2007-2013 Chevrolet Silverado and GMC Sierra regular cab pickup
2007 • 2008 • 2009 • 2010 • 2011 • 2012 • 2013
In a Nutshell
In this article, we'll tell you how to replace the stereo and speakers in your pickup. Replacing the old radio isn't hard, but the dash substructure can get in the way in some cases. To avoid that problem, look for a double-DIN receiver with wire harnesses or RCA connectors located on the bottom half of the back of the unit. A variety of receivers with a depth of less than 6-1/2" will fit, but "fold-down face" receivers won't work in this truck.
Replacing the door and rear pillar speakers is pretty uncomplicated, and you have a nice variety of speaker options to choose from. There's not a lot of space for a big, boxed-up subwoofer, but a powered sub will bring plenty of bass to your pickup's cabin.
Ready to shop? Use our vehicle selector to find the gear that will fit your pickup. If you're looking for step-by-step instructions on how to install a car stereo or speakers, there's nothing better than our exclusive Crutchfield MasterSheet™. This detailed, well-illustrated document is free with your Crutchfield order, or you can purchase one separately for $9.99.
Overview of the Silverado and Sierra
The best part of driving a regular cab pickup is that when you and three friends need to go someplace, you probably won't be the one driving. The worst part is that when one of those friends has to move something somewhere, you'll definitely be getting a phone call. Then again, that might eventually lead to free pizza, so maybe it's not that bad when you think about it....
The Chevy Silverado and GMC Sierra regular cab trucks were typically more utilitarian than luxurious, but they were available with some decent (for the time) stock stereos. That said, at this point in your truck's life, the stock stuff is probably getting a bit tired. If your truck has a lot of life left in it, replacing the old gear is probably a good idea. Your friends will appreciate your new sound system while your'e heading across town with their new furniture.
The dashes differ, but radio replacement is still pretty simple in these trucks (Crutchfield Research Photo)
Factory stereo system
Regular Cab (and Extended Cab) Silverados and Sierras were available with two different dash configurations. The lower trim level trucks have a "Type A" dash, while the mid- to upper-level trucks have a "Type B" dash.
Both configurations use the same mounting kit, which, along with an antenna adapter, is included at a deep discount with most Crutchfield stereo purchases. You'll also get our exclusive Crutchfield MasterSheet, which contains the illustrated, step-by-step instructions you'll need to install new audio gear in your truck, regardless of which dash configuration you're dealing with.
It's a big space, but not every double-DIN (4" tall) receiver will fit here (Crutchfield Research Photo)
Replacing your factory radio
A variety of single-DIN (2" tall) and double-DIN (4" tall) receivers will fit in these pickups, but there are some irregularities in the dash substructure that prevent certain double-DIN radios from fitting properly. It’s best to pick a double-DIN radio with wire harnesses or RCA connectors located on the bottom half of the back of the radio, but you can also go with a number of CD receivers or digital media receivers with a depth of less than 6-1/2". A receiver with a fold-down face will not work in this truck, though, so avoid those.
To get started, enter your truck's information on our Outfit My Car page, find the receiver you want, and add it to your cart. We'll show you which mounting kit you need, and you'll receive a big discount when you purchase everything together at Crutchfield. If you have any questions, especially when you're looking for the right double-DIN receiver, one of our Crutchfield Advisors will be happy to help you make the right choice.
You’ll also need to purchase an adapter that allows you to install a new stereo and still retain your warning chimes (along with OnStar functionality if you have it), plus a relay to keep your audible turn signals working with your new car stereo. These adapters are not free, but we'll give you a very nice discount on the ones you'll need for this installation.
Crutchfield strongly recommends that you use one of the recommended adapters. Failure to do so may result in serious injury or death. It will most certainly result in our (very) polite refusal to provide technical assistance when you call us for installation advice.
Tools needed: Panel tool, 7mm socket and ratchet
Steering wheel audio controls
It's relatively easy to retain the steering wheel audio controls when you install a new stereo in your pickup. When you enter your vehicle information, our database will choose the adapter you need to make your factory steering wheel controls work with your new receiver.
Replacing your factory speakers
We'll give you a nice discount on the installation gear you'll need for the doors (Crutchfield Research Photo)
You'll need to remove the door panel to access these speakers, of course. Depending on whether your truck has manual or power windows, there will be some differences in exactly how you do that. All will be explained in your MasterSheet.
The standard factory door speakers are closest in size to an aftermarket 6-3/4" model, but you’ll need an adapter plate to install any aftermarket speaker. You can install 6-3/4" or 6-1/2" speakers and the adapter plates make installation relatively easy. The factory speakers are 4-ohm models, so you have a wide selection to choose from.
You'll need speaker harnesses to attach the new speakers to the plugs that connect to the GM factory speakers. Crutchfield includes these harnesses, plus the mounting brackets you'll need, at a deep discount with every speaker order.
Tools needed: Panel tool, 7mm & 10mm drivers, flat blade screwdriver, needle-nose pliers
Replacing the pillar speakers takes a little work, but it's nothing you can't handle (Crutchfield Research Photo)
Rear pillar speakers
These Regular Cab trucks have 4"x6" speakers mounted behind the rear side pillars. They can be replaced by same-size or 4" aftermarket speakers, though you'll need to re-drill the mounting screw holes no matter which size you choose. The drilling isn't any harder here than it is in your home workshop, but be smart, work carefully, and be sure to wear eye protection.
If you want to get maximum sound quality out of your new rear pillar speakers, purchase a set of foam baffles. These baffles fit snugly around the rear of the speaker to reduce rattling and improve performance. They also protect the speakers from dust and moisture, which is always a good thing in a truck. Baffles are an inexpensive addition that really makes a difference, here and in the doors.
Tools needed: Panel tool, small flat blade screwdriver, 7mm socket, ratchet and extension, Torx T-50 driver, drill with 1/8" bit
There's not a ton of space for bass back here, but a powered sub might fit (Crutchfield Research Photo)
Bass in your Silverado or Sierra
There's not a lot of room for aftermarket bass in these trucks, but all is not lost. There are some small powered subwoofers that could fit back there. And if you want to power your other speakers with an aftermarket amplifier, there's space back here to mount that, too.
Other upgrade options for your Silverado or Sierra
Here are some other upgrade ideas for your GM pickup:
Kick panel pods
If you really want to improve the sound in your Silverado or Sierra, install a set of Q-Forms Kick Panel Pods. These unloaded, custom-fit speaker enclosures fit into the space where your kick panels are now. They hold a set of component speakers in an ideal position, angling them to maximize sound quality. They're available in a variety of colors to match your truck's interior. Installation takes some work, but it's not beyond the realm of an experienced DIY-er.
If you don't want to invest in a big double-DIN receiver, you can still get the nav you need and more with a Garmin portable navigation unit. A portable GPS can be transferred from vehicle to vehicle, or just tucked into a storage compartment when not in use.
Installing a security system in your truck isn't easy (security systems rarely are), but it's definitely a good idea. Our Crutchfield Advisors can help figure out what you need to get the job done, but we usually recommend taking your car and new gear to a professional installer.
Find the audio gear that fits your car or truck
Visit our Outfit My Car page and enter your vehicle information to see stereos, speakers, subs, and other audio accessories that will work in your vehicle.