Skip Navigation

Kenwood KFC-P605ie

6-1/2" component speaker system (New Stock)

5 Reviews

Find what fits your vehicle


Can't find your exact vehicle?

Item # 113KFCP605

This item is no longer available.

Shop all 6-1/2" Speakers


Our take on the Kenwood KFC-P605ie

Component speaker systems owe their natural sound and excellent imaging to the separation of the tweeter and woofer. You can have the outstanding performance of components at an affordable price with Kenwood's KFC-P605ie 6-1/2" component speaker system.

See all of our Special Edition Kenwood products

Component speaker systems owe their natural sound and excellent imaging to the separation of the tweeter and woofer. You can have the outstanding performance of components at an affordable price with Kenwood's KFC-P605ie 6-1/2" component speaker system.

You'll enjoy the silky highs contributed by the 3/4" UFLC soft dome tweeter, mounted on Kenwood's unique Image Enhancer. The Image Enhancer baffle helps eliminate reflected sound waves that distort the high frequency output. There are plenty of mounting options — you can flush-, surface-, or angle-mount the tweeters for optimal stereo imaging.

The tough whisker-pearl mica injection-molded poly woofer works with its rubber surround to provide tight, responsive bass. The crossover network (5,000 Hz) sends the proper frequencies to the tweeter, and guards against excessive input power with a built-in protection circuit.

Priced per system

Product Highlights:

  • pearl mica injection-molded polypropylene woofer
  • rubber surround
  • 3/4" UFLC soft dome tweeter
  • 5,000 Hz external crossover
  • frequency response 35-25,000 Hz
  • power range 8-50 watts RMS
  • peak power handling 200 watts
  • sensitivity 91 dB
  • woofer top mount depth 2-1/8"
  • warranty: 1 year
  • Our 60-day money-back guarantee

What's in the Box:

  • 2 Woofers
  • 2 Grilles
  • 2 Grille rings
  • 2 Tweeters (each tweeter has an attached 5" length of wire)
  • 2 Crossovers with attached 19" input/output leads (the input leads have bare wire and the output leads are terminated with quick-slides)
  • 2 Flush-mount housings
  • 2 Angle-mount bases
  • 2 Angle-mount base trim rings
  • 2 Flush-mount retaining clips
  • 2 Tweeter back plates
  • 2 Self-adhesive foam cushions
  • Eight 1" self-tapping screws
  • Four 5/8" self-tapping screws (0.161" diameter)
  • Four 5/8" self-tapping screws (0.119" diameter)
  • Four 5/16" self-tapping screws
  • 4 Machine bolts
  • 4 Wing nuts
  • 12 Large speed clips
  • 4 Small speed clips
  • Instructions Manual
  • Warranty Card

Kenwood KFC-P605ie Reviews

Average Customer Review(s):

(5 Reviews)

Great Speakers for the Price

Chris from Montclair, NJ on 2/4/2006

These speakers are very balanced and neutral. They do have pretty good bass punch. The Crutchfield guide is wrong. These speakers will fit in an S2000 with no problems at all. The tweeters produce a full sound without being shrill. Overall I found these speakers to be a good value producing sound that compares favorably with speakers that cost more than double the price.



Kenwood Excellence Cruthfield Knowledge

Lloyd from Sikeston, MO on 9/18/2005

Crutchfield Customer Review (What's this?)

I added these speakers in my 1999 Chevy Silverado Ext. Cab (as front door replacements)along with the Kenwood KFC-4675C 4X6's (rear door replacements) and the Kenwood KAC-6401 30X4rms amp to push these remarkable speakers. The sound is excellent. Crisp highs, Slightly Modest mids. I also added a powered MTX Thunderform sub for the extra bang of bass. Excellent system for my budget. (superb sound inside, stealth outside)<BR> <BR>I gave these speakers only four stars only because I had to cut a second hole in my door panel to accomadate the tweeters as the original hole was to large, however this is all disquised under the original factory door screens anyway. The brakets for the woofers made them literally just a snap to change (excellent bracket from Crutchfield as always)Thanks<BR><BR>Very impressed, and well recomended.



Very Nice.

Pete from Wauregan, CT on 7/9/2005

Crutchfield Customer Review (What's this?)

I got these speakers because the Infinitys would Not fit.... The specs are pretty Much the same between the both. I was very Impressed with The sound quality Of these speakers. everything from rap to jazz To metal sounded great. No distortion at all. I run the speakers with a alpine cda-7893 V-power hybrid 60x4 (rms 27x4) Deck. <BR><BR>Pro's<BR>Good price<BR>Looks good<BR>Great Highs<BR>Great Mids<BR>Good lows (depending on the Enclosure you have them in)<BR>freq responce is excelent<BR>great Imaging<BR><BR>Cons<BR>None<BR><BR>I will Buy these speakers again



'01 Golf 2.0 Euro Spec

Killania from Bavaria, Germany on 6/5/2005

Installed two (2) Sets of these speakers plus the Kenwood Excelon KDC-X689 (the military PX offered these). The speakers are clean both cranked as well as low. The Bass reverberates and the highs are sharp. The mids are ok, but is to be expected. The crossover network has 3 settings(+5, 0, -5 ohms, but the custom install was inside the doors, so decide what you want beforehand (set mine +5), as they will be a challenge to get to later. Had to cut away some in the front for the tweeters and put the rear tweeters in the far back with custom front-facing mounts (the VW rear-door mounts are too shrill as they are right behind the driver's seat). No amp was needed to push these, as the MOSFET 50W x 4 met all my needs. I am ordering the KW 10" powered sub and will put it under the passenger seat (3 3/4" ht). All in all - extremely happy with these speakers! Total install of radio and speakers took about 2 hrs for professional install due to modding for front and rear tweeters. Also, had to cut out the hands-free cellphone, though the radio offers it. May re-do the install when I get back State-side.



Infinity lover buys Kenwood

Michael from Grand Rapids, MI on 2/24/2005

Bought these because Infinity components would not fit. Impressive, detailed highs with clear, smooth vocals. Angle mount at top of the door created excellent imaging. <BR><BR>-Very detailed highs (a little better than Infinity)<BR>-Good mids (not as "warm sounding" as Infinity)<BR>-Excellent imaging (more precise than Infinity)<BR>-Budget price ($128 refurbished vs. $200 for Infinity)<BR>-Low bass equal to Infinity (which is not very much)<BR>-Crank it up and everything stays clean<BR>-Even smooth tone throught frequency range<BR><BR>I am very happy with these and would buy them again.




Hands-on research

Features and Specs

Speaker Size
Design 2-way
Tweeter Design 3/4" Dome
Impedance (Ohms) 4
Tweeter Composition UFLC
Woofer Composition Pearl Mica IMPP
Woofer Surround Rubber
Parts Warranty 1 Year
Labor Warranty 1 Year
Sensitivity (1W at 1 meter) 91
Sensitivity at 2.83 volts N/A
Frequency Response 35 - 25k Hz
Minimum RMS Wattage 8
Maximum RMS Wattage 50
Peak Power Handling (Watts) 200
Top-mount Depth (Inches) 2 1/8
Bottom-mount Depth (Inches) N/A
Cutout Diameter or Length (inches) 4 15/16

Product Research



Woofers: The woofer cones are silver Pearl Mica Injection-Molded Polypropylene. Uniform pearl mica crystals form an overlapping structure that adds strength and heat resistance to polypropylene; the result is reduced distortion and improved reliability. Each woofer uses a rubber surround.

Mounting: The woofers can be mounted in a 6-1/2" opening, or, using the four mounting tabs, the woofers can be mounted in a 6-3/4" opening.


UFLC Soft Dome Tweeters: The 3/4" soft dome tweeters are made from Urethane Film Laminate Cloth for smooth highs and low distortion.

Image Enhancer: Each tweeter is equipped with Kenwood's patented Image Enhancer. Its smooth rounded surface eliminates most of the reflected sound waves that would interfere with the direct sound waves coming from the tweeter. The end result is a better dispersion pattern, less distortion, and clear high-frequency reproduction.

Tweeter Mounting Options: The tweeters may be flush, surface, or angle mounted.

  Flush Mount Surface Mount Angle Mount
Mounting Depth 1.171" 0.603" (screw depth) 0.549" (screw depth)
Mounting Height 0.361" 0.812" 1.744"
Cutout Diameter 1.755" N/A N/A
Frame Diameter 2.077" 1.564" 1.931"


2-Way Crossover Network: Each crossover features a 5 kHz high-pass filter for the tweeters and a 5 kHz low-pass filter for the woofers.

Input/Output Connections: The crossover input wires are terminated with bare wire and the output wires are terminated with quick-slides.

Mounting: There are two mounting tabs on each crossover.

Dimensions: L=4.827", W=1.787", H=1.063"

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.