About the Alpine KTP-445 Power Pack
The KTP-445 connects to any 2005 and newer Alpine headunit that uses a black power harness. It will not work with the CDE-100 receiver.
Want a simple way to kick up the power of your Alpine receiver? Alpine's "Power Pack" amplifier increases your receiver's power output to 45 watts RMS power by 4 channels — plenty of power to drive high-performance speakers or keep up with a big subwoofer amplifier. Best of all, you install the compact Power Pack by plugging it directly into your Alpine receiver's wire harness — no extra wires to run, and no other connections needed.
Note: The KTP-445 Power Pack won't work in systems where an outboard factory amplifier is still active. You'll have to bypass the factory amp if you want to upgrade your power with the KTP-445. Please contact an Advisor at 1-888-955-6000 to check compatibility if you have any questions.
Product highlights:
- plug-and-play compact Class D amplifier for Alpine in-dash receivers
- 4-channel amplifier
- 45 watts RMS x 4 at 4 ohms (CEA-2006 compliant)
- selectable gain switch (high/low)
- fuse: 15A
- 2-9/16"W x 1-1/2"H x 7-13/16"D
- warranty: 1 year
- MFR # KTP-445
What's in the box:
Alpine KTP-445 Power Pack owner's manual
- Head Unit Power Pack (45W x 4 RMS) with attached 38" harness terminated by a male Alpine connector on one end and an attached 29" harness terminated by a female Alpine connector on other end
- Instructions
Featured video:
Customer reviews for Alpine KTP-445 Power Pack
Loading...
Loading reviews...
Average review:
4.5 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Alpine KTP-445 Power Pack
Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
45 x 4 | |
Peak Power Output (Watts x Channels) | --- | |
Power at 2 Ohms (Watts x Channels) | N/A | |
Power at 1 Ohm (Watts x Channels) | --- | |
Bridged Power (Watts x Channels) | N/A | |
Minimum Impedance Bridged | N/A | |
Minimum Impedance Unbridged | 4 | |
Minimum Impedance | 4 | |
Best Frequency Response | 20-20k Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | N/A | |
Input Voltage | 14.4v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | N/A | |
Low-Pass Slope (dB/octave) | N/A | |
High-Pass Crossover Frequency | N/A | |
High-Pass Slope (dB/octave) | N/A | |
Bass Boost | No | |
Bass Boost Frequency | N/A | |
Fan Cooled | No | |
Fuse Rating | 15 | |
Speaker Level Inputs | --- | |
Preamp Outputs | No | |
Width (inches) | 2-5/8 | |
Height (inches) | 1-1/2 | |
Depth (inches) | 7-13/16 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year |
Product Research
Features
Overview: The Alpine KTP-445 Head Unit Power Pack is an easy-to-install power upgrade amplifier that allows you to add higher output and more dynamic response to your Alpine headunit. The KTP-445 amplifies your Alpine headunit's power output, resulting in a 150 percent power increase over the original power from the headunit's built-in amplifier.
Compatibility: The KTP-445 connects to any 2005 and newer Alpine headunit that has a black power harness. Please check with your Crutchfield Product Advisor to confirm compatibility.
Installation: Since the KTP-445 is small and compact, it installs behind your Alpine headunit in the dash of most vehicles. Its plug-and-play connections keep it simple, without requiring additional wiring or special tuning. The male harness connects to the rear plug on your Alpine headunit while the female harness plugs into your Alpine headunit's harness (included with your Alpine headunit). Then connect the wires from the Alpine headunit's harness to your factory harness adapter (sold separately).
Note: The factory radio circuit needs to be a minimum of 15A. If it is not, a separate power and ground will need to be installed for the KTP-445.
Controls: A high/low gain switch on the bottom of the amplifier allows for proper gain settings, whether or not a subwoofer is part of the system.
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
Wired this power pack up to my existing pioneer stereo with four alpine type-s speakers, couldn't be happier! I can turn my volume to 5/6 and no distortion, just clear music. Recommend this to anyone.
MarcL from Minneapolis, MN