About the Rockford Fosgate R2-200X2
Give your speakers the power they deserve
Give your speakers the power they deserve
Rockford Fosgate's Prime Series R2-200X2 amplifier can power two speakers with 50 watts RMS each, so you'll hear your music clearly over the noises of the wind and road. You could also use this amp in bridged, 1-channel mode to power a subwoofer with up to 200 watts RMS. High- and low-pass filters help you get maximum performance from the speakers in your vehicle.
Setting it up for optimum performance
Rockford Fosgate's C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) setup system ensures your music will sound as clean and powerful as possible. It's a simple system to use — turn it up until the light shows red, then turn it down until the red light goes out. Speaker-level inputs let you hook this amp up to almost any system, even a factory stereo.
- 2-channel car amplifier
- 50 watts RMS x 2 at 4 ohms
- 100 watts RMS x 2 at 2 ohms
- 200 watts RMS x 1 bridged at 4 ohms (4-ohm stable in bridged mode)
- CTA-2006 compliant
- Class-D amplifier design
- variable high- and low-pass filters (50-250 Hz, 12 dB/octave)
- C.L.E.A.N. gain setup system includes clip lights
- auto remote turn-on
- preamp and speaker-level inputs
- preamp outputs
- wiring, fuse, and hardware not included with amplifier
- 4-gauge power and ground leads and a 30-amp fuse recommended
- dimensions: 8-1/8"W x 2"H x 7-3/4"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # R2-200X2
What's in the box:
Rockford Fosgate R2-200X2 owner's manual
- 2-Channel amplifier
- One 7" Speaker input harnesses
- 3mm Hex key
- Four 3/4" Screws
- 4 Flat washers
- Installation and Operation instructions (English/ French/ Spanish/ German/ Italian)
- Certificate of Performance
- Rockford Fosgate contact information
Rockford Fosgate R2-200X2 reviews
Thanks for submitting your review
This review was collected as part of a promotion
More details on the Rockford Fosgate R2-200X2
Features & specs
|RMS Power Output (Watts x Channels)||
50 x 2 |
|Peak Power Output (Watts x Channels)||N/A|
|Power at 2 Ohms (Watts x Channels)||100 x 2|
|Bridged Power (Watts x Channels)||200 x 1|
|Minimum Impedance Bridged||4|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||20-20k Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||80 dB|
|Low-Pass Crossover Frequency||50-250 Hz|
|Low-Pass Slope (dB/octave)||12 dB/octave|
|High-Pass Crossover Frequency||50-250 Hz|
|High-Pass Slope (dB/octave)||12 dB/octave|
|Bass Boost Frequency||N/A|
|Speaker Level Inputs||Yes|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Overview: The Rockford Fosgate Prime R2-200X2 is a 2-channel full-range Class D amplifier. The amp is bridgeable, so it can be wired as 2-channel or 1-channel.
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring amplifier power uses a DC input voltage of 14.4 volts and the RMS power output is measured over a frequency range of 20 Hz to 20 kHz (for full range amplifiers), with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4 ohms. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples).
- Power Output: 50 watts RMS x 2 into 4Ω
- Signal to Noise Ratio: >80 dBA (measured at 1 watt into 4Ω)
- Power Output:
- 2Ω: 100 watts RMS x 2 (14.4 volts)
- Bridged: 200 watts RMS x 1 (14.4 volts, 4Ω)
Mounting: The amplifier can be mounted vertically, horizontally, or inverted using the supplied mounting screws; horizontal mounting (right side up) will provide the best cooling.
Gain: The rotary gain control is labeled 0 to 11, equivalent to 150mV-4V line level or 450mV-12V speaker level.
Crossover: Using the 3-position crossover switch, choose low-pass, all-pass, or high-pass. The low-pass and high-pass crossovers are 12 dB per octave Butterworth.
Frequency: The crossover point is set with a rotary dial; it is continuously variable from 50-250 Hz.
Auto Turn-on Switch: When using speaker level inputs, this switch can be set to On and the amp will turn on when it senses an input signal (DC offset on the left input). When using the RCA inputs a remote turn-on wire must be connected.
Power Terminals: The power and ground terminals are nickel-plated set-screw terminals, and will accommodate up to 4-gauge wire. The set screws are tightened/loosened with the included 3mm hex key.
Fuses: The amplifier does not have on-board fuses. A 30-amp fuse should be placed on the power wire within 18" of the battery.
Remote Turn-On Terminal: The remote turn-on terminal is a nickel-plated set-screw terminal that will accommodate up to 8-gauge wire. The set screw is tightened/loosened with the included 3mm hex key.
Speaker Terminals: The speaker terminals are nickel-plated set-screw terminals that will accommodate up to 8-gauge wire. The set screws are tightened/loosened with the included 3mm hex key.
RCA Input: There is one pair of RCA input jacks. The balanced differential inputs are nickel-plated to resist signal degradation caused by corrosion.
RCA Pass-Thru: A pair of nickel-plated RCA pass-thru jacks provide a convenient way to connect an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the amplifier location. The signal from the inputs is passed directly to the RCA outputs.
Speaker Level Inputs: There is a port for the included speaker input harness. If speaker level inputs are used, nothing should be connected to the RCA jacks.
The Rockford Fosgate R2-200X2 replaces these items
- 150 watts RMS x 1 bridged
- variable high- and low-pass filters
- preamp and speaker-level inputs; preamp outputs
2 questions already asked
Great amp. Strong bass and easy hook up. The auto on makes the install a breeze for my application.
Clifford from Delaware, OH