Skip Navigation

RetroSound R-410N

Single 4"x10" 2-way car speaker with dual voice coils

29 Reviews | 3 questions - 4 answers

Find what fits your vehicle


Can't find your exact vehicle?

Item # 068R410N

In Stock

Add to Cart

Ask an expert

Our VA-based experts can help.


Chat Email


Our take on the RetroSound R-410N

RetroSound makes it easy to replace the factory speakers in almost any classic, vintage, or even new car. Their RetroMod Series speakers feature extremely shallow chrome baskets designed to fit into a wide variety of standard speaker locations. They may look old school, but RetroSound builds their speakers from the ground up, using the latest techniques and materials.

Retrosound R-410N

One speaker, powerful sound

RetroSound makes it easy to replace the factory speakers in almost any classic, vintage, or even new car. Their RetroMod Series speakers feature extremely shallow chrome baskets designed to fit into a wide variety of standard speaker locations. They may look old school, but RetroSound builds their speakers from the ground up, using the latest techniques and materials.

The single R-410N 4"x10" speaker is designed for a classic car with only one speaker opening on its dash or rear deck. The woofer features dual voice coils, each one connected to its own tweeter. Your stereo receiver connects to both voice coils, so you get a stereo mix from a single speaker. In effect, you get two 2-way speakers in one frame, for modern sound in your vintage application.

The R-410N speaker features a powerful neodymium magnet and a low-carbon steel chrome frame that form a strong foundation. The sturdy pulp composite woofer with its Santoprene surround delivers powerful performance while standing up to heat and humidity. The two Mylar dome tweeters broadcast detailed highs without sounding shrill, and their low profile helps increase installation options.

Although efficient enough to play well with any receiver alone, this RetroMod speaker can handle the high power from aftermarket amplifiers. Replace that wornout old 4"x10" with this updated RetroSound, and your tunes will sound new again, just like your classic ride.

Important Note: This is a single 4"x10" speaker, so you'll need to purchase a pair for vehicles with two 4"x10" openings.

Priced per single speaker

Product Highlights:

  • single 4"x10"" 2-way speaker
  • pulp composite woofer cone with Santoprene surround
  • dual voice coils for 2-channel operation
  • dual Mylar dome tweeters
  • power range: 2-90 watts RMS (160 watts peak power)
  • frequency response: 43-21,000 Hz
  • sensitivity: 87 dB
  • top-mount depth: 1-3/4"
  • grille not included
  • warranty: 1 year
  • Our 60-day money-back guarantee

Fit nicely in 64 chevy II using origional mounting bracket. Sounds ok for mid and high but lacking bass. I have a underseat powered woofer that completes the system and together they sound really good. I like being able to keep origional location.

Craig, Vancouver, WA

What's in the Box:

  • One 2-way 4x10 stereo input DVC speaker
  • 12' Length of speaker wire
  • Eight 1-1/8" Self tapping screws
  • 8 Speed clips
  • Owner's manual

RetroSound R-410N Reviews

Average Customer Review(s):

(29 Reviews)

RetroSound R-410N

Don from Elmira, NY on 7/20/2017

Crutchfield Customer Review (What's this?)

I bought this for my 1954 chevy belair. It mounted right where the original front speaker was. Outstanding sound . This speaker fits right in with my Retrofit radio and rear speakers easy install and great sound. I prefer this set up because I didn't have to install speakers in the front kick panels or door panels and you get the same great sound. I am very pleased with this set up.

Pros: very easy to hook up where the original front speaker was.

Cons: NONE

RetroSound R-410N

Craig from Vancouver, WA on 7/18/2017

1964 Chevrolet Nova
Crutchfield Customer Review (What's this?)

Fit nicely in 64 chevy II using origional mounting bracket. Sounds ok for mid and high but lacking bass. I have a underseat powered woofer that completes the system and together they sound really good. I like being able to keep origional location.

Pros: Good for specific fit and not bad sound


RetroSound R-410N

Anonymous from Williamson, WV on 3/5/2017

1967 Pontiac GTO
Crutchfield Customer Review (What's this?)

I put it in a 67 gto. I did have to trim back some of the metal in the bottom to use the factory mounting brackets to put in factory dash location. For what it is it's not a bad speaker. Sound isn't the greatest but with some 6x9s in the package tray and a small powered sub it makes for a well rounded stereo for these old cars. I'd order again.



Suprising sound in single speaker space.

Scott from Parkton, MD on 12/27/2016

1969 Chevrolet Camaro
Crutchfield Customer Review (What's this?)

For vintage car applications this speaker has really suprised me with the sound you get from it. Of course a modern component style speaker is better, but when cramped space, single center speaker dash confines rule that it, this is a great speaker, from experience better than 2 really small speakers in that space. I have used it with converted original radios, and this Pioneer amp and you get all the sound you need. Loud enough and clear enough to enjoy your music blowing down the road with the windows down.

Pros: Easily fits single speaker dash, dual wiring connections, plenty of sound.


RetroSound R-410N

Michael from North Andover, MA on 10/29/2016

1980 GMC C Series
Crutchfield Customer Review (What's this?)

Installed it in my 1980 GMC truck. Just what I needed for upfront highs and decent midrange using the 50w per channel amp built into my receiver. Very happy with with it.

Pros: slipped right into the stock opening. Two of the flanges matched right up to the factory screw holes.

Cons: cant think of any

RetroSound R-410N

Anonymous from Russellville, AR on 8/29/2016

1979 Chevrolet C Series
Crutchfield Customer Review (What's this?)

gave extra for this speaker so I could have a nice sound(not great just nice) on 2nd day it was already rattling. hard to believe but I'm jus not real pleased with this speaker. also was a real pain to replace.

Pros: fit really nice

Cons: started rattling almost from the beginning

Crutchfield response on 8/30/2016 Once we saw this review, our Tech Support team reached out to help the customer. We'll either help him get these speakers working properly, or help him return them for an exchange or refund.

This is a winner!

Jim D from Port Saint Lucie, FL on 8/25/2016

1972 Ford Galaxy 500
Crutchfield Customer Review (What's this?)

I found the speaker to meet my requirements in full. In fact, my car model is a LTD convertible. The speaker required about 15 minutes alteration to fit in the dash pad. Great fit other than that. Sound is great, better than door speakers. Definitely not top shelf but way more than I expected. Highly recommend for this application.

Pros: Very good sound and reasonably easy installation at a great price.

Cons: None as of yet.

Great Sound

DJ from Pottsville, PA on 7/28/2016

1978 Chevrolet C Series
Crutchfield Customer Review (What's this?)

Sounds great as a drop in replacement in my 78 c10, hard rubber around speaker caused a clearance issue but wasn't hard to fix

Pros: Sounds great as a drop in replacement in my 78 c10

Cons: hard rubber around speaker caused a clearance issue but wasn't hard to fix

Groovy, Man

ArrDub from Western VA on 4/28/2016

1984 Chevrolet C Series
Crutchfield Customer Review (What's this?)

This speaker, when I finally figured it out, sounds great. It will stick up from the dash a bit more than the original, but I can trim foam with the best of them. The instructions could have been more clear, but those are the instructions in the box, which are in no way a fault of Crutchfield.

Pros: Sound great. I got some killer 3½' speakers to sit on the outside corners of the dash, and when I get it tuned up to my hearing aid, it's about as groovy as a 3 hour Blue Cheer concert in Bimini.

Cons: Instructions could be improved.

Great retro-fit for mono cars

JasonC from Minnesota on 1/9/2016

1968 Oldsmobile Cutlass
Crutchfield Customer Review (What's this?)

I never thought I'd ever get stereo sound in the front of my late 60s Olds without some major work. Found this baby and it works great! Plenty of power, and sounds great. Probably doesn't sound as good as if you did a full overhaul, but considering all the wind, engine, and road noise the car already has, it's going to do just fine!

Pros: Great solution for your old mono dash speaker.

Cons: Couldn't use the stock mounting bracket and needed a RS-UB1KT to make it fit.

retro sound speaker

Bob from Maryland on 1/3/2016

1967 Chevrolet Camaro
Crutchfield Customer Review (What's this?)

Good sound from a speak with a dual voice coil. I was able to mount the speak in my 1967 Camaro where the factory mounted the original.

Pros: Good sound and did not have to destroy the looks of my car

Cons: Product was shipped by Fedx and it took 10 day to receive but what else from Fedx.

RetroSound R-410N

GTB from Sierra Vista, Arizona on 12/6/2015

Crutchfield Customer Review (What's this?)

The tech said the oem size was 4X10 because I had not removed the radio or speaker before ordering I went with his info. When I recived the new radio and speaker I removed the oem and found that I should have a 6X10. I was able to install the 4X10 and make it work. I just didn't feel like going thru the hassel of sending it back, my choice.

Pros: It did fit, even if it was the wrong size.

Cons: The tech should have better info on vehical fits.

Great Concept, Poor and Cheap Execution

Anonymous from WI on 10/23/2014

1966 Chevrolet Chevelle
Crutchfield Customer Review (What's this?)

Upon opening the box, only one thought crossed my mind, "I paid close to $80 for this?!" Speaker is very lightweight. The chrome backing as seen in the pictures you'd assume was metal? Nope, chrome plated plastic. Now, I did not tear apart the dash of my 66 Chevelle to test fit, just wired the speaker up and placed on top of the dash. Sound is decent at low levels and I was actually impressed. However, after starting the car, the sound from the speaker was no match for only sound worth hearing in a classic car, the rumble of the V8. Decided what's the point of a sound system in a classic car, and ended up returning the speaker and installing a radio blank-off plate. But then again, your mileage may vary.

Pros: stereo sound from a single speaker. Decent sound quality with car off at low volumes.

Cons: Chrome plated plastic. Cheap feel. Very light.

Great speaker for adding stereo where it didn't exist.

Roy w. from Tucson Arizona on 2/4/2014

1980 Chevrolet Malibu
Crutchfield Customer Review (What's this?)

This speaker was the perfect solution for adding front channel sound to my 1980 Malibu which only had one front speaker.

Pros: Exact fit good sound

Cons: No cons

perfect for my 68 camaro

JeffF from huntington wv on 12/15/2013

Crutchfield Customer Review (What's this?)

great front fill in sound with 6x9's in the rear deck and small sub in the trunk

Pros: great speaker

Cons: mounting was a challenge but not anything due to product

Dashboard speaker

Retro sound 4 x 10 from Conroe, TX on 7/11/2013

1986 GMC C Series
Crutchfield Customer Review (What's this?)

This speaker fit perfectly and it sounds amazing

Pros: Doesn't leave a bump underneath the dashboard panel

Cons: None really but it just doesn't have as much bass as I would like it too

Gets the job done.

Walter from Cleveland, OH on 6/17/2013

Crutchfield Customer Review (What's this?)

Replaced front single center of dash speaker in 1967 Camaro. This speaker has dual voice coils so both left and right channels can come through one speaker. Install was smooth enough and speaker looked to be of reasonable construction. Sound is middle of the road and not as good as a modern factory speaker let alone what you would like to see from an aftermarket speaker. Considering you are getting two speakers in one it may be fair to only expect OK sound quality from this speaker. It is not a "high end" price either. Also it is a HUGE improvement over the original speakers. The car is a convertible and GM put one speaker in the front dash and one in the back. The back speaker was buried under the top when it is down and could not be heard. Lastly the support bracket supplied was way to flimsy. I had to use some thicker steel I had laying around or the radio would have fallen away from the dash and rattled.

Pros: Left and Right channels from one speaker

Cons: Only medium sound quality. Weak mounting bracket.

Too Big for 1965 Mustang

Bill L from Wallingford, CT on 5/24/2013

1964 Ford Mustang
Crutchfield Customer Review (What's this?)

Product seems nice but it is too big to fit in the stock opening of my 64 1/2 Mustang Coupe

Pros: Seems Nice

Cons: Does Not Fit in Stock 64 1/2 Mustang as advertised

Easy Install

Sibon3 from Chicago, IL on 6/6/2012

Crutchfield Customer Review (What's this?)

Nice construction. Easy install into 1969 Cutlass Dash using the supplied mounting kit. Perfect solution for getting dual channels through the single speaker location in the dash.

Pros: Easy install ans=d comes with install hardware kit

Cons: Wish it came with an integrated mesh cover to protect speaker. Installed my own.

retrosound 4x10

nate from rosemount mn on 4/4/2012

Crutchfield Customer Review (What's this?)

overall i am pleased with this speaker although it wasnt a total bolt in installation. I purchased the speaker to replace my original in my 69 superbee. I liked the dual voice coil idea due to the fact the car only has one front speaker. I did need to use the exising frame off of my old speaker to make this one work with the ca because the speaker mounting holes provided were a inch too short.. I am powering it with a pioneer 4400, no amp and a pair of 6x9 rockfords in the rear. Sound quality is good

Pros: good fit, dual voice coil

Cons: cost is kind of high for what you get.

Great Vintage replacement

Zipper from Rochester, NY on 3/5/2012

Crutchfield Customer Review (What's this?)

I purchased this to fit the 1965 Rambler American 440 convertible I am working on. The inclusion of the mounting kit was just what I needed to complete the installation. I went a bit farther than most. I have a hidden stereo amplifier in the glove box for my i-tunes but I mounted and wired a 4 pole, double throw switch so that I can switch it to the series mode and hook it back to the original AM Radio. Plays great and sounds better than the original speaker when hooked to the radio and the clarity for the stereo is wonderful. Makes great sound and fits perfectly with the included mounting kit.

Pros: Easy fit, great for going to a stereo without cutting or modifying the car. Will also work as an 8 ohm speaker when the left and right channels are wired in series. Great versitility!

Cons: None. Sounds great.

Retrosound R410N

JerryC from Bufalo,NY on 2/19/2012

1970 Pontiac GTO
Crutchfield Customer Review (What's this?)

Finally stereo sound in front of my '70 GTO without cutting holes! Bought this speaker as an open box item without regret. Took me 10 minutes to make a mounting bracket and it was in.

Pros: Easy install, good sound

Cons: Wish I found this sooner.

Retrosound R-410N

Cooper from Falls Church, VA on 1/1/2012

1982 Dodge Ramcharger
Crutchfield Customer Review (What's this?)

A geat find! Perfect fit, sound is great, hooks up as stereo with only one speaker, takes both the front left and right wires.

Pros: It is an exact fit for my 1982 Dodge Ram D350, which should also cover the other D series as well as the Ramcharger.

Cons: A little bit too high which causes the dash's speeker cover to bow slightly. I am going to use the Dremel tool to trim some of the height of the oval ridge on the bottom side of the cover so it will fit without bowing.

Not for original 70's era radios

Big B from Louisiana on 10/19/2011

This may be a great speaker but ....This speaker will not work with an original 70's era GM radio. It requires a 10ohm impedence speaker ...this one is 4ohm. You can harm your radio if you hook up the wrong impedence speakers.



Retrosound 4x10

Pontiac Ed from Downers Grove, IL on 6/8/2011

Crutchfield Customer Review (What's this?)

I bought this speaker for a factory center dash speaker application in a full size '62 Pontiac. This speaker is very shallow and it solved an interference problem between the previous replacement dash speaker and the body of the original AM radio. Its unique design allows you to wire both channels to one speaker to give a fuller sound from a single speaker, but you can wire it to a single channel. I wired it to both front channels of a moderately priced Alpine head unit and it sounds pretty good although it would probably sound better if I ran the signal through an amp. I did run in to a slight fitment problem with the factory speaker studs in the dash. I had to file the fastener holes in the speaker frame slightly to get the speaker to fit, but that's no big deal. I would definitely recommend this speaker to people trying to get better sound in an older car while maintaining the factory appearance of the interior without modifying the car. Its short profile is a major asset for dash applications



RetroSound R-410N

DonZ from Huntington In on 11/30/2010

Crutchfield Customer Review (What's this?)

The mounting system made it a great way to install it in my 1969 Olds 442 with air conditioning. I don't know how I would have mounted any speaker without the bracket and screw. The sound is descent, a whole lot better then what ever came from the factory.



RetroSound 4x10 speaker

Tom M from West Palm Beach, FL on 10/23/2010

Crutchfield Customer Review (What's this?)

What a perfect solution to the blown out flush mount dash speaker in my 59 Coupe DeVille. Installation took less than 10 minutes. The speaker had the exact spacing for the mounting bolts/nuts and it sounds great with my XMp3 and an amplifier hidden inside the glove box. I'm glad I checked Chrutchfield for the solution. Delivery was great too. Awesome product, service, web site, delivery etc...resulting in total customer delight!



2 speakers in one

David from Mercer, PA on 3/27/2010

1978 Pontiac Firebird
Crutchfield Customer Review (What's this?)

This was a great purchase for replacing my single center mounted speaker in the front dash. I had to modify the bracket, but the speaker had some bolt holes to attach the new mount. The fact that it serves as both the left and right speaker in a single package works out great and the sound is fantastic compared to the old original speaker.



RetroSound R-410N

Doug from cincinnati on 8/16/2009

2001 Chevrolet S10
Crutchfield Customer Review (What's this?)

Great sound quality i can expect even better quality when my new stereo and door speakers come in great customer service




Hands-on research

Features and Specs

Speaker Size Vehicle-specific
Design 2-way
Tweeter Design Dual Dome
Impedance (Ohms) 4
Tweeter Composition Mylar
Woofer Composition Pulp Composite
Woofer Surround Santoprene
Parts Warranty 1 Year
Labor Warranty 1 Year
Sensitivity (1W at 1 meter) 87
Sensitivity at 2.83 volts N/A
Frequency Response 43 - 21k Hz
Minimum RMS Wattage 2
Maximum RMS Wattage 90
Peak Power Handling (Watts) 160
Top-mount Depth (Inches) 1 3/4
Bottom-mount Depth (Inches) 2 3/16
Cutout Diameter or Length (inches) 0

Product Research


Woofer: The speaker features a rigid pulp composite cone woofer with a Santoprene surround. The woofer uses a Neodymium magnet to achieve its shallow depth, so it fits in tight factory locations.

Tweeters: Two Mylar tweeters are wired separately so this single speaker will accept a stereo input.

Dual Voice Coils: The woofer has dual voice coils, each wired with one of the tweeters. The stereo input is useful in many older cars with a single speaker location in the dash or rear deck. If used in a standard two speaker 4x10 application the inputs should be wired in parallel (to present a 2Ω load) or series (to present an 8Ω load).

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Staff Reviews

Product reviews from the Crutchfield Labs

What are the Labs?
Q & A

Customer Q&A

3 questions already asked

What is the size of the existing speaker? The mounting kit includes some adjustable bars that you can bend to fit. The cutlass had a bracket that connected to the bottom of the speaker to hold it in place. That bracket wasn't used for the new speaker and instead the universal one was used with a little bending. [ JASON  Dec 01, 2016 ]
I had the same speakers in my 1965 Chevelle so I'm guessing they will match up. [ William  Dec 01, 2016 ]
You can check to see if this will fit your vehicle by using our Outfit My Car tool: For additional details on fit or installation please contact an Advisor by phone (1-800-324-9695) or online chat. They will be able to pull up your vehicle and give you the details on if this will fit and what you will need for an installation in your vehicle. [ Krissy  Jun 22, 2016 ]  Staff
I'm sorry we do not. The brackets we have are for round speakers like 6 1/2, 5 1/4 to adapt to different size cutouts. This size speaker is usually a direct replacement so adapters are not needed or modification may need to be done. Hope that helps. [ Kenny  Jan 18, 2016 ]  Staff