Tiltable 3" LCD Screen: The Sony Cyber-shot DSC-RX10M2 digital
camera has a 3.0" Xtra Fine LCD screen with 1,228,800 dots. The
LCD brightness control can be set to Auto, Manual (-2 to +2), or Sunny Weather
(appropriate for shooting outdoors). You can tilt the LCD upward approximately
180° for shooting low angles and self-portraits, and downward approximately 45°
for high angles.
OLED Viewfinder: In addition to the 3" LCD screen, the
camera is equipped with a 0.39" XGA electronic OLED viewfinder with 2,359,296
dots. The viewfinder has a -4.0 to +3.0m-1 diopter adjustment to
adjust it to your eyesight. An eye sensor next to the viewfinder will
automatically turn on the viewfinder and turn off the monitor when you raise the
camera to your eye. In the menu, you can manually choose the viewfinder or the
Recording Media: The camera is compatible with the following recording media: Memory Stick Duo
(still images only), Memory Stick PRO
Duo (Mark 2 only for movie recording), Memory Stick Pro-HG Duo, SD, SDHC, and SDXC memory cards
(UHS-I U1 compatible, Class 10 or higher). For recording 4K movies, SDXC memory
cards with a capacity of 64 GB or more with an SD Speed Class of 10 or UHS Speed
Class 1 is required. If recording in 100 Mbps or more, UHS Speed Class 3 is
Image Recording Formats: The camera records still images in
JPEG (with Extra Fine, Fine, and Standard compression), RAW (unprocessed), and JPEG+RAW
formats (images from both formats created at the same time). Moving images can be recorded in
XAVC S (MPEG-4 AVC/H.264 with 2-channel LPCM audio), AVCHD Ver. 2.0 format (MPEG-4 AVC/H.264 with Dolby Digital 2ch audio) or
MP4 (MPEG-4/H.264 with 2-channel AAC
Image Sensor: The camera
is equipped with the world's first 1.0-type stacked CMOS image sensor with DRAM
chip that enables up to 40x super slow motion and up to 1/32000 sec
super-high-speed shutter. This 13.2 x 8.8mm (1") 20.1MP Exmor RS CMOS image sensor with approximately
and 20.2-million effective pixels and a 3:2 aspect ratio. Paired with the image
sensor is the high speed BIONZ X image processor.
Lens: The camera is equipped with a bright Carl Zeiss Vario-Sonnar
T* (T-star) 8.3x zoom lens. It has a focal length of 24-200mm (35mm equivalent/3:2
for recording still images, and 26-212mm for recording 16:9 movies. The maximum aperture is
F2.8 across the zoom range, while the minimum aperture is F11 or F16 depending
upon the shooting mode.
Shutter Types: The RX10M2 offers both a mechanical shutter
and an electronic shutter. The Shutter Type settings are as follows:
- Auto: The shutter type is automatically switched based
on the shooting conditions and shutter speed.
- Mechanical Shutter: The camera operates with the
mechanical shutter only. The shutter speed can be set from 30 seconds to
1/3200 second, plus Bulb. Both the mechanical and electronic shutter sounds
are heard. The electronic shutter sound can be turned off, if desired.
- Electronic Shutter: The camera shoots with the
electronic shutter only. The shutter speed can be set from 30 seconds to
1/32000 second. Only the electronic shutter sound is heard, and can be
turned off, if desired.
Zooming: In addition to the 8.3x optical
zoom, you can reach higher zoom scales by engaging the Smart Zoom, Clear Image Zoom or the
Digital Zoom. Smart Zoom enlarges images without causing deterioration of the
image by partially cropping the image (available when the image size is set to
Medium, Small, or VGA). Clear Image Zoom uses an image process with less
deterioration. Clear Image Zoom magnifies the image up to 16x (Large image
size). Digital Zoom obtains a higher zoom, but with some image deterioration.
Digital Zoom magnifies up to 33x (Large image size).
SteadyShot: Sony's SteadyShot image stabilization can help
you obtain blur-free movies and still images. SteadyShot utilizes optical
camera-shake compensation supplemented with electronic anti-rolling type image
stabilization for even sharper images. There are three levels of SteadyShot for
movies: Intelligent Active, Active, and Standard. For still images, SteadyShot
can simply be turned on or off.
Still Image Sizes: When recording digital still
images, the DSC-RX10M2 allows you to choose from multiple image sizes
in four aspect ratios: 3:2 (for printing), 16:9 (for viewing on an
HDTV), 4:3 (for viewing on a computer), and 1:1 (for shooting as a
medium format camera). The following image sizes
|3:2 ||16:9 ||4:3 ||1:1 |
|20M 5472 x 3648 ||17M 5472 x 3080 ||18M 4864 x 3648 ||13M 3648 x 3648 |
|10M 3888 x 2592 ||7.5M 3648 x 2056 ||10M 3648 x 2736 ||6.5M 2544 x 2544 |
|5M 2736 x 1824 ||4.2M 2720 x 1528 ||5M 2592 x 1944 ||3.7M 1920 x 1920 |
| || ||VGA 640 x 480 || |
Sweep Panorama: You can record multiple images while
moving the camera in an arc, either horizontally or vertically. You can choose
the direction to pan the camera while taking the images. These images can
be compiled into a single panoramic image, and played back on an HDTV. The available image
- Vertical: 3872 x 2160
- Horizontal: 8192 x 1856
- Vertical: 5536 x 2160
- Horizontal: 12416 x 1856
Recording Movies: Besides recording still images, the RX10M2 can also record pro-quality movies, including 4K and Full HD. You can
record movies in the low-compression, high-quality XAVC S format, AVCHD for easy
editing and sharing, or MPEG-4 for uploading to your favorite social media sites.
You can choose between NTSC (60, 30, 24 fps) and PAL (50, 25 fps) for worldwide
image sizes and movie quality include:
|Movie Format ||Image Quality ||Avg Bit Rate ||Image Size |
|XAVC S 4K ||30p/25p/24p ||100 Mbps ||3840 x 2160 |
|30p/25p/24p ||60 Mbps |
|XAVC S HD ||60p/50p/30p/25p/24p ||50 Mbps ||1920 x 1080 |
|120p/100p ||100 Mbps |
|120p/100p ||60 Mbps |
|AVCHD ||PS 60p/50p ||28 Mbps ||1920 x 1080 |
|FX 60i/50i/25p/24p ||24 Mbps |
|FH 60i/50i/25p/24p ||17 Mbps |
|MP4 ||60p/50p ||28 Mbps ||1920 x 1080 |
|30p/25p ||16 Mbps |
|30p/25p ||6 Mbps ||1280 x 720 |
Note: The camera's 4K movie recording function
allows you to record a maximum of 29 minutes of 4K movie footage
in one shot.
Dual Video Recording: When recording a movie, you can choose
to simultaneously record an XAVC S movie and an MP4 movie, or an AVCHD movie and
an MP4 movie.
Built-in Wi-Fi/NFC: The RX10M2 lets you connect wirelessly
with smartphones and tablets via Wi-Fi and NFC (near field communication). Using
the PlayMemories Mobile app, available for Android 2.3 and up from Google Play
and for iOS 4.3 and up from the App Store, you can send images to, or control
your camera from your smartphone or tablet. When connected to a Wi-Fi network,
you can send images to your computer or view on a Wi-Fi-enabled TV.
Customizable Function Button: The camera features a Function
button that allows you to assign functions for up to 12 functions for quick access.
When the Function button is pressed, two rows of six presets are displayed,
allowing you to access any of the functions. There are 35 overall functions to
choose from to fill the 12 function presets.
Memory Recall: The Memory Recall mode can memorize up to
three groups of the user's preferred settings. Settings include zoom
magnification, white balance, exposure compensation, date, and grid lines. This
enables you to quickly switch the settings at the right moment.
Drive Modes: The camera offers multiple Drive Modes. In
addition to single image shooting, you can choose from the following:
- Continuous Shooting: The camera shoots continuous
images at approximately 5.5 frames per second while you press and hold down the shutter release.
- Speed Priority Continuous: Shoots full 20.1 megapixel
images continuously at up to 14 frames per second while you press and hold
the shutter release button.
- Self-Timer: You can set the
Self-Timer mode to a 10-second, 5-second, or 2-second delay so you can be in the
- Self-Timer Continuous: The Self-Timer Continuous shooting mode
takes continuous frames after a 10-, 5-, or 2-second delay. You can choose 3
or 5 frames to be taken.
- Continuous Bracket: The Continuous Bracket mode lets
you shoot a series of 3, 5, or 9 images with a single press of the shutter
button, each with a different exposure
setting--some at normal exposure, some under exposed, and some over exposed.
You can choose from five different step
values: 0.3 EV, 0.7 EV, 1.0 EV, 2.0 EV, or 3.0 EV.
- Single Bracket: The Single Bracket offers the same
choices as the Continuous Bracket above, however, you must press the shutter
release button for each picture.
- WB Bracket: The WB Bracket mode shoots three images, each with
different color tones according to the selected settings of white
balance, color temperature, and color filter. You can choose the a low or
high bracket deviation value.
- DRO Bracket: The camera shoots a total of three images,
each with a different degree of D-Range Optimizer.
Auto Focus Areas: You can select from the following auto focusing
- Wide: The camera focuses in all ranges of the
finder frame automatically. When you press the shutter button halfway, a
green frame is displayed around the area that is in focus.
- Center: The camera focuses on a subject in the center of the
frame. By pressing the shutter release halfway, you can lock the focus on
your subject and recompose your shot with the subject off center.
- Flexible Spot: The camera focuses on a very small area
that can be moved around the frame to the desired point on the screen.
- Expand Flexible Spot: If focus isn't obtained on the
single selected point, you can use focus points around the flexible spot as
the second priority area to achieve focus.
- Lock-on AF: When the shutter button is pressed and held
halfway, the camera tracks the subject within the selected autofocus area.
Manual Focus: When it is difficult to get the proper focus
in auto focus mode, you can switch to Manual Focus. When in Manual Focus, the
manual ring around the ring can be rotated to achieve sharp focus. Manual Focus
is available for still images and movies. Direct Manual Focus (DMF) lets you
make fine adjustments manually, using the focus ring, after the focus has been
AF Illuminator: The AF (auto
focus) Illuminator briefly provides fill light to focus more easily on a subject
in dark surroundings. The red AF Illuminator lights when the shutter button is
pressed halfway. You can set the AF Illuminator to Auto or Off.
Face Detection: Face Detection technology detects up to
eight individual faces and controls flash, focus, exposure, and white balance to
deliver accurate, natural skin tones with reduced red-eye. It can also give
priority to children or adults. You can also select and register an individual's
face to be given priority.
Smile Shutter Mode: The Smile Shutter technology
automatically detects and captures a smiling face. Simply activate by pressing
the Smile Shutter button and the camera will capture a smile the moment it
happens. You can adjust the degree of Smile Detection
Sensitivity as desired.
Scene Recognition: Scene Recognition is used in the
Intelligent Auto and Superior Auto shooting modes. This function automatically detects different types of scenes and selects the appropriate camera settings:
Portrait, Infant, Night Portrait, Night Scene, Backlight Portrait, Backlight,
Landscape, Spotlight, Low Light, and Macro. The camera also recognizes certain
conditions and makes appropriate adjustments: Tripod, Walk, Move, Move (bright),
or Move (dark).
Shooting Modes: Using the top-mounted Mode Dial, you can
select from the following shooting modes:
- Auto Mode: The Auto Mode allows you to shoot still
images under any condition with good results by setting the values
determined by the camera. You can choose between two Auto Modes:
- Intelligent Auto Mode (iAuto): Allows you to shoot
still images with automatic scene recognition.
- Superior Auto Mode (iAuto+): Allows you to shoot still
images with automatic scene recognition, with an emphasis on dark or backlit
- Program Auto: Allows you to shoot with the exposure adjusted
automatically (both the shutter speed and aperture value). You can also
select various settings using the menu. While shooting in Program Auto, you
can change the shutter speed and aperture combination without changing the
exposure (Program Shift).
- Aperture Priority: You can shoot still images after
adjusting the aperture setting manually. The camera will determine the
- Shutter Priority: You can shoot still images
after adjusting the shutter speed manually. The camera will determine the
- Manual Exposure: You can set the exposure manually. The shutter speed can
be set between 1/2000 and 30 seconds. The aperture (F value) can be set
between F1.8 and F11 (Wide Angle) or between F2.8 and F11 (Telephoto).
- Memory Recall: You can set and store often-used modes
and numeric settings for recall at a later time.
- Movie Mode: Allows you to record XAVC S, AVCHD or MPEG-4 movies with
- HFR (High Frame Rate): This mode allows you to shoot
slow motion movies. You can select frame rates of 240 fps, 480 fps, 960 fps
(NTSC) and 250 fps, 500 fps, and 1000 fps (PAL). The playback speed varies
depending on the set frame rate and record setting.
- Sweep Panorama: Multiple images are shot while
the camera is moving, and these images are compiled into a single panoramic image.
- Scene Selection Modes: You can choose from the following Scene Selection modes:
Portrait, Sports Action, Macro, Landscape, Sunset, Night Scene, Hand-held
Twilight, Night Portrait, Anti-Motion Blur, Pet, Gourmet, Fireworks, and High Sensitivity.
Note: The Program Auto, Aperture Priority, Shutter
Priority, and Manual shooting modes are available for movies as well as
Besides auto exposure, you can adjust the exposure from +3.0EV to
-3.0EV in 1/3 stop increments.
Built-In Flash: The camera's built-in flash
features a range of 3.28'
to 33.46'. With the ISO Speed set at 12800, the range increases to 66.93'. The flash
- Autoflash: the flash automatically strobes when the surroundings are
dark or when there is backlight
- Fill Flash: the flash strobes with every shot
- Slow Sync: the flash is used regardless of the amount of
ambient light, but the shutter speed is slower under dark conditions,
allowing you to clearly shoot a background that is out of the flash-lit
- Rear Sync: the flash operates before exposure is
completed every time your trigger the shutter
- Wireless: You can attach a remote control-compatible
external flash (sold separately) and a separate wireless flash placed away
from the camera.
- Off: the flash does not operate
Multi Interface Shoe: The DSC-RX10M2 is equipped with a
Multi Interface Shoe which offers an advanced interface for connecting an
external flash (HVL-F20M,
HVL-RL1) or mounting an external microphone.
Red-eye Reduction: The flash pre-strobes before shooting to
reduce the red-eye phenomenon. You can set to On or Off.
Metering Modes: You can select from the following Metering
- Spot Metering: Spot metering lets you adjust the
exposure to the subject, even when the subject is a backlit or when there is
strong contrast between the subject and the background.
- Center-weighted Metering: Center-weighted metering
measures the center of the image and determines the exposure based on the
brightness of the subject.
- Multi-pattern Metering: When multi-pattern metering is used, the image is
divided into multiple regions and metering is performed in each region. The
camera judges the subject position and background brightness, and determines a
White Balance: When the white balance is set to auto, the
white balance is set automatically in response to the condition of the subject,
and the overall color balance is adjusted. When shooting under special lighting
conditions, you can select the settings manually. When using flash, you can
select the flash white balance mode. The white balance can also be set to
Daylight, Shade, Cloudy, Incandescent, Fluorescent (warm white), Fluorescent (cool white), Fluorescent (day white),
Fluorescent (daylight), Flash, Color Temperature/Filter, Custom
(adjust white balance depending on the light source) or Custom Set (memorizes
the basic white color which will be used).
Grid Lines: The cameras
on-screen grid lines make it easy to set a subject's horizontal and vertical
position. You can choose from three grid line overlays: Rule of 3rds, 4x6 Square,
and Diagonal + 4x6 Square.
Histogram: A histogram is a graph showing the brightness of an image.
The graph display indicates a bright image when skewed to the right side, and a
dark image when skewed to the left side.
In-camera Guide: An
on-screen function guide text/icon display makes it easy to learn the camera
functions that give you greater creative freedom to adjust photo settings. The
function guide can be turned on or off as desired.
Folder View Modes: The Sony DSC-RX10M2's View Mode allows
you to select your recorded images and movies by sorting them into the following folders:
Date, Still, MP4, AVCHD, XAVC S 4K, and XAVC S HD.
Index View: In addition to viewing images one-by-one in full
screen, you can view multiple images at once in the index view mode. The index
feature lets you to display a total of 9 (3 x 3) or 25 (5 x 5) images at once.
Slide Show: The Slide Show function lets you play back
images one after the other. The interval between the pictures can be adjusted,
allowing you to choose 1, 3, 5, 10, and 30 seconds. When repeat
is selected, the images are replayed in a continuous loop.
Playback Zoom: You can enlarge a recorded still image up to
8x the size of the original image. Once the image is zoomed, you can pan left
to right and up or down through the image.
Rotating Images: Recorded images can be rotated 360-degrees in
90-degree increments on the camera's LCD screen.
Picture Effect: You can add effects to images to make them
look more impressive and artistic. You can choose from the following: Toy
Camera, Pop Color, Posterization, Retro Photo, Soft High-key, Partial Color,
High Contrast Mono, Soft Focus, HDR Painting, Rich-tone Mono, Miniature,
Watercolor, and Illustration.
Images: You can delete a selected
image, or you can delete all the unprotected images at once. In order to avoid
accidentally deleting of an image, it can be protected.
Print Mark: You can place a print mark on still images recorded with this camera. This mark
is convenient when you have images printed at a shop that conforms to the DPOF
(Digital Print Order Format) standard.
Battery Information: The DSC-RX10M2 is powered by the
NP-FW50 Lithium-ion rechargeable battery. Using the supplied AC-UD10D AC
adapter, the battery can be fully charged in the camera in approximately 310 minutes. Under normal operating conditions, the
battery has the following capacity:
| Function ||Battery Life |
Images ||LCD ||Approx. 400 images |
|Viewfinder ||Approx. 360 images |
| Viewing Still Images ||Approx. 315 min or 6300 images |
| Recording Movies |
|LCD ||Approx. 65 min |
|Viewfinder ||Approx. 65 min |
| Recording Movies |
|LCD ||Approx. 130 min |
|Viewfinder ||Approx. 135 min |
Internal Battery: The camera has an internal rechargeable
battery for maintaining the date and time and other settings regardless of
whether the power is on or off. The battery is continually charged as long as
you are using the camera. If the camera isn't used for about a month, the
internal battery can become discharged. The camera can still be used with a
discharged internal battery, however, the date and time will not be shown. The
internal battery can be fully recharged in approximately 24 hours with the power
off and a charged battery pack is in the camera.
HDMI: The RX10M2 has a Micro HDMI (Type D) output on the
of the camera for connecting the camera to an HDTV. A Micro HDMI-to-HDMI cable is
required to make the connection. If you are connecting to a Sony Bravia TV with
Bravia Sync, you can control the camera using the TV's remote control.
Multi/Micro USB : The camera features a single Micro USB jack
(labeled "Multi") on the left side of the camera for connecting the supplied USB cable for
downloading your photos to your computer or printer, or charging the battery in
the camera. The interface is USB 2.0 High Speed compatible.
Microphone: A 3.5mm jack is provided for connecting an
external microphone. If the external mic requires plug-in power, the jack will
supply power to the mic. The built-in microphone will be muted when an external
mic is plugged in.
Headphones: A 3.5mm stereo headphone jack is provided for
monitoring audio during recording or playback.
PlayMemories Home: The DSC-RX10M2 can be used with
PlayMemories Home software, which needs to be downloaded and installed on your computer. "PlayMemories Home" software is downloadable from
the Sony Imaging website (The URL is printed in the Instruction Manual). It
is compatible with Windows 8/8.1, Windows 7 (SP1), and Windows Vista (SP2),
and Mac OS X 10.7-10.10 operating systems only. With PlayMemories Home you can:
- Manage and edit photos and videos on your PC or Mac
- Organize photos and videos
- Upload photos to a cloud service for storage (PlayMemories Online)
- Search for photos and videos using Calendar View
- Import and Export photos and videos, plus create disks and print.
- Perform basic editing functions
- View photos and videos on a map (using location information from a
- Create multi-view videos
PlayMemories Camera Apps: The RX10M2 is compatible with
PlayMemories Camera Apps, which enables you to add new features to the camera by
downloading a new app and installing it in the camera. Apps are available to fit
your shooting style, including portraits, close-up photography, sports, time
lapse, etc. Many apps are available via a free download, while more advanced
apps require a fee of $4.99 or $9.99.
Image Data Converter: Image Data Converter software is
required to display and process images recorded in RAW format. You can also
adjust the brightness or color, as well as "develop" the RAW image files into
JPEG or TIFF files. Image Data Converter can be downloaded to your computer, using a URL printed in the
manual. Image Data Converter is compatible with Windows 8/8.1, Windows 7 (SP1),
Windows Vista (SP2), and Mac OS X 10.6-10.10.
Remote Camera Control: Remote Camera Control software allows you to
control a camera connected to your computer via a USB cable. Remote Camera
Control is compatible with Windows 8/8.1, Windows 7 (SP1), Windows Vista (SP2), and Mac
OS X 10.7-10.10.
Capture One Express (for Sony): The Sony RX10M2 is
supported by Capture One Express (for Sony) by Phase One. One of the world's
best RAW converters, Capture One Express (for Sony) delivers clear, detailed
images with accurate colors. You can make adjustments to the RAW image files,
convert the images to black & white, or use the HDR (High Dynamic Range) tool to
pull out details in over- or under-exposed images. Capture One Express (for
Sony) is available for a free download. A pro version can be purchased for even
more processing tools.