About the Kenwood KDC-C719
Load up Kenwood's KDC-C719 with 10 of your favorite CDs, CD-Rs, or CD-RWs and hit the road. Just connect this CD changer to the changer input on the back of your Kenwood in-dash receiver and you'll be cruising for hours to non-stop music.
The KDC-C719's Quad 1-bit Digital-to-Analog Converter ensures superior musical resolution and detail. CD Text will display on a compatible receiver, and you can name up to 100 of your favorite discs. The changer may be mounted at 0°-5°, 45°-50°, or 85°-90° angles.Details:
- plays CDs, CD-Rs and CD-RWs
- oil-damped suspension
- Integrated Quad 1-Bit Digital-to-Analog Converter
- disc naming up to 100 discs with compatible Kenwood receiver
- CD Text display (with encoded discs) on compatible receiver
- disc naming for 100 discs (with compatible receiver)
- mounts horizontally, vertically, and at 45 degrees
- CD frequency response 5-20,000 Hz
- CD signal-to-noise ratio 100 dB
- 16-foot connection cable included
- 10-1/8"W x 3-1/4"H x 7-3/16"D
- warranty: 1 year (new stock); 90 days (refurbished)
What's in the box:
- Silver 10-Disc CD changer with 3 transport screws and attached transport screw note
- One KCA-M112 10-disc magazine with attached caution sheet
- 16' Changer control cable (13-pin male connector on each end)
- 2 Plastic mounting brackets
- 4 Self-tapping screws
- 4 Machine screws (each with a flat washer and a lock washer)
- Instruction Manual
- Warranty Card
- Changer Control Cable Caution note
Kenwood KDC-C719 reviews
Thanks for submitting your review
More details on the Kenwood KDC-C719
Compatibility: This changer is compatible with Kenwood changer controllers made in 1998 and later. There is no O-N switch, so it cannot be connected to pre-1998 controllers.
Digital Optimum Servo Control (DOSC): This circuitry enables the CD changer to determine each disc's reflection rate and the modulation rate of its pits, enabling the changer to set the ideal servo gain for each disc. DOSC also adjusts servo gain and balance when it encounters vibration, scratches, dust, or fingerprints, reducing mistracking and skipping.
Precision Digital Timing (DPAC): A high-precision master clock circuit that is isolated from signal-processing circuits to eliminate interference. This ensures that digital information is processed at exactly the same rate as it was recorded, eliminating jitter (time-based errors that make music sound harsh).
Digital Filter: This unit has an 8-times oversampling digital filter, which is a circuit that removes most of the unwanted digital data from a digital audio waveform while it's still in the digital form. This allows the use of much gentler, better sounding analog filters when the digital waveform is converted back to an analog music signal.
Integrated Quad 1-Bit Digital-to-Analog Converter: Four digital-to-analog converters, two for each channel, improve playback sound quality, including musical detail and resolution. Using two converters for each channel reduces distortion by half.
Anti-Vibration Disc Transport: The disc transport mechanism uses soft butyl rubber insulators for exceptional shock resistance, along with ceramic-injected silicon oil that absorbs jarring vibrations even at extreme temperatures, reducing skipping and mistracking.
CD Compatibility: This unit will play prerecorded CDs, finalized CD-R discs, and finalized CD-RW discs.
CD Text: When playing CD Text encoded CDs, this changer will transmit the data for display on compatible Kenwood head units equipped with CD Text display capability.
Disc Naming: When used with a compatible head unit, the changer allows Disc Naming for 100 discs and up to 12 characters for each disc name.
Mounting Angles: You can install this changer at a 0-5 degree, 40-50 degree, or 85-90 degree angle. There are angle switching dials on both sides of the unit that must be set to agree with the mounting angle of the unit. Note: The supplied mounting brackets are for horizontal and vertical mounts only relative to the surface the changer is mounted to. Mounting the changer at a 40-50 degree angle requires mounting the changer to a flat surface, angled at 40-50 degrees, using the brackets in the horizontal position.
Dimensions: The changer dimensions at each mounting angle are as follows:
|Measurements (including brackets)||Horizontal