Molded 6U-sized rack case
Our take on the Gator G-Pro-6U-19 by Crutchfield's Jeff Miller
Both lids open for easy access to your rack-mounted gear (6U-sized case pictured).
Probably the most noticeable feature of Gator's Pro-Series rack case is the tough looking outer shell. You can rest assured that your rack mounted gear will be protected by its molded hard plastic exterior. It was designed to withstand loading and unloading, or bumping and scraping against other gear. Gator also uses heavy-duty recessed Penn Elcom® twist latches to make sure your gear is secured inside, even while moving around in the back of a vehicle.
"When the guys from Gator came to Crutchfield to show us their products, the trainer handed me a hammer and invited me to wail away...I beat on the latches, handles, and hinges, too, and couldn't break them."
— JR, drummer and Crutchfield Advisor
...And easy setup
Just as important, however, is the convenience. To use the gear itself, there is rarely a need to remove it from the case. When you get where you're going, you can open the front and back for easy access to both the control side and input side of your rack-mountable gear. Gator has designed their rack cases to stack with each other, so you can easily expand your system with additional gear.
PLEASE NOTE: Rack cases are measured in rack units (U), the standard size for a single rack space (1U=19"W x 1-3/4"H). This is a "6U" case, meaning it gives you room for six rack spaces, stacked vertically.
- portable hard case for rack mountable A/V equipment
- space for six standard size rack units (6U)
- front and rear lids open for access to both sides of your gear, also maximizing airflow
- made of rotationally molded polyethylene to keep gear protected
- molded, built-in handles
- recessed steel twist latches
- outer case designed to stack with other Gator cases
- interior dimensions: 17"W x 10-1/2"H x 19"D
- exterior dimensions: 21-1/2"W x 13-1/2"H x 21-1/4"D
- weight: 15 lbs.
- warranty: lifetime limited
- Our 60-day money-back guarantee
What's in the Box:
- Black molded audio 6U rack
- Front cover
- Rear cover
- 24 Rack screws (10-32 x 1/2")
- 24 Nylon washers
- Share It card
- Warranty Information card
- Rear rack rail offer card
Why Shop With Us?10 Reasons.
Overview: The Gator G-PRO-6U-19 is a Pro-Series Molded Military-grade polyethylene rack case. It is designed for protecting and transporting rack-mounted equipment. It features full-sized removable front and rear lids to give you access to either end. The lids feature recessed steel twist latches that can accommodate a small lock for added security. Ergonomic carry handles are molded into each side for carrying the case. The G-PRO-6U-19 is made in the USA of virtually indestructible roto-molded polyethylene and other recycled materials.
Stackable: The G-PRO-6U-19 has four 1-1/2" diameter rubber feet for setting the case upright. Another set of four 1" diameter rubber feet let you lay the case flat while using the stored equipment. You can stack another G-PRO-6U-19 (or 2U or 4U) on top, with the four rubber feet fitting into molded receptacles on the bottom unit.
Rack Hardware: The G-PRO-6U-19 provides 6U of rack space with 19" of depth. Twenty-four 10-32 x 1/2" rack screws are included, along with 24 nylon washers.
Dimensions: The G-PRO-6U-19 has the following dimensions:
Our Product Research Team
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.
Why did you buy this?
Size and ease of transportation and operating from within. The sleek look and design also was a factor in my decision. I'm excited to receive it and put it to use. [ Curtis Aug 08, 2017 ]