Contact us
Close contact box

Channel Master 3080

Antenna chimney mount

Item # 6593080

Top Seller

Item # 6593080

In Stock
Add to wishlist

About the Channel Master 3080

The 3080 chimney-mount kit includes a pair of "Z-type" mounts that provide 3 inches of clearance from your chimney. This kit accepts masts up to 1-1/2" in diameter.

Product highlights:


What's in the box:

  • 2 Z-type chimney brackets
  • 2 U-bolts
  • Two 12' Chimney straps (metal)
  • 4 Strap buckles
  • 4 Strap holders
  • 8 Nuts
  • Mounting diagram on packaging

Customer reviews

Loading reviews...

Channel Master 3080 Reviews

Average Customer Review(s):

Verified customer (What's this?)
Verified employee purchase (What's this?)



Crutchfield response

More details on the Channel Master 3080

Mark G.

Product Research


Overview: The Channel Master CM-3080 is used to secure the antenna mast to a chimney. Two brackets are included to anchor the mast at two different points, as far apart as the chimney will allow. The brackets will accommodate antenna masts with an outer diameter up to 1-1/2 inches. The center of the antenna mast is held 3.8" from the chimney. Two 12' metal straps are included.

Loading accessories...

Customer Q&A

Crutchfield asked: Why did you buy this?
Better price than Walmart and Crutchfield didn't make me sign up for an account. [ Richard  Nov 04, 2017 ]
because of the high prices of cable and the excellent reception i receive with the over the air antennae i purchased from Crutchfield. [ Mark  Dec 21, 2016 ]

1 question already asked

Exactly how do you attach the strap to the strap clamp?
[ Peter  May 15, 2014 ]
4 answers
Peter, It's admittedly a bit tricky. I highly recommend you have a friend assist and you should consider wearing gloves. The instructions are on the channel master support website. Just google the model. I would have included the direct link here but the form does not permit it. Basically consider the galvanized strap similar to a fabric one where you slip it through the clamp. Be careful not to tighten the clamp until you are confident you have pulled it to the proper tension. Once you tighten the clamp there's no way to loosen it to try again. Hope that helps! Colleen
[ COLLEEN  May 16, 2014 ]
To add to my comment. The last step is to fold the strap back over the clamp away from the eyebolt. Then trim excess strap leaving about an inch overhang. Sorry about that!
[ JOEL  May 16, 2014 ]
Unroll about a foot of strap. Slide the clamp down the strap with the tabs pointing up toward the eyebolt. Slide the strap though the eyebolt and fold over itself. Slide the clamp over the folded strap up against the eyebolt. It also helps to first use your pliers or channel locks to flatten the strap close to the eyebolt to get the clamp as close to the eyebolt as possible. Now crimp the flat part of the clamp with pliers or channel locks leaving the other flaps up. Fold the strap back over the clamp across the eyebolt. Flatten the the two flaps sticking up over the strap and and crimp. Trim off any excess strap leaving about an inch of strap after the clamp. Hope this helps.
[ JOEL  May 16, 2014 ]
Put the clamp right next to the tensioning screw. I put mine too far away and it just slips on the strap when tension is applied. Slide strap through clamp, then through the tension screw, then back through the clamp. I didn't see any instructions, so I'm irritated about that, unless they fell out. I'd like to see comments from others.
[ Johnny  May 16, 2014 ]

Loading articles...