Features Controls Connections
PDX Amplifier Design: Class-D amplifiers boast higher
efficiency, produce much less heat, and draw less current than traditional
Class-AB amps. The PDX series is Alpine's super-efficient power density design
of full-range and monoblock class-D amps. They combine MOSFET power supplies,
MOSFET final outputs, and a thermal management processor, along with a 6-Layer
Glass Epoxy PC Board to create a high-end sound quality without the bulky heat
sinks required by most amps with this much power.
STAR Topology: Alpine's unique STAR (Signal Transit for
Accurate Response) Circuit PCB design provides a single common ground for all
amp sub-blocks, preventing ground interference and minimizing internal noise.
Power Management Processor: The Alpine PDX amplifier incorporates
Alpine's new Power Management circuit. The Power Management Processor controls
all aspects of amplifier performance, monitoring voltage, temperature and output
to ensure uninterrupted power output for non-stop listening.
Uninterrupted Protection Circuits: If the amplifier gets too
hot, the Thermal Protection circuit kicks in and gradually decreases output
power until it cools down. Once cool, the power output automatically increases
back to the previous level. If the circuit detects a Low Battery condition, it
will gradually decrease power output if battery voltage becomes too low. Once
the battery voltage increases, power will be restored. This interruption-free
design allows for non-stop enjoyment with no hiccups or drop-outs, just clean,
Channel Design: The Alpine PDX-F4 can be configured as a
4-channel, 3-channel, or 2-channel amplifier. The amplifier is stable down to
2-ohms in stereo, and 4-ohms when bridged.
Low Impedance Stability: This amp is stable at low impedances and is
capable of its rated power (100-watts x 4-channel) from 2 to 4 ohms. This allows
excellent flexibility with multiple speaker and subwoofer loads and is adjusted
CEA 2006 Compliant: The PDX-F4's power ratings are measured
according to the strict standards dictated by the Consumer Electronics
Association (CEA). These standards allow you to accurately compare the rated
power output of all CEA 2006-compliant amplifiers, even if they come from
different brands. Manufacturers who adhere to the standards can display the CEA
2006 logo on their products and packaging.
- Four-Channel (4-ohm): 100 watts x
4-channel in 4-ohms @ 20 to 20,000 Hz with 1% THD+N
- Four-Channel (2-ohm): 100 watts x
4-channel in 2-ohms @ 20 to 20,000 Hz with 1% THD+N
- Bridged (4-ohm): 200 watts x 2-channel
in 4-ohms @ 20 to 20,000 Hz with 1%
Verification Certificate: The amplifier comes with a certificate
that lists the RMS power output of the individual amplifier. It also lists the model
number, serial number, test date, and the test conditions (14.4 volts, 4 ohms).
Ultra-Wide Frequency Response: The Alpine PDX-F4 offers a
super-wide, frequency range (5Hz-100kHz) for unparallel sound quality and detail.
Ultra-Low Output Impedance: With ultra-low output impedance, the
PDX-F4 offers extremely controlled, tight bass for unprecedented sound quality.
The amplifier's Damping Factor is rated at >500.
High Signal-to-Noise: This amplifier is capable of S/N ratios
up to 98dB S/N @ 1W, 118dB S/N at rated power for extremely clean, uncolored sound.
The PDX amp delivers crystal clear music every time, without unwanted background
noise or static.
Beefy Power Supply: The PDX amplifier's power supply delivers
tremendous headroom with low distortion and noise. The PDX amplifier has an
extremely high total system efficiency of ~80% (power supply is rated at >90%,
output stage is rated >90%).
Stackable: The PDX series amplifiers are 20% thinner than
previous models at only 2" thick. A newly designed stacking system packs the
amps closer together so there are no gaps and to save space in the trunk while
directly coupling the amps heatsinks to help share cooling duties.
Notes: When stacking multiple
amplifiers, do not install vertically or at an incline.
Any stack installation other than parallel to the vehicle
floor, invalidates the warranty.
LED: The top mounted LED Power indicator glows blue when the
amplifier is turned on.
Hidden Controls: The Alpine PDX amplifier's controls are
hidden behind a decorative front-panel. The front-panel is removed by unscrewing
one machine-screw with the supplied hex-key and then prying the front-panel open.
Gain control: The PDX-F4 provides independent rotary controls
for the front and rear channels to set the amplifier's gain according to the level
of the incoming signal. The gain settings is continuously variable from 0.2V to
Crossover Mode Switch: The Alpine PDX-F4 offers independent
crossovers for the front and rear channels. Each crossover can be set to HP (high
pass), OFF (full range) or LP (low-pass).
Crossover Frequency: You can independently select the crossover
frequency for the front and rear channel crossovers. The crossovers are variable from
30 to 400Hz (-12 dB/oct).
Terminal Layout: For wiring convenience, all of the inputs
and outputs on the amplifier are on one side.
Quick Connect Plugs: The PDX series amplifier uses quick
connect plugs to attach your system's speaker wires and power cables to the
amp for a simple, error-free installation.
Quick Connect Speaker Terminals: The Alpine PDX-F4 includes
four quick connect high-power speaker terminals. Bare speaker wire, up to 8 gauge,
is held in place by screw-clamps on the quick connectors. The four speaker terminal
quick connectors then plugs into the amplifier.
Quick Connect Battery Terminals: The removable battery terminal
quick connector features a low-loss, high-current design. It accepts up to 4GA wire
for power and ground, to ensure your amp gets the power it needs while allowing for
easy installation. The remote-turn on lead will accept up 12 gauge wire. The power,
ground, and remote-turn on lead are secured by set-screws on quick connector. The
battery terminal quick connector then plugs into the amplifier.
Line Level Input: The Alpine PDX-F4 is equipped with four
gold-plated female RCA jacks.
Fuses: The Alpine PDX-F4 is equipped with two 30-amp ATO