Skip Navigation

Rockford Fosgate Fanatic P Component Speaker Systems

FNP-1614 ( )

Item #: 575FNP1514

This item is no longer available.

Shop all Component Speakers

149.95

Overview

Our take on the Rockford Fosgate Fanatic P Component Speaker Systems

FNP-1514 — uses 5-1/4" woofers

Specs:
  • frequency response 60-20k Hz
  • power range 8-50 watts RMS
  • sensitivity 88.7 dB.

What's in the Box:

  • 2 woofers
  • 2 grilles w/ grille rings
  • 2 red and black self-adhesive grille logos
  • 2 tweeters
  • 2 crossovers w/ attached input/output leads
  • 2 flush mount housings
  • 2 flush mount brackets
  • 2 surface mount housings
  • 2 flush/surface mount trim rings
  • 2 flush/surface mount back plates
  • 2 wedge mount housings
  • 1- 20' length of speaker wire (no connectors)
  • 8- 1.25" sheet-metal screws
  • 8- 0.75" sheet-metal screws
  • 4- 0.5" hex-head bolts and nuts
  • 2- 0.110" male quick-slides w/ rubber insulators
  • 4- 0.110" female quick-slides w/ rubber insulators
  • 2- 0.187" female quick-slides w/ rubber insulators
  • Manual (English/Spanish/French/German/Italian) w/ warranty (English) and specs information (English)
  • Product registration card
Reviews
Details

Hands-on research

Features and Specs

General
Speaker Size 5 1/4
Design 2-way
Tweeter Design Dome
Tweeter Composition Mylar
Woofer Composition Mica-filled Poly
Woofer Surround Foam
Parts Warranty 1 YEAR
Labor Warranty 1 YEAR
Specifications
Sensitivity (1W at 1 meter) 88.7
Sensitivity at 2.83 volts N/A
Frequency Response 60 - 20k Hz
Minimum RMS Wattage 8
Maximum RMS Wattage 50
Peak Power Handling (Watts) N/A
Impedance (Ohms) 4
Top-mount Depth (Inches) 2 5/16
Bottom-mount Depth (Inches) 2 1/2
Cutout Diameter or Length (inches) 4 1/2

Product Research

Woofers
Tweeters
Special Features

Woofers

The woofer cones are mica filled polypropylene, a strong, lightweight material with high internal damping to provide excellent sound reproduction.

The spider has the job of centering the voice coil and providing the rear suspension for the speaker. The Fanatic P Component system woofers use a cupped spider to ensure great sound with long life and durability.

A 1" Voice Coil with an anodized aluminum former  for more efficient heat dissipation helps ensure durability and high power handling.

Tweeters

A synthetic fluid (Ferrofluid) is placed in the magnetic gap of the tweeter to aid in the cooling of the voice coil; this results in higher power handling and greater reliability.

Neodymium magnets are used to produce a strong magnetic field, so that a small magnet may be used to enable a tweeter to have very high performance.

The 3/4" dome tweeters come installed in the flush mount sockets. To remove the tweeter from the socket, turn the backplate of the socket counter clockwise, then lift the backplate away from the socket to access the tweeter.

Tweeter Mounting Options: The tweeters may be flush, surface or "wedge" mounted. The tweeters swivel inside the flush and surface mount sockets, but do not swivel in the "wedge mount" socket.  The "wedge mount" sockets surface mount to the vehicle and hold the tweeters at a fixed angle (may be mounted to provide a 15 or 60 degree angle). The tweeters must be installed using one of the three sockets.

  Flush Mount (swivel) Surface Mount (swivel) "Wedge Mount" (fixed 15 or 60 degree angle)
Mounting Depth 1.069" NA NA
Mounting Height 0.395" 1.065" 1.494"
Cutout Diameter 1.75" NA NA
Frame Diameter 1.928" 1.781" 1.563"

     
Special Features

Crossover Dimensions: 4.397"L x 1.687"W x 0.858"H

The crossovers contain an 18dB/octave, 6.3kHz high-pass network to prevent low frequencies from being sent to the tweeters; full range signals are sent to the woofers (extreme high and low frequencies are automatically rolled off by the woofer according to it's inherent high and low frequency limitations).

Optical Compression Tweeter Protection:This built-in protection circuit limits power to the tweeter when the "danger" threshold is exceeded. Because the circuit simply limits power and doesn't shut the tweeter off, this method of protection is inaudible.

The crossover input wires are bare ended, while the output wires are terminated with quick-slides.

There is one mounting tab on each end of the crossover.

Specifications Note: The manual lists separate sensitivity specs for the woofer (86.4dB) and tweeter (91dB). The sensitivity figure listed in the Crutchfield database is the average of the two individual sensitivity specifications. The average sensitivity (88.7dB) is given  because it more accurately represents the overall sensitivity of the system; this permits a better estimation of the power needed for clean, high volume output.

Our Product Research Team

At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.

Accessories
Library
;