About the Wet Sounds RECON 8 S-RGB
Thunderous sound and cool light
Thunderous sound and cool light
Wet Sounds designed their RECON Series speakers to bring high-quality sound to a low-power applications, so you can get great performance even when they're connected to a marine receiver. If you don't have room for an amplifier and still want to experience rich, powerful sound, these rugged speakers are a great choice for your boat or outdoor vehicle. You'll also enjoy the built-in RGB LED lighting.
Rugged speakers with plenty of power
Each pod enclosure houses a 8" composite cone woofer and a 1" aluminum dome tweeter, designed to handle up to 70 watts RMS. The Santoprene rubber surround keeps things tight and the Nylas nylon/fiberglass frame will stand up to life in the outdoors.
Available in Silver or White.
- 8" marine speakers with RGB LED lighting (pair)
- composite woofer with Santoprene rubber surround
- 1" aluminum dome tweeter
- handles up to 70 watts RMS (140 watts peak power)
- frequency response: 45-20,000 Hz
- sensitivity: 88 dB
- impedance: 4 ohms
- cut-out diameter: 7.072"
- frame diameter: 8.88"
- mounting depth: 3.55"
- warranty: 2 years
- Our 60-day money-back guarantee
- MFR # RECON 8 S-RGB
What's in the box:
- Two 2-way marine speakers
- 2 Grilles (attached)
- 2 Rubber gaskets
- Two 8" Waterproof 2-pin female SuperSeal speaker harnesses
- Two 8" Waterproof 4-pin female SuperSeal LED (RGB) harnesses
- Twelve 1-1/4" Stainless steel Phillips head screws
- 2 Templates
Thanks for submitting your review
More details on the Wet Sounds RECON 8 S-RGB
Features & specs
|Tweeter Design||1" Dome|
|Parts Warranty||2 Years|
|Labor Warranty||2 Years|
88 dB at 1 watt |
|Frequency Response||45 - 20k Hz|
|Max RMS Power Handling||70|
|Peak Power Handling (Watts)||140|
|Top-mount Depth (Inches)||3 9/16|
|Bottom-mount Depth (Inches)||N/A|
|Cutout Diameter or Length (inches)||7 1/8|
Nylas Basket and Grille: Both the speaker frame and grille are made of Nylas, a composite mix of Nylon and Fiberglass, providing strength and stability. The grilles are held in place by three screws, accessible under the mounting gasket, but the tweeter is mounted to the grille, so it should not be removed.
Rubber Spider: Durability is further improved by the rubber spider Wet Sounds developed for their marine speakers.
Tweeters: The tweeters are mounted to the grilles, rather than to a pole piece, thus there is no chance of water leaking through the woofer cone.
LEDs: There are red, green, and blue LEDs in the back of the tweeter casing to create a glow on the woofer cone. The LEDs can be powered individually, or in any combination you like. A 12 volt power supply is needed to turn the LEDs on and a 2-amp fuse should be added in-line (fuse not included). Depending on what combination of LED wires is connected, they light red, green, blue, yellow, purple, aquamarine, or white. The LEDs can also be controlled using Wet Sounds' wireless RGB Music Controller remote (item number 867RFRGBMC, sold separately). A male 4-pin waterproof SuperSeal plug is on the wire connected to the LED housing, which connects to the included female SuperSeal harnesses. (The black wire is +12 volts, the red, green and blue wires are ground.)
Speaker Terminals: Similar to the LED wiring, a male 2-pin waterproof SuperSeal plug is on the signal input wire, which connects to the included female SuperSeal harnesses. The red wire is positive and the black wire is negative.