About the Mackie 802VLZ4
Past to the future
Past to the future
The phenomenal success of Mackie's line of mixers is no accident—it's the result of 40 years of experience producing and selling some of the world's most popular mixers and sound reinforcement equipment. Now, Mackie's accumulated knowledge and experience is brought to fruition with their line of VLZ ("Very Low Noise") mixers.
Pick it up
Mackie's 802VLZ4 brings those results to you in a versatile, feature-rich 8-channel mixer that's "built like a tank" with a rugged solid steel chassis. The mixer features three of Mackie's flagship Onyx microphone preamps, which offer the superior performance of a boutique mic preamp with the toughness needed to handle the pitfalls of life on the road. Each XLR input accepts balanced mic or line level signals and features phantom power for your condenser mics. You'll be impressed by the exceptional headroom and low noise of this well-designed mixer.
Line inputs 1 and 2, as well as the stereo paired Channels 3-4, also utilize the Onyx preamps, and can be used to adjust the gain of lower-gain instruments. You can use the line/mic switches on Channels 1 and 2 to adjust the input level so you can plug instruments into these channels without a direct box. Channels 1-3 feature a 100 Hz low-cut filter on the microphone input channels to clean out rumble and low-frequency noise.
Channels 5 through 8 consist of paired stereo line inputs which accept stereo or mono signals (balanced or unbalanced) – these versatile inputs can handle the output from almost any instrument, effect, or playback unit.
The 802VLZ4 also features:
- two stereo send/returns for effects;
- two Aux sends for routing or monitors;
- a pair of RCA jacks for recording (output mode) or patching in an audio source (input mode).
You'll find 1/4" and XLR outputs for sending signals to amplifiers, powered speakers, or recording devices. You can switch the Main XLR outputs to mic level so they'll plug into another mixer. The 802VLZ4 also features dual-purpose mute/alt 3-4 switches on the channel strips that allow muting or routing the channels that you've selected to a separate stereo mix. Each channel strip features buttons for Mute/Alt 3-4 and pre-fader solo listening, as well as knobs for level, pan, and 3-band EQ.
The output stage features the ability to submix the main mix, Alt 3-4 output, and the signal from the Tape inputs, then send the mixed signal to the main outputs. The Control Room/Submix knob acts as a separate volume control for the Control Room and headphone outputs. You can use the the Pre or Post switch to configure the Aux 1 knob as a monitor send or effects send.
The Mackie 802VLZ4's combination of sophisticated features and rugged construction in a small package makes it suitable for a wide variety of situations, ensuring that you'll be ready to control whatever the music sends your way.
- channels 1-2:
- mono mic/line inputs (XLR and 1/4" TRS)
- Onyx low-noise, high-gain mic preamps
- switchable low-cut filter (100 Hz, 18 dB/octave)
- instrument switch allows guitar input without a DI box
- insertion (I/O) jack
- channel 3/4
- mono mic and stereo line inputs
- switchable low-cut filter (100 Hz, 18 dB/octave)
- channels 5/6 and 7/8
- stereo-pair line inputs (1/4" TRS)
- 3-band EQ on all channels
- high: 12,000 Hz (shelving)
- mid: 2,500 Hz (peaking)
- low: 80 Hz (shelving)
- mute and pan controls on each channel
- switchable phantom power (+48 volts) on all mic inputs
- auxiliary bus switchable pre- or post-fader
- Alt 3/4 outputs the sum of all muted channels for a separate stereo mix
- Solo bus with indicator light for metering and monitoring individual channels
- LED output meter with peak indicator
- tape in/out
- headphone and control room outputs
- steel chassis
- dimensions: 8-15/16"W x 1-13/16"H x 10-3/4"D
- weight: 4.5 lb (5.5 lb with power supply)
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # 2040767-00
What's in the box:
- 8-Channel analog mixer
- AC power cord
- Owner's Manual
Scratch & Dent items may be missing non-essential accessories. In some cases the manufacturer's accessories have been replaced with generic equivalents.
See the difference between "Open Box" and "Scratch & Dent" Outlet items
Mackie 802VLZ4 reviews
Thanks for submitting your review
More details on the Mackie 802VLZ4
Features & specs
|Line inputs||8 x 1/4"|
|Channel EQ||3-band (80, 2.5k, 12k)|
|Monitors||2 x 1/4" (CR)|
8-Channel Mixer: The Mackie 802VLZ4 is an 8-channel analog mixer.
- Mic Inputs (Ch. 1-3): The 802VLZ4 features 3 of Mackie's flagship Onyx mic preamps. The mixer's channel 1-3 mic inputs consist of female XLR connectors. You can plug in almost any kind of mic that has a standard XLR mal mic connector. Professional ribbon, dynamic, and condenser mic will sound excellent through these inputs. The 802VLZ74's mic inputs will handle any kind of mic level without overloading. Most modern professional condenser mic are equipped for phantom power, which lets the mixer send low-current DC voltage to the mic's electronics through the same wires that carry audio. Phantom power for all mic channels (1-3) is turned on and off together.
- Line Ins (Ch. 1-2): The mixer's channel 1-2 line inputs consist of female 1/4" phone connectors. These input share circuitry (but not phantom power) with the 1-2 mic preamps, and can be driven by balanced or unbalance sources at almost any level. You can use these input for virtually any audio signal. To connect balance lines to these inputs, us a 1/4" TRS phone plug. to connect unbalanced lines to these inputs, use a 1/4" TS phone plus. These two line inputs are a good place to connect older instruments that need more gain.
- Stereo Line Ins (Ch. 3-8): These fully-balanced 1/4" inputs are designed for stereo or mono, balanced or unbalanced signal. They can be used with just about any professional or semi-pro instrument, effect, or CD player.
Note: These Channel 1-2 Inserts (1/4" phone jacks) are where you connect serial effects such as compressors, equalizers, de-essers, or filters.
Tape Input/Tape Output: The 802VLZ4 offers both Tape inputs and Tape outputs.
- Tape In: These dual, unbalanced RCA inputs accept line-level stereo signals. The signals entering these inputs are always routed to the phones output, but can also be routed the main output. Use these jacks for convenient playback of your mixes. You'll be able to review a mix and then try another pass without repatching or disturbing the mixer levels. You can also use these jacks with an iPod, computer, or CD player. There is Tape Level knob which lets you adjust the level of the tape input playing in the main mix and headphones.
- Tape Out: These unbalanced RCA connections tap main mix output to make simultaneous recording and PA work more convenient. Connect these to your recorder's inputs. This output is an unbalanced copy of the main mix and it is affected by the main mix level.
Main & Headphone Outputs: The 802VLZ4 offers output jacks to connect your power amplifier, powered speakers, and headphones.
- Main Outs: The mixer's main outputs consist of two balanced XLR connectors and two unbalanced 1/4" phone connectors. These outputs feed the main mix out to line-level inputs of your power amplifier, powered speakers, or another mixer. There is Main Mix level knob which control the level of signals sent to the main outputs. All channels that are not turned fully down will wind up in the main mix.
- Headphone Jack: This stereo 1/4" jack will drive any standard headphone to very loud levels. In the headphones, you will hear the main mix as well as any source playing the tape inputs. Adjusting the main mix level will not affect the headphone output; adjusting the tape level will affect the level of the tape input signal heard in the headphones. There is a Phones Level knob which allows you to adjust the level of the signal going to your headphones.
Other Inputs/Outputs: The 802VLZ4 provides a variety of useful inputs and outputs.
- Aux Send: This is a TRS 1/4" balanced/unbalanced output, commonly used to feed stage monitors or an external effects processor. The Aux Send knobs tap a portion of each channel's signal to provide an output here, allowing you to set up a nice stage monitor mix, or to setup an external effect from different channels.
- Stereo (ST) Return: The Stereo Return is where you connect the outputs of your parallel effect device. The ST Return can also be used as an extra pair of stereo line inputs. These 1/4" balanced inputs are similar to the mixer's stereo line inputs (only without EQ, aux sens, pan, mute, or solo functions). The circuits will handle stereo or mono, balanced or unbalanced signals. They can be used fiwth just about any pro or semi-pro device. The signals coming into these inputs can be adjusted using the Stereo Return knob before passing the signal onto the main mix bus.
- ALT Out: The 1/4" outputs are the sum of any channels that have have the mute/alt switch pressed. These output are 1/4" and may be connected to balanced or unbalanced lines. For example, you can use these outputs to feed a recorder and just record individual channels by pressing their mute/alt switch one at a time.
- Control Room (CR) Out: These TRS 1/4" balanced/unbalanced outputs allow you to listen to something other than the main mix. These outputs are often used to run a nice pair of powered studio monitors in a control room.
3-Band EQ: The 802VLZ4 has 3-band equalization at carefully selected points; low shelving at 80Hz, mid shelving at 2.5kHz, and high shelving at 12kHz. "Shelving" means that the circuitry boosts or cuts all frequencies past the specified frequency.
- High EQ: This control gives you up to 15dB boost or cut above 12kHz and it is also flat at the center.
- Mid EQ: This control gives you up to 15dB boost or cut below 2.5kHz; the circuit is flat at the center position.
- Low EQ: This control gives you up to 15dB boost or cut below 80Hz; the circuit is flat at the center position.
Helpful Controls: The 802VLZ4 is equipped with a variety of useful control dials, buttons, and switches.
- Low Cut (for Ch. 1-3): This function cuts bass frequencies below 100Hz at a rate of 18dB per octave for channels 1, 2, and 3.
- Instrument Switch: The instrument switch is used if you want to connect a guitar or other instrument-level source directly to the line inputs of channels 1 & 2.
- Pre Fader Solo: The Pre Fader Solo switch allows you to hear signals through your headphones or control room without having to route them to the main mix or alt 3-4 mix.
Applications: The Mackie 802VLZ4 is great for live sound mixing, houses of worship, clubs, gymnasiums, banquet halls, conference rooms boardrooms, studio and field recording, multimedia applications, broadcast, and many other applications.