Awesome for a small AMPLIFIER
Pros: Powerful and small also easy to install
Cons: Size ... ? Not bad for 1800w
Our experts help you pick the ideal gear for your needs.Meet our advisors
Free tech support for the life of your gear.Read about our one-on-one expert help
You may return items that are complete and like new for any reason within 60 days.See the details of our return policy
Earn one point for every dollar you spend and use those points to save on future purchases.Get full details on Crutchfield Rewards
We offer vehicle-specific installation instructions, dash kits, wiring harnesses, and speaker accessories at deeply discounted prices with car stereo and speaker purchases. Available for most vehicles.Learn more
Our customers have trusted us with their business, and they’ve helped us win awards for our service.Check out our most recent awards
The manufacturer’s warranty always applies.See more details
Kenwood Performance Series car amplifiers offer long-term reliability and superior sound quality in a compact, no-nonsense package. The KAC-9105D mono sub punches out up to 900 watts RMS to your subwoofers. A rugged cast-aluminum heatsink combines with two cooling fans to keep this amp running at optimal temperatures, even when you're pushing your system hard. And this bass workhorse will handle a 1-ohm load without breaking a sweat, so go ahead and hook up multiple subs.
A built-in low-pass filter lets you adjust the output so you'll get the best sound possible from your subwoofer/box combo. You can dial in up to 18 dB of bass boost if you want to fatten up the sound. A switchable subsonic filter eliminates inaudible, ultra-low noise that could detract from your sub's performance.
An aluminum cover plate covers and protects the amp's controls and connections, giving your installation a professional look. Speaker-level inputs and signal sensing turn-on allow these amps to hook up to factory radios without preamp outputs.
Awesome for a small AMPLIFIER
Average Customer Review(s):
Awesome for a small AMPLIFIER
Pros: Powerful and small also easy to install
Cons: Size ... ? Not bad for 1800w
Awesome amplifier! Even as a Refurb, this thing kicks serious butt. I love the quality of the sound I get out of my subwoofers.
Pros: Love everything about it, except one tiny thing, the size!
Cons: The size of the amp was to large to fit under my seat to hide it out of view(I drive a Honda Civic, Small bucket seats). But that is ok, I have plans to upgrade my trunk and "Display" it.
This product met and to an extent, exceeded my expectations. Other than some cosmetic blemishes the product installed easy and gets the job done. Cannot beat for the money.
Pros: Small and compact Easy install Powerful Cost effective
Cons: Only 30 day warranty Few cosmetic blemishes
this amp has a real nice amount of power you will be surprised of how well it performs I hooked it to a 12" mtx 8000series sub wired at a 2ohm load in a ported box it pounds the heck out of it great power for the size and price
Pros: small chassis and price great power
Cons: wish it had a remote gain switch
Amp preformed good but didn't last to long went out about a month after purchase.
Got this amp originally to power 2 kicker cvt 10's that 400 watts piece , i ran them at 2 ohms and didnt beak a sweat , but those weren't big enough so i got 2 fosgate p3's dual 2 ohm voice coils and wired them to .5 ohm yes half an ohm and puts out great and still doesnt get hot , good amp !
I like this amp it powers my two 400 watt suns with no problem.
Pros: Produces more than enough power
Cons: I haven't had anything bad with them
This amp is a great deal. It powers my Kenwood KFC W3013's very well. I push them hard all the time and this amp never seems to get hot
Pros: Built it fan, gives outstanding power
Its so easy to install and small. I recommend this item to all future purchases
after i destroyed my last amp, i picked this one up, and have not been disappointed. nice and easy install, not too massive for my lil trunk, and it seems to soak up heat well. nice clean sound with lots of lil extras that are nice. being able to turn sub-sonic frequencies on or off is pretty awesome too. i likes to keep mine on:)
Pros: smooth sound, lil to no electrical interference, rca jacks make installs even easier
Cons: the size is the only thing i can think of, and thats only bc its sittin in a tiny trunk
Bought this in the "bass package" with Kenwood subs. It sits in the rear of my Suburban. Very deep and satisfying bass. Never misses a beat.
Pros: Deep, clear Bass
After doing some amp research, I was very disappointed when I found this amp retailed for this much. I only have two 10" Kenwood's, so I can't let this amp show its full potential yet, bet even having it turned down, the output is amazing. It can hold the low notes for longer than I can stand it! I would highly recommend this amp, and even if you cant find it for a cheaper price, it's worth the price!
Pros: Design, power ouput
Cons: Just a few dollars too expensive.
Purchased this amp as part of a subwoofer kit. Crutchfield took the guess work out matching up all the components. The combo works great!
Pros: Kenwood quality and tons of power
Outstanding product! My amp blew out last year so I had to replace it; it didn't really do the job so I tried the Kenwood amp. I have no complaints; it sounds great and delivers great power.
Pros: great power delivery and great looks
Truly was a great amp running at 1 ohm to my dual voice coil polk audio dxi's. But after a good year of abuse the amp showed its age and just died. Checked everything and the amp simply fried out. At 900 rms u heard my cavalier coming from a quarter mile away. The amp hit real hard and the bass was clean but had some distortion. but it just simply wasnt solid in the long run. I may explore my options with another brand of amplifiers. But for the money I think kenwood is a little overrated. Anyone can make powerful amps. I dont think kenwood is one of the best anymore!
Pros: Powerful. Punchy. Deep.
Cons: Unstable. Didnt break my windshield..
I bought this amp for 2 Kickers CVX sub woofers about a month ago and ever since I installed it.... I've been loving it. The power it has to push my subs is great. Thanks to crutchfield advisor Shane I have the best system on the block
it's really excellent I haven't seen anything like this before but is great
Pros: I like it it sounds really clear now
Cons: everything is really positive on a in the Rue quit on me it works pretty good I love I'm in love with it
Amp is weak it does have power but cuts out very quickly ... I purchased this amp with a 2 year warrenty and have had too send it back twice already and its getting bad again and the warrenty is not up yet .... if you got cheap weak speakers then by all means buy this amp but anything like my type Rs nope they pull way too much outta this thing !!!!! all in all Im disappointed !!!!!!!
Love the power it puts out. Plus the sleek, attractive look to it. I'm running this amp at 2ohms to two 12" Kenwood KFC-w3009's(older subs) and I can make it bump with maintaining quality sharp bass kicks in my sealed box. Before i was running these same subs to the earliest model of this amp, the KAC-9102d, but the 9105d dosen't seem to be hitting the highs or lows as well as the 9102d,(any suggestions?) but the 9105d still delivers mid frequencies with a very powerful kick that everyone is looking for in their setup! But i also think that is because the 9102d had a HPF as well as a LPF. So it let the desired note frequency in and hit. nonetheless it is a great amp worth the money!
Pros: Nice sound. Very sleek and versatile. Worth the price. Has some very nice features in the amp. Mid frequencies have a huge kick which could shake the block. Very powerful!!
Cons: No high-pass frequency.
I bought this amp for my older brothers alpine type r sub, and it works great. Now i am getting a jl audio v2 sub.
Pros: Easy to set up
Cons: the mounting screws and brackets didnt work, i had to buy new mounting stuff.
This for my friend I helped install with. The problems That others seem to be having sounds like low Voltage and/or Low Amperage That may require people to look into the Alternators! I installed 2 of these amps in my friends 86' 5.0 Mustang, and they are working great after upgrading the alt. to 120 amps. People need to remember that you can only get so much out of an alt. and the rest will have to come from somewhere or the amp will protect itself. Most amps are rated at 13.8-14.4 volts. Most alt. only put out 50 amps, but the vehicle needs most of those amps to run correctly. These amplifiers work very well if installed, and tuned correctly! Well worth the money!
Pros: 1ohm stable! Light weight!
Cons: Fan(s) could be more efficient!
Wanted to update my last post. and start by apologising for my spelling not my strong point. I bought a 50 farad cap and the head light dimming went away for sure. Amp still cuts off. although its not as fequent as before, it still happens. my cap stores between 14.4 and 13.9 volts. After playing several songs, the amp cuts off when the cap reads 12.4 or lower. Im not sure what that means my guess is the amp is sucking so much power it cant handle the load and goes into protection mode. Since i bought the cap it seems silly to only run a single amp so i ordered two more sums and an amp and im in the process of hooking up my other amp for the door speakers. 4 more hours and ill have everything together.
Pros: simple install good sound 90% of the time
Cons: cutting out during high loads
I've had this amp for just over year and a half running two fosgate p2 at 2 ohms defently gives them a work out. Noticed incredible difference when I switch to deck with 4v outputs. I have same problem as others tends to cut out after running deep bass after a few mins the hitter the day the faster. I don't agree about the terminal size as stated by someone else, I got full 0 gage wire in without much hassle. After reading reviews here going to buy a compassator soon to see if it fixes the problem. Over all good amp never cuts out on rock music but can't make it through Beamer Benz or bently. If compassator doesn't correct problem I'll be buying new amp soon!
Pros: Price power
Cons: Cuting out dimming lights
I love this amp. I hooked it to a single kicker L7, and the more volume I give it, the more power it gives me back. An excellent buy for the money.
I don't have it installes yet, doing it today. But my battle buddy has this exact amp and is running two Alpine SWR-1522D With no problem at all so I am expecting that one Alpine SWR-1223D Will bump very hard. Thank you for the very good over the phone customer service and once again thank you and God Bless America and our troops.
Had it hooked it to my 2012 Kicker L7 wired at 2ohms, running 0 to 4 gauge wiring. The bass would hit but after a min of bass hitting then bass note would get weak. Cheap price though on amp but wasn't happy with performance.
Cons: Performance Sucks.
For the price nothing beats it.
Cons: No gains control wired remote would be nice
I bought 2 of these amps. Awesome power. Only thing. I read it is suppose to have 2 fans. And on both of mine and a friends they do not have 2 fans. It is only 1 fan. But, they are in my 03 focus trunk and never over heater. Great power and reliable. Daily user. recommend this amp to everyone.
Pros: Small, powerful, fan cooled, almost everything about it.
Cons: Will not fit a 0 gauge for the power wire.
I got this amp with 2 12" kenwood subs, so far the amp is great and I love it, I used this setup to replace an old MTX sub/amp kit that I have and I am glad I finally increased the power. I haven't had any problems with the amp or subs yet and I don't anticipate that I would either. I think some people that have problems with the setup might not have it setup correctly or most likely need a capacitor that can supply those deep base notes because it works great for me. Like I said the only thing I was disappointed with they kenwood needs/should change is to make the power/ground terminals much bigger, and maybe even redesign them like some of the other high output amps I have so that they can fit 4 gauge wire much easier.. I had to trim the wire down quite a bit and even then it was hard to get in, I will be looking to get a longer gold plated screw to fix it if I can find one.
Amp was great, paired it with two kenwood subs and sounds great, being the first time installing subs, it took time to tune in, but once tuned they were flawless.
Well, there sure has been a lot of people complaining these amps are cutting out on them. Worked just fine for me!
This amplifier is so flawed. After checking with multiple installers apparently kenwood amps are notorious for cutting out problems. I personally like to play my subs loud and this amp cant handle any deep or powerful notes. i had it wired to two 12 inch kenwoods wired to 2 ohms and it would fade out whenever a deep or powerful note would hit. It got terribly annoying and i upgraded to the kicker 11zx750.1 and i couldnt be happier. Running at 930 rms (30 rms more then the kenwood claims at 2 ohms) i am getting so much more power. I got enough more that I blew one of my subs with everything turned well below half power. I could max out my kac9105d and it would play nowhere near as loud and cut out. Go kicker, forget kenwood
its like it brand new but for half the price..... worth buying factory refurbished
running this amp for the last few weeks now... provides more than enough power to 2 twelve inch subs. At first i was surprised because this amp is so light i thought it was a cheap pile... but it delivers powers and its lightweight , which means it will cool faster. Overall Kenwood is great choice again.
The amp worked fine for a month, then it started cutting out until it just stopped working. After waiting three weeks for kenwood to fix it, it worked for three months and now the same thing happened. I would never recommend anyone to buy anything kenwood after the frustration that this amp put me through.
I've read many reviews that haven't been very positive about this amp. I'll tell you what, this amp rocks. I've been pushing two JBL 10's (soon to be JL Audio w3's), and it can push out more power than my subs can handle. My subs can handle quite a bit too! My dad can hear me coming up the street! I shake the house, it's just awesome. The only bad thing, it dims my lights pretty noticeably, so if you are looking for pushing this amp to the limit or farther than I'm pushing it, then you will at least need a good capacitor. Overall, this is a very good amp for the money. Everyone loves my sound system, except for cops. hahah. Very good amp!
This amp is well worth the money. It pounds my 2 12 inch kenwoods insanely! I would defiantly recommend this to everyone. You can hear me comin with this amp. Provides the perfect amount of power to the subs. It also arrived next day in shipping.
buying refurbished is not bad at all considering the pricing... haven't had any problems with amp at all easy to install...im currently running it at 4 ohms powering 2 10" polk audio subs rms 275 amp currently powering about 235-240 to each sub...so it sound pretty darn great...this is a good powering amp if you are into accurate bass as i am...eventually i will use amp at capacity @ 2 ohms for 500 rms subs will update at that time!!!
excellent product. provides plenty of power to my subs, with plenty of room to spare. great heat management. I've run it at high volumes for several hours with it being in an enclosed location and its never gotten too hot. looks great (lights are a bit much) and set up is a breeze.
I got this amp hooked up to 2 10" alpine type-r's. Its a perfect match for them with 300 watts to spare. I hooked it up to 2 ohms and it makes these 10s flex! Stays cool thanks to 2 built in fans. Also looks slick
Great amp worth every penny, it pounds my 2 12" Kicker CVR's HARD!!
Awsome amp. pounds my 2 excelon 12's pretty good, but i need larger power and ground wires. ill give it a 5 stars when i stop popping fuses! lol
|RMS Power Output (Watts x Channels)||
500 x 1
|Peak Power Output (Watts x Channels)||1800 x 1|
|Power at 2 Ohms (Watts x Channels)||900 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||1|
|Best Frequency Response||10-200 Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||100 dB|
|Low-Pass Crossover Frequency||50-200 Hz|
|Low-Pass Slope (dB/octave)||24 dB/oct|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/C|
|Bass Boost||0-18 dB|
|Bass Boost Frequency||40 Hz|
|Speaker Level Inputs||Harness|
|Preamp Outputs||1 pair|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Class D Amplifier Design: The KAC-9105D is a Class D mono-block amplifier, which uses digital switching to amplify audio signals. This design results in high efficiency and less heat.
MOSFET Switching Power Supply: The amplifier utilizes a MOSFET switching power supply providing thermal stability and efficient switching speeds guaranteeing performance and dependability.
Mono-Power Amp Design: The Kenwood KAC-9105D is designed with specific features to power your subwoofers with a frequency range between 10-200 Hz. The amplifier can handle impedance loads down to 1-ohm.
CEA 2006 Compliant: The KAC-9105D's power ratings are measured according to the strict standards dictated by the Consumer Electronics Association (CEA). These standards allow you to accurately compare the rated power output of all CEA 2006-compliant amplifiers, even if they come from different brands. Manufacturers who adhere to the standards can display the CEA 2006 logo on their products and packaging. Amplifier Power Ratings:
Note: This amplifier is not designed to power a full-range speaker.
Cast Aluminum Heat Sink: The Kenwood KAC-9105D utilizes a cast aluminum heat sink design to ensure that the amplifier stays at its optimal temperature.
Fan Cooled: There are two fans and two vents located on the back side of the amplifier to help dissipate heat and ensure cool, reliable operation. Make sure not to block these vents or fans when you install the amplifier.
Protection circuitry: The amplifier features protection circuits that will turn the amp off in case of the following events:
Aluminum Cover Plate: The amplifier's controls and connections are hidden under a removable extruded aluminum cover plate. The cover plate provides a professional looking installing while helping to protect the amplifier's connections and control settings. The cover is held in place by two hex head screws. An allen-wrench is supplied to remove the cover.
Blue/Red Illumination: The Kenwood Mono-Channel amplifier features a blue and red LED illumination when the amplifier is turned on. When the power is turned on to the amplifier, the Power indicator will light up red. This indicator will turn off with the amplifier and will turn off if the amplifier goes into protect mode. The amplifier also features a Blue LED lamp on the top of the amplifier which illuminates when the amplifier is on.
Signal-sensing Turn-On Circuitry: When the speaker-level input is used, it is not necessary to connect the power control wire (turn-on lead). The amplifier senses the signal from the speaker-level input and turns the amplifier power on automatically. Shortly after no signal is detected, the amplifier will automatically shut itself off.
Gain: To accommodate the varying range of signal levels coming from today's factory and aftermarket radios, the Kenwood KAC-9105D features an adjustable, independent gain control (0.2-5.0V). This means that no matter what kind of radio is connected to this amplifier, the appropriate gain control adjustment can be made to ensure loud, clear, distortion-free music.
Low-Pass Filter: The KAC-9105D has a built-in 24dB/octave low-pass filter that is continuously variable from 50Hz to 200Hz.
Bass Boost: The bass boost is adjustable from 0-18dB at 40Hz.
Phase Switch: This amplifier is equipped with a 2-way phase switch. You can choose 0° (normal phase) or 180° (reverse phase), whichever position results in stronger performance for the subwoofer.
Infrasonic Filter: This amp features an 18dB/octave Infrasonic Filter. Ultra-low frequencies that cannot be reproduced by a subwoofer do not become sound but become unnecessary oscillations, which affect sound by causing distortion. These frequencies also waste amplifier power and can cause damage to speakers. Setting the Infrasonic filter switch to 15Hz or 25Hz cuts the frequencies below the respective frequency to improve the reproduction performance of the speakers by eliminating harmful distortion.
Power Connections: The power and ground connections are 0.5625" wide screw terminals that will accommodate up to 4-gauge wire. The remote turn-on terminal is 0.3125" wide and will accept up to 8-gauge wire. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are recommended for the power, ground, and remote wires.
Speaker Outputs: The Kenwood KAC-9105D is equipped with two pairs of gold-plated speaker terminals for an easy parallel subwoofer connection. All four speaker terminals are 0.3125" wide screw terminals and will accommodate up to 8-gauge wire. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are recommended for the speaker wires.
Line Level Input: The mono-channel amplifier is equipped with a single pair of gold-plated RCA line level inputs.
Speaker Level Input: The KAC-9105D comes with a two channel speaker level input harness. Once you splice the speaker wires from the receiver to the harness, you have plug-in convenience to the amplifier. This feature makes it easier to add an amplifier to a factory radio or to a receiver with no preamp outputs. The maximum power output from the source receiver can be no more than 40 watts.
Line Level Output: The amplifier has a pair of gold-plated RCA line level outputs for feeding a full-range stereo signal to another amplifier. It is the same signal that is input through the line inputs. The amplifier's crossovers have no effect on the line level output signal.
Fuses: The KAC-9105D is equipped with three 30 amp ATC blade fuses.
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.
You can find subwoofer wiring diagrams here:http://www.crutchfield.com/learn/learningcenter/car/subwoofers_wiring.html?showAll=N [ Jeff Jan 08, 2014 ] Staff
If you purchased the product from Crutchfield, feel free to contact our Tech Support team. Our toll-free Tech Support number is printed on your invoice, and is also available under the "My Orders" tab in the "My Account" section of our website. If you did not purchase the unit from Crutchfield, then you may want to contact the manufacturer. You can also post your question in our forums: http://community.crutchfield.com. Or try our online support center: http://crutchfield.custhelp.com/app/answers/list/kw/. [ Jeff Jan 07, 2014 ] Staff