About the Alpine SWR-T10
What good is a shallow-mount sub if it doesn't move air? Alpine's Type-R Thin subwoofers combine low-profile design with high power handling to pump out powerful bass in your vehicle's hard-to-fit spaces. These shallow subs offer a mounting depth of less than 3.5 inches, but their cone excursion is nearly as long as that of their regular counterparts — you'll hear deep, satisfying bass from the resulting massive air movement.
Big bass, not much space
The special spider design uses a series of adjacent rolls to get the cone moving without requiring a lot of space, combining with the advanced motor structure that reduces the sub's profile while maintaining accuracy. A dynamic neodymium magnet structure allows the sub to handle more power than the typical shallow-mount sub.
Handles plenty of power
The SWR-T10 10" thin subwoofer handles up to 600 watts RMS for tremendous thump. Its aluminum cone works with the multi-roll Santoprene™ surround for performance that will really surprise you. The finned aluminum heat sink is directly coupled to the frame for rapid heat dissipation that'll keep your sub running cool. Type-R Thin subs present ideal solutions for applications with limited available space, such as pickup trucks and compact cars.
To drive this single subwoofer, we recommend a mono amplifier rated between 450 and 900 watts RMS at 4 ohms. For more information, please refer to our article on How to Match Subwoofers and Amplifiers.
- 10" 4-ohm shallow-mount subwoofer
- aluminum cone with Santoprene rubber surround
- cast aluminum frame with radial finned heat sink
- frequency response: 28-200 Hz
- power handling: 300-600 watts RMS
- peak power: 1,200 watts
- sensitivity: 83 dB
- top-mount depth: 3-1/4"
- grille not included
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # SWR-T10
What's in the box:
- One 10" Thin-mount (4-ohm) subwoofer
- Rubber trim-ring (installed)
- Application Guide (Eng/Fre)
- Customer Care Registration Card
- Limited Warranty Card (US/Canadad)
- Important Notice! (Eng/Fre)
Alpine SWR-T10 reviews
Paired this speaker with a 500 watt rms fosgate mono amp and after playing my stereo a few times the speaker went silent so i checked it with a ohm meter and found a infinite ohm reading or open circuit in the speaker .I Have the dual voice coil 350 watt r-series 8" alpine that i was upgrating from and that i am now going back to IT and it handles the 500 watt fosgate amp turned up gain control higher than the 10" that blew and thumps alot harder than the 10" subwoofer that blew and it sounds alot better than the 10" that blew . Maybe the 2 ohm dual voice coil is a better speaker or maybe i got a lemon when i bought this single 4 ohm voice coil . What ever the case i"m sticking with the dual voice coils and hope alpine has a replacement upgrade to replace the blow 10" . let you know in a future review how it was handled by crutchfield and alpine.
0 of 1 found this helpful
The other two reviews are dumb. Complaining about blowing a speaker with a 300-600w rms after pushing it with a 1000w for who knows how long... Smh. No doubt they turned the gain all the way up. Probably the frequency also haha. Just saying use your head. You can't always go off of reviews.
7 of 8 found this helpful
I had this hooked up to a Alpine m1000. I had it in a sealed box that was just the right size. I blew it in just a few weeks. I think it overheated. I then put my old swr-t12 and it worked like a champ for years until it was stolen. I'm now going to try the jl 12tw3.
Pros: Small size and great specs
Cons: Didn't live up to the hype or specs. Not worth the price at all.
1 of 16 found this helpful
Unless i'm underpowering this sub with a Alpine M-500, The speaeker is average. I was originaly using a Kicker compcvr 10, but i blew the sub. before i blew the kicker sub, it pounded better then the Alpine type R shallow mount subwoofer. gonna try and increase the power to a Alpine M-1000 to hopfully get the thump i once had before i blew my kicker sub.
28 of 130 found this helpful
More details on the Alpine SWR-T10
Features & specs
|Surround Material||Santoprene rubber|
|Ideal Sealed Box Volume (cubic feet)||0.42|
|Ideal Ported Box Volume (cubic feet)||0.75|
|Port diameter (inches)||N/A|
|Port length (inches)||N/A|
|Dual Voice Coil||No|
83 dB at 1 watt |
|Frequency Response||28 - 200 Hz|
|Max RMS Power Handling||600|
|Peak Power Handling (Watts)||1800|
|Top Mount Depth (inches)||3 1/4|
|Bottom Mount Depth (inches)||N/A|
|Cutout Diameter or Length (inches)||9 1/8|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Alpine Type-R Thin Subwoofer: The Alpine Type-R Thin subwoofer series combines the low-bass performance and power handling of Alpine's traditional Type-R subwoofers in a thin package optimized for extremely small enclosures. The new Type-R Thin boasts no less than 7 unique Alpine technologies in its industry-first design. These innovations allow the Type-R Thin to have the output and power handling of the traditional Type-R series in less than half the depth. The new Type-R Thin design has the same DNA of the standard Type-Rs; demanding cleaner, deeper bass extension, faster, more accurate transients, and even greater output capability.
Parabolic Aluminum Cone with Force Transfer Assembly: A Heavy-duty magnet assembly calls for heavy-duty cone materials, such as parabolic aluminum cone woofer. This specially engineered aluminum cone is reinforced by an injection-molded force transfer assembly, giving the cone structure outstanding stiffness while minimizing moving mass. A centering ring in the force transfer assembly is also engineered to lock the voice coil assembly in place. This makes the entire piston assembly extremely strong and linear.
FEA Optimized HAMR Surround: The High-Amplitude Multi Roll (HAMR) Surround Design allows for extreme excursions without sacrificing valuable cone area. FEA Optimized for linearity and made with injection-molded Santoprene , the HAMR surround is a key part of the suspension system that provides accurate, distortion-free control at extreme excursions.
1.5lb Neodymium Magnet with 4" Voice-Coil: The Type-R Thin subwoofer's 1.5lb neodymium magnet has 5x the magnetic strength than standard ferrite magnets used for most subwoofers. This powerful magnet combined with a massive 4" (100mm) voice coil delivers increased power handling and more accurate, louder, cleaner bass with even more control.
Segmented Spider Design: You can count on Type-R Thin subwoofer to deliver strong, impactful output like its predecessors. Its Revolutionary Segmented Spider Design provides the Excursion of a tall subwoofer. Most shallow-mount subwoofers have less output than traditional deep subwoofers, since their shallow frame limits how far their cones can move at high power levels. The Type-R Thin subwoofer uses Alpine's patent pending Pass-Through Gap Geometry, allowing the unique Thermoplastic Elastomer Segmented Spider to completely pass through the motor structure. This means the cone and voice coil assembly have the clearance needed for over 50mm of peak-to-peak excursion, allowing for massive output even in such a shallow frame.
FEA Optimized Dual-Sided Machined CRC Motor Structure: An FEA Optimized Dual-Sided Machined CRC Motor Structure creates a symmetrical magnetic field with evenly distributed flux density to greatly reduce distortion, while further improving power handling and output.
Radial Vented VC Heat Sink & Airflow Management System: Alpine's Patented Radial Vented VC Heat Sink and Airflow Management System (helps to minimize power compression and ensures reliable long playing time by actively pulling (or transferring) output-robbing heat away from the Voice Coil.
Cast Aluminum Frame: The new cast aluminum frame is directly coupled to the machined aluminum shorting sleeve assembly. This allows the entire frame to act as a heat sink for sustained power handling, even in the most extreme of applications.
Speaker Terminals: This Alpine Type-R Thin subwoofer features a pair of heavy-duty screw-terminals on one side of the woofer's basket that will accommodate up to 8-gauge speaker wire. A hex-key is provided to adjust the set-screw terminals.
Gasket Cover: Alpine uses a Concealed Mount Gasket System to cover the mounting screws for a clean look. The black rubber gasket ring comes already installed on the woofer and needs to be removed before drilling the mounting screws (not supplied). The gasket ring then snaps back into place once the woofer is mounted.
No Break-in Period: There's no need to play your sub for hours to break it in to achieve consistent performance. This sub is designed to deliver consistent performance right out of the box. Since this revolutionary design is made with an injection mold resin, rather than phenolic stiffened textile, this new spider requires no break-in to achieve ideal performance. A Co-Molded Aluminum collar attaches the voice coil to the spider to ensure a reliable, high-strength design.
Thin Mount: The Alpine Type-R Thin series subwoofer has been engineered to offer more installation flexibility and application versatility to build the ideal sound system. At 3-1/4" deep, this 10" sub provides deep bass performance where it normally couldn't fit. And the 0.35 cu/ft ideal sealed enclosure size (or 0.6 cu/ft ideal vented enclosure size) means great bass performance can go just about anywhere in your vehicle.
Recommended Sealed Box Volume: The recommended sealed box sizes range from 0.25 cu/ft to 0.5 cu/ft. Within this range, the ideal size is 0.35 cu/ft.
Recommended Vented Box Volume: The recommended vented box sizes range from 0.5 cu/ft to 0.75 cu/ft. Within this range, the ideal size is 0.6 cu/ft. A slot port with the following dimensions should be used: 3.625" (W) x 2" (H) x 24.5" (L).
Q Crutchfield asked: Why did you buy this?
2 questions already asked