Skip Navigation

Kenwood 150-watt Bass Package

Includes KAC-1502S 2-channel amplifier and two KFC-W110S 10" subwoofers

6 Reviews | 1 question - 2 answers

Item # 113PW1010

This item is no longer available.

Shop all Bass Packages

Overview

Our take on the Kenwood 150-watt Bass Package

This Kenwood "party pack" includes the KAC-1502S 2-channel amplifier and two KFC-W110S 10" subs — exactly the components you need to produce bold, punchy bass in your car. Just add an enclosure and wiring, and you'll enjoy strong low-frequency performance.

This Kenwood "party pack" includes the KAC-1502S 2-channel amplifier and two KFC-W110S 10" subs — exactly the components you need to produce bold, punchy bass in your car. Just add an enclosure and wiring, and you'll enjoy strong low-frequency performance.

Loud and clear
Each KFC-W110S 10" subwoofer sports an injection-molded polypropylene cone with a thick urethane surround, a combination that promotes deep excursion and accurate bass response. Each sub handles up to 175 watts RMS, and can be mounted in a sealed or ported box.

Rugged power
Kenwood's tough KAC-1502S 2-channel amplifier powers the two subs comfortably with 150 watts in single-channel mode. A low-pass filter directs the correct frequencies to the subs, giving you plenty of bass without distortion. You'll finally hear and feel the low-frequency notes your car's full-range speakers can't play.

Important Note: The power of the amp in this bass package is significantly less than the manufacturer's recommended power handling for the included sub(s). It's OK to underpower your subs, as long as you set the amp's gain controls properly to avoid distortion. This diagram shows you how to wire up the sub(s) in this package.

Was looking for a little upgrade on the cheap for my 2005 mustang and it was well worth the money.

Dantrin, Falconer, NY

What's in the Box:

  • This Kenwood Amp/Sub Package contains three individually packaged items in one larger box: a KAC-1502S Amplifier and two KFC-W110S Subwoofers
  • The KAC-1502S Box includes:
  • 2-Channel amplifier
  • 25 amp ATO fuse (installed)
  • 7.5" Speaker-level input harness
  • Four 5/8" Self-tapping screws
  • Instruction manual (English/ French/ Spanish)
  • Warranty information
  • Each KFC-W110S Subwoofer box includes:
  • 10" SVC 8-ohm woofer
  • Eight 1" Self-tapping screws
  • Self-adhesive foam gasket
  • Instruction manual
  • Warranty information

Product Highlights:

  • package includes Kenwood KAC-1502S 2-channel amplifier and two KFC-W110S 10" subwoofers
KAC-1502S 2-channel amplifier
  • 60 watts RMS x 2 at 4 ohms (150 watts x 1 bridged at 4 ohms)
  • CEA-2006 compliant
  • fixed low-pass filter (80 Hz at 18 dB per octave)
  • preamp and speaker-level inputs
  • requires 10-gauge power and ground leads — wiring and hardware not included with amplifier
  • 9-1/8"W x 2-3/16"H x 7-1/8"D
  • warranty: 1 year
KFC-W110S 10" 8-ohm subwoofers
  • injection-molded polypropylene woofer cone with high-roll urethane surround
  • black stamped-steel basket
  • power range (per sub): 45-175 watts RMS (700 watts peak power)
  • frequency response: 35-1,000 Hz
  • sensitivity: 90 dB
  • top-mount depth: 4-7/8"
  • sealed box volume (per sub): 1 cubic foot
  • ported box volume (per sub): 1-1/4 cubic feet
  • warranty: 1 year
  • Our 60-day money-back guarantee
Reviews

Kenwood 150-watt Bass Package Reviews

Average Customer Review(s):

(6 Reviews)
rewards card

Submit a review and enter to win a $350 rewards card

Review this product

Thanks for submitting your review

Most reviews are processed and published within 5 business days. You will receive a confirmation email once your review has been published.

Your Review

Use the stars below to rate the overall product on a scale of 1-5
1500
Upload your photos

Not visible. Email associated with order.
(e.g., Charlottesville, VA)

Additional Fields (optional)

500
500

By submitting this review, you agree to our terms and review guidelines.

Filter by rating

Customer photos


<< >>
Details

Hands-on research

Product Research

Amplifier
Subwoofers

Amplifier

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4-ohm load, with 1% or less Total Harmonic Distortion plus noise (THD+N), and over a frequency range (for full range amplifiers) of 20 Hz to 20,000 Hz. Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4 ohms. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples). The Kenwood KAC-1502S under CEA-2006 regulations is rated at 60 Watts RMS x 2 channels with an 80 dBA signal to noise ratio. The signal to noise ratio at the rated power output (not CEA-2006 conditions) is 95 dB.

2-Ohm Stable: The amplifier can support a 2-ohm load in stereo; the 2-ohm power output is 75 watts RMS x 2 channels.

Bridgeable: This two-channel amplifier can be bridged to a 4-ohm mono load; the bridged output is 150 watts x 1 channel RMS.

Cast Aluminum Heat Sink: The KAC-1502S utilizes a cast aluminum heat sink design to ensure the amplifier stays cool.

Protection circuitry: The amplifier features protection circuits that will turn the amp off in case of the following events:

  • speaker output contacts ground
  • speaker wire short-circuits
  • unit malfunctions and DC is sent to speaker output

Power Indicator: When the amplifier is turned on the Power indicator (on top of the amp) lights up red. This indicator turns off with the amplifier, and will turn off if the amplifier goes into protect mode.

Gain Control: To accommodate the varying range of signal levels from today's factory and aftermarket radios, the KAC-1502S features an adjustable gain control; 0.2-5.0 volts (RCA).

Low Pass Crossover: The amplifier has a fixed 80Hz, -18dB/oct low-pass filter which can be turned On or Off.

Power Connections: The power, ground, and remote turn-on connections are 0.35" wide screw terminals. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are recommended. Minimum 10 gauge wire is required for power and ground.

Speaker Outputs: The two pair of speaker outputs are 0.35" wide screw terminals. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors are also recommended for the speaker wires.

Note: The speaker output terminals can be used in stereo or bridged mode.

Line Level Input: The line input is a pair of stereo RCA jacks.

Speaker Level Input: A harness is included for the speaker level input. The input harness is common ground; it will not accept floating ground outputs.

Fuse: The amplifier uses a 25-amp ATO blade-type fuse.

Subwoofers

Woofer: The cone is constructed of polypropylene which is lightweight, efficient, and durable.

Surround Material: The woofer utilizes a high excursion urethane foam for added durability and better bass performance.

Basket: The woofer features a black stamped-steel basket for added rigidity.

Enclosure Compatibility: The KFC-W110S can be mounted in either a sealed or ported enclosure:

  • Sealed Box Volume: The recommended sealed box sizes range from 0.6 cu/ft to 1.5 cu/ft, the ideal size being 1.0 cu/ft.
  • Ported Box Volume: The recommended ported box sizes range from 0.75 cu/ft to 1.75 cu/ft, the ideal size being 1.25 cu/ft using a 3" diameter x 7" long port.

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Accessories
Q & A

Customer Q&A

1 question already asked

If you use the speaker foam that you stuff inside of the Sub-Woofer enclosure, then you'll get better deeper bass response. It will fake out the woofer and it will work and sound great. R. [ RICKY  Feb 06, 2014 ]
Yes, you can, it will raise the system "Q" but you shouldn't notice the difference, unless you're measuring with audiophile instruments like an RTA. [ CARLFRED A  Feb 03, 2014 ]
Articles