
- power range: 2-90 watts RMS (180 watts peak power)
- frequency response: 46-20,000 Hz
- sensitivity: 90 dB
- impedance: 4 ohms
- woofer mounting depth: 2-1/2"
- grilles not included
- warranty: 2 years
- Our 60-day money-back guarantee
- MFR # THUNDER681
What's in the box:
- 2 Woofers
- 2 Tweeters (7" wire attached)
- 2 Crossovers
- 2 Woofer bottom mount brackets
- 2 Surface mount tweeter housings (with tweeters installed)
- 2 Flush mount backing rings
- 2 Flush mount trim rings
- 2 Foam tweeter spacers
- Four 6" Speaker wires (each with quick slide terminals on one end and bare wire on the other)
- 2 Tweeter flush mounting clips
- Two M4x35mm machine screws
- Four 3/4" Flat-head screws
- Twelve 1" Self-tapping screws
- 12 Speed clips
- Cardboard template
- Mounting diagram
- Warranty information
See the difference between "Open Box" and "Scratch & Dent" Outlet items
MTX Thunder681 reviews
Thanks for submitting your review
More details on the MTX Thunder681
Features & specs
|Tweeter Design||30mm Dome|
|Parts Warranty||2 Years|
|Labor Warranty||2 Years|
|Sensitivity (1W at 1 meter)||N/A|
|Sensitivity at 2.83 volts||90|
|Frequency Response||46 - 20k Hz|
|Minimum RMS Wattage||2|
|Maximum RMS Wattage||90|
|Peak Power Handling (Watts)||180|
|Top-mount Depth (Inches)||2 1/2|
|Bottom-mount Depth (Inches)||2 11/16|
|Cutout Diameter or Length (inches)||0|
|Mounting Height (Inches)||0.356|
Woofer Cones: The MTX Thunder Series speakers feature durable and rigid polypropylene woofer cones. Polypropylene is also resistant to the moisture and temperature extremes found in automotive applications.
Mounting Applications: MTX describes this speaker as a 6x8/5x7; it fits examples of both applications, but the hole spacing is not a perfect match for Ford 6x8 applications. Drilling new screw holes or inserting the screws at a sharp angle may be necessary. Please check the Crutchfield Vehicle Selector to confirm fit.
Tweeter Mounting Options: The tweeters can be flush mounted or surface mounted using the included hardware. Once installed in either housing, the tweeter will pivot approximately 15° in any direction.
|Frame Diameter||Cutout Diameter||Mounting Height||Mounting Depth|
|Surface Mount||2.2"||N/A||1.035"||0.64" (Screw Depth)|
Crossovers: The crossover inputs and outputs are set screw terminals; they accept bare wire up to 10 gauge. There are two positive tweeter outputs, offering flat and -3dB output options. The screw terminals have 2mm Allen heads, and are recessed slightly more than half an inch, so a standard Allen head bit for a screw driver will not fit (an Allen wrench is not included). The crossover point is 4 kHz, the high pass slope is 18 dB/octave and the low pass slope is 6 dB/octave.
- Width: 4-15/16"
- Height: 1-3/8"
- Depth: 3-1/8"
1 question already asked