About the ErgoAV ERMMX1-01B
Precisely position your TV
Precisely position your TV
The full-range ErgoAV ERMMX1-01B mount gives you plenty of options for positioning your TV. It can hold your TV just 4-1/8" from the wall, or extend it outward 24-1/4". You can swivel the TV left or right and tilt it up or down for optimal viewing. And after mounting, you can adjust it ±3 degrees to level it.
The mount requires dual-stud installation. It can accommodate either 16" or 24" spacing on-center. It can support a TV with a screen size 49"-90", weighing up to 132 lbs.
- fits most flat-panel TVs from 49"-90"
- supports up to 132 lbs.
- fits VESA mounting hole patterns 200 x 100mm to 800 x 600mm
- extends TV out to 24-1/4" from wall
- swivel range: 90° left or right
- tilt range: 5° up to 12° down
- level adjustment: ±3°
- dual-stud installation required
- accommodates 16" or 24" on-center installation
- mounting hardware included
- hook-and-loop ties to secure cables to arm
- dimensions (measured by Crutchfield): 37-11/16"W x 24-3/4"H x 3"D (with arm retracted)
- weight: 29.4 lbs.
- warranty: 5 years
- Our 60-day money-back guarantee
- MFR # ERMMX1-01B1
What's in the box:
ErgoAV ERMMX1-01B owner's manual
- Wall-plate bracket
- Arm Aseembly
- 2 TV brackets
- 2 End-caps
- Four M6x15mm bolts
- Four M6x35mm bolts
- Four M8x15mm bolts
- Four M8x25mm bolts
- Four M8x35mm bolts
- Four M8x50mm bolts
- Four M6/M8 washers
- Eight 2.5mm spacers
- Four 10mm spacers
- Four 22mm spacers
- Six 5/16" x 2-3/4" lag-screws
- 6 Concrete-anchors
- Instruction Manual
- Installation Template
Thanks for submitting your review
This review was collected as part of a promotion
More details on the ErgoAV ERMMX1-01B
Features & specs
|Mount Type||Wall Mount|
|Roll (Level) Adjustment||Yes|
|Wood Stud (Single)||No|
|Wood Stud (Dual, 16-inch)||Yes|
|Wood Stud (Dual, 24-inch)||Yes|
TV Compatibility: The ErgoAV ERMX1-01B full-motion wall-mount fits most 49" to 90" flat-panel TVs that weigh up to 132 lbs. The TV must also meet the following VESA and screw size requirements.
- VESA Sizes: 200x100 to 800x400
- Screw Size: M6 or M8
Note: Additional hardware may be required for your specific model of TV. For example; shorter or longer screws, thicker or slimmer washers or spacers. These additional accessories can often be found at your local hardware store.
Full-Motion Design: The full-motion wall-mount extends to position your TV up to 24.25" from the wall and retracts to position your TV only 4.125" from the wall. The mount can also swivel your TV left or right (+/- 90 degrees), as well as tilt (+5/-12 degrees) your television - making it possible for you to get the optimal viewing angle. The horizontal shift feature allows your mounted TV to be moved horizontally on the wall-plate bracket to allow optimal placement on your wall. A level adjustment (+/-3 degrees) allows the TV to be properly leveled after installation.
Note: The tilt and swivel adjustment ranges will vary based on the size of your television.
Integrated Cable Management: Its integrated cable nanagement system creates a neat and clean appearance, even when mount is fully extended.
Dual Stud Installation: The ErgoAV ERMX1-01B accommodates dual-stud 16" or 24" OC (on-center) installation, as well as concrete block installation using the included hardware and mounting template. The wood studs should measure 2" x 4", while the concrete block wall should be more than 5.5" thick. Tools required for installation include -
- Electric drill
- 7/32" bit (wood), 3/8" bit (masonry)
- 1/2" Socket-wrench
UL Certified: This product has been safety tested and UL Certified.