Overview: The Rockford Fosgate Prime R250-4
4-channel amplifier is designed to power two pairs of full-range or component
speakers in 4-channel mode, two subwoofers in bridged 2-channel mode, or two
full-range speakers and a single subwoofer in 3-channel mode.
CEA 2006 Compliant: The Rockford Fosgate Prime R250-4's
power ratings are measured according to standards provided by the
Consumer Electronics Association (CEA). These standards allow you to accurately
compare the rated power output of all CEA 2006-compliant amplifiers, even if
they come from different brands. Manufacturers who adhere to the standards can
display the CEA 2006 logo on their products and packaging. CEA2006
Specifications for this amplifier are:
- Four-Channel: 40 watts RMS x 4 at 4 ohms, 14.4 V, and 1% THD+N (65 watts x
4 at 2 ohms, 14.4 V, and 1% THD+N)
- Two-Channel Bridged: 125 Watts x 2 at 4 ohms, 14.4 V, and 1% THD+N
LED Indicators: The Rockford Fosgate amplifier is equipped with two
side-mounted LED indicators.
- Power LED: illuminates blue when the unit is turned on.
- Protect LED: illuminates red if a short circuit or too
low of an impedance is detected at the speaker connections. The amplifier
will automatically shut down if this occurs.
Mounting: The amplifier can be mounted vertically or horizontally
using the supplied mounting screws. The amplifier should never be mounted in an engine compartment
as this will void the warranty.
Gain Controls: The R250-4 is equipped with independent gain
controls for the front and rear channels. The amplifier's gain controls are preset to match the
output of most source units. The gain controls can be adjusted from 1 to 11 with
an input sensitivity range of 150mV to 8V.
Crossovers: The amplifier is equipped with independent 12dB/octave
Butterworth crossovers for the front and rear channels. The Crossover Switches allows you
to select from the following:
- All-Pass (full-range): The all-pass setting allows all frequencies
(20-20kHz) to pass through the amplifier from your connected headunit to
- High-Pass: The high-pass setting is fixed and allows only
frequencies above 80Hz to pass through the amplifier to your speakers.
- Low-Pass: The low-pass setting is variable and allows only
frequencies below 50-250Hz to pass through the amplifier to your speakers.
Punch Bass: The Punch bass controls for the front and rear
channels can be set to 0dB, +6dB, +12dB at a fixed 45Hz.
Power Terminals: The power and ground terminals are nickel-plated
screw terminals and will accommodate up to 4 AWG power/ground wire (up to 1/2"
spade or ring-style connector).
Note: Based on the 40A fuse rating and the power output
of the amplifier, an 8-gauge amplifier wiring kit is recommended.
Remote Turn-On Terminal: The remote turn-on terminal is a
nickel-plated screw terminal that will accommodate up to an 8 AWG wire (up 3/8"
spade or ring-style connector). This terminal is used to remotely turn-on and
turn-off the amplifier when +12V DC is applied, when connected to your
head unit's remote turn-on lead.
Speaker Terminals: The eight speaker terminals (front left +/-,
rear left +/-, front right +/-, and rear right +/-)
are heavy duty, nickel-plated screw-terminals what will accommodate up to 8 AWG
speaker wire (up to 3/8" spade or ring-style connectors).
RCA Input Jacks: The industry standard RCA jacks provide an easy
connection for signal level input. They are nickel-plated to resist signal
degradation caused by corrosion. There are 4 RCA input jacks for front
left/right and rear left/right channels.
Fuses: The amplifier is equipped with two installed 20-amp ATC fuses.
The amplifier also comes supplied with two spare 20-amp fuses.
Our Product Research Team
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.