Contact us
Close contact box

Sound Ordnance™ M-1350

Mono subwoofer amplifier — 350 watts RMS x 1 at 2 ohms

Item # 777M1350

Win the battle for great sound in your ride.

Win the battle for great sound in your ride.

Need help?
Contact our Virginia-based experts.
Discontinued item
5 questions - 8 answers

Item # 777M1350

About the Sound Ordnance™ M-1350

Win the battle for great sound in your ride. Sound Ordnance amplifiers feature tough construction, rugged looks, and a 3-year warranty, so you can enjoy the full power of your music for the long haul. Even better, you can add Sound Ordnance to your arsenal at a surprisingly affordable price.

Win the battle for great sound in your ride. Sound Ordnance amplifiers feature tough construction, rugged looks, and a 3-year warranty, so you can enjoy the full power of your music for the long haul. Even better, you can add Sound Ordnance to your arsenal at a surprisingly affordable price.

The Sound Ordnance M-1350 mono subwoofer amplifier packs a 350-watt wallop that'll give your subwoofers some serious firepower. An adjustable low-pass filter and a variable bass boost allow you to control your bass barrage at will.

The M-1350 amplifier uses sophisticated power supply and output technologies to ensure clean amplification from the input all the way to your speakers. Special circuits protect the amp from overheating and short circuits, and a turn-on delay virtually eliminates that annoying thump when you turn your system on.

Confused about impedance? Check out our article on matching subs and amps.

READ LESS

Product highlights:

  • mono subwoofer amplifier
  • 210 watts RMS x 1 at 4 ohms (350 watts RMS x 1 at 2 ohms)
  • variable low-pass filter (40-300 Hz, 12 dB/octave)
  • variable bass boost (0-12 dB, at 45 Hz)
  • variable subsonic filter (10-40 Hz)
  • PWM (pulse width modulation) power supply with MOSFET output
  • preamp inputs and outputs
  • fuse rating: 25A x 2
  • 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
  • 13-5/16"W x 2-1/8"H x 9-13/16"D
  • warranty: 3 years
  • Our 60-day money-back guarantee
  • MFR # M1350

What's in the box:

  • Mono amplifier with two 25A ATC blade fuses inserted
  • Spare 25A ATC blade fuse
  • 4 Self-tapping screws (5/8" length)
  • 4 Split lock washers
  • 4 Flat washers
  • Remote bass control module
  • 16.5' Remote bass control cable (with 6-pin RJ25 modular phone plugs on each end)
  • 2 Self-tapping screws (3/8" length)
  • 2 Small split lock washers
  • Owner's Manual

Featured video:

Customer reviews

Loading reviews...

Sound Ordnance™ M-1350 reviews

Average review:

100 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

Product Research

Features
Connections

Features

Power Ratings: The Sound Ordnance M-1350 is a mono-block Class AB amplifier with an RMS power rating of 210 watts per channel into 4 ohms, and 350 watts per channel into 2 ohms.Power ratings are measured with an input power of 14.4 volts.

Crossovers: The M-1350 is equipped with a low-pass crossover and a subsonic filter. You can set the low-pass cutoff frequency between 40Hz and 300Hz. The subsonic filter, designed to block ultra low frequencies that can damage speakers and rob amplifier power, is variable between 10Hz and 40Hz. The crossovers have a 12dB per octave slope, and cannot be turned off.

Bass Boost: The amplifier has a rotary bass boost control, which is continuously variable from 0dB to +12dB at 45 Hz.

LED Indicators: The M-1350 features two LED indicators: a green LED that illuminates when the amp is powered on, and a red LED that illuminates when the amplifier is in protect mode due to overheating or a short circuit in the speaker wire.

Remote Bass Control: The amplifier comes with a remote bass control module to allow you to adjust the volume of the amp from the front of the vehicle. The module has a rotary volume control knob, and an LED to indicate when the amplifier is turned on. The module is designed to mount under the dash, and comes with 16-1/2 feet of cable.

Connections

Removable End Caps: The end caps on the M-1350 are removable with a 3mm Allen wrench (not supplied) to make it easier to attach the power and speaker wires.

Power Connections: The power and ground connections are set screw terminals that will accommodate up to 8-gauge wire. (An 8-gauge amplifier wiring kit is recommended.) The remote turn-on terminal is a set screw terminal that will also accept up to 8-gauge wire. A Phillips-head screwdriver (not supplied) is required to tighten/loosen the terminals.

Speaker Connections: The speaker connections are set screw terminals that will accommodate up to 8-gauge wire. Even though this is a mono amplifier, there are two sets of speaker outputs. The terminals are wired in parallel internally, allowing you to connect two 4-ohm speakers to separate terminals. A Phillips-head screwdriver (not supplied) is required to tighten/loosen the terminals.

RCA Inputs and Outputs: The amplifier features a pair of stereo RCA inputs for connecting your head unit. There is also a pair of stereo RCA outputs for feeding the preamp signal to another amplifier, if needed.

Fuses: The M-1350 features two 25-amp ATC blade fuses.

Loading accessories...

Customer Q&A

5 questions already asked

Q
Ok. This may be a stupid question but I'm new to this. So can a mono sub amp power two subs? Or do I need a two channel amp because I have 2 subs?
[ Chase  Nov 05, 2015 ]
4 answers
A
Yes you can hook up multiple subs to the mono amp. Look up a wiring diagram so you can wire the subs for the ohms you want - this gets a little complicated when you have dual voice coil subs. I believe Crutchfield has some diagrams. - by the way this amp is a great value and packs a lot of power - enjoy!
[ MITCHELL  Nov 06, 2015 ]
A
It can power 2 just follow directions on running 2.
[ mike  Nov 06, 2015 ]
A
Yes you should have one channel per sub woofer. So a 2 channel sub is necessary for 2 subs. Or 2 mono amps, 1 per subwoofer. If you choose a 2 channel amp make sure each channel has the proper (watts) for the sub woofers.
[ JOHN  Nov 06, 2015 ]
A
The answer is yes, you should have a two channel amp for two sub woofers. A mono amp will only have one channel for outputs. This means there is only one pair, positive and negative, of output ports to go to a speaker or sub. A two channel amp will have 2 sets of plugs each providing power to the sub that is hooked up to that port.
[ JOHN  Nov 06, 2015 ]
Q
If the amp is powering a 4ohm subwoofer will the amp work on 2 ohms or 4 ohms?
[ Liam  Aug 30, 2015 ]
1 answer
A
4 Ohms but if the sub were 2 ohms the amp would produce 2 ohms
[ johnny  Aug 31, 2015 ]
Q
could i use this product with a Rockford Fosgate Prime R1-1X10 sub woofer?
[ Patrick  May 15, 2015 ]
1 answer
A
Thanks for your question. For information on selecting the best amp for your subs I would recommend reaching out to an Advisor by phone (1-800-324-9695) or online chat. They will be able to help determine the differences between the amp models and help you make the best choice for your system.
[ Krissy  May 19, 2015 ]  Staff
Q
How well will this power a single JL Audio 10TW3-D4?
[ Tim  Apr 11, 2015 ]
1 answer
A
Thanks for your question. For information on selecting the best amp for your subs I would recommend reaching out to an Advisor by phone (1-800-324-9695) or online chat. They will be able to help determine the differences between the amp models and help you make the best choice for your system.
[ Krissy  Apr 12, 2015 ]  Staff
Q
If I bought this to power a KICKER 10TCVT82 R TCVT8 SINGLE COMP 8 SUB 2 OHM BOX, would it be a good match?
[ Corey  Jul 01, 2014 ]
1 answer
A
Yes, this should be plenty of power to move an 8" subwoofer in a sealed enclosure.
[ ADAM D  Jul 02, 2014 ]
SHOW MORESHOW LESS

Loading articles...

TOP