Why Choose Crutchfield?
Great gear and expert advice
Our experts help you pick the ideal gear for your needs.Meet our advisors
Free tech support for the life of your gear.Read about our one-on-one expert help
You may return items that are complete and like new for any reason within 60 days.See the details of our return policy
Earn one point for every dollar you spend and use those points to save on future purchases.Get full details on Crutchfield Rewards
Deep discounts on car installation gear
We offer vehicle-specific installation instructions, dash kits, wiring harnesses, and speaker accessories at deeply discounted prices with car stereo and speaker purchases. Available for most vehicles.Learn more
Trusted since 1974
Our customers have trusted us with their business, and they’ve helped us win awards for our service.Check out our most recent awards
The manufacturer’s warranty always applies.See more details
Lightning Audio LSD10DT-03
Strike 1-farad Cap. w/Distribution Top
Item # 495LSD10D3 | MFR # LSD10DT-03
This item is no longer available.
Our take on the Lightning Audio LSD10DT-03 by Crutchfield's Erin Blanton
Do your headlights flicker when the bass hits hard? Does your bass start out strong, and then fade into mush after a minute or two? Car batteries are slow to deliver the kind of power your amps need to give you tight, powerful bass hits. Lightning Audio capacitors eliminate that problem by storing reserve power and then delivering it when your amps need it most. That's why you see external capacitors in just about every stereo competition vehicle and you don't see dimmed headlights.
Lightning Audio's Strike Caps act as a buffer zone between your amp and your battery, getting the juice to your bass for maximum performance. The LSD10DT-03 1-farad cap is perfect for a two amp setup. It has a built-in distribution block that has one input and two outputs for your power rings. The digital voltage readout shows your exact voltage to the decimal point. Visual and audible warnings tell you if the cap has been wired backwards.
Note: The capacitor is installed on the power cable that connects the amplifier to your vehicle's battery. You will need a short length of ground cable and crimp-on connectors (not included) to install the capacitor. One length of power cable connects from your battery to the capacitor's positive terminal, while separate lengths of power cable connect from the capacitor's built-in distribution block to your amplifiers. The ground cable is used to connect the capacitor's negative terminal to the chassis of your vehicle.Details:
- 1-farad cap for systems of up to 1,000 watts RMS
- built-in distribution block (one 4-gauge input, one 4-gauge output, one 8-gauge output)
- digital voltage readout
- 16-volt maximum (20-volt surge)
- 3-1/16" diameter x 9-3/4"H
- 1-year warranty
What's in the Box:
- 1 Farad capacitor with digital display and distribution top
- 2 Plastic mounting bracket (Top bracket is incorporated into distribution top)
- CHRG2 Charging/discharging card
- Installation and Application Manual
- Warranty info card
- Caution info card
Overview: The overall response of your audio system will be enhanced with the use of capacitors due to their ability to quickly supply a large amount of current to your amplifier's power supply during high current demand (low bass). This makes the Lightning Cap a logical addition to your system due to the fact that automotive electrical systems aren't designed to deliver the current to satisfy the requirements of high-powered audio components. It can also filter AC voltage induced in the system by the amplifier's power supply which could cause objectionable noise. A one Farad capacitor is recommended for each 1000 watts of amplifier power, although you can never have too much capacitance for any system.
LED Digital Display (With Auto Turn-On): The capacitor's monitor top features a blue digital LED display. The current DC voltage readout appears on the 1" x 1/2" display. The display senses voltage fluctuations during normal operation and turns itself on. After 5 minutes of non-use (no fluctuation), the display automatically reverts to sleep mode.
Distribution Cap: The capacitor's unique distribution cap has two 4-gauge and one 8-gauge set screw terminals on each post, allowing you to easily wire the capacitor into your audio system's power wiring without the use of power rings. The set screws require 5mm and 5/32" Allen wrenches (not supplied).
Equivalent Series Resistance (ESR): The Lightning cap is able to deliver its power quickly because its super-low ESR. Each capacitor has up to 18 ultra-sonically-cold welded tabs that connect the foil winding to the terminals at the top of the capacitor with almost no resistance.
High Gain Foil: Lightning capacitors use a high-gain foil. High-gain foil is created by passing the foil through several high-current (10,000 amp) chemical baths that "etch" the foil and create surface area. This allows for more capacitors in a smaller area.
Through-Post Design: The monitoring circuit is wired in parallel with the capacitor, not adding any resistance or inductance which could prevent the cap from doing its job.
Reverse Voltage Warning: A buzzer will sound if the capacitor is connected backwards.
Mounting Brackets: The Lightning cap is equipped with two translucent plastic mounting brackets. The brackets allow the cap to be mounted in virtually any position on a vertical wall or a horizontal surface.
Installation: In addition to the wires and connectors for your amp installation, you will need additional short lengths of ground wire and power wire to properly install the capacitor. One length of power wire connects from your battery to the capacitor's positive terminal, while a separate length of power wire connects from the capacitor's positive terminal to your amplifier. (It is recommended that the capacitor be wired no less than 18" from the amplifier.) The ground wire connects from the capacitor's negative terminal to the chassis of the vehicle.
- Size: 1 Farad
- VDC: 16V, 20V surge
- ESR: < 0.00198 ohm at 120Hz 25°C
- Terminals: Two 4-gauge and one 8-gauge set screws per terminal
Our Product Research Team
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.