Why Choose Crutchfield?
Great gear and expert advice
Our experts help you pick the ideal gear for your needs.Meet our advisors
Free tech support for the life of your gear.Read about our one-on-one expert help
You may return items that are complete and like new for any reason within 60 days.See the details of our return policy
Earn one point for every dollar you spend and use those points to save on future purchases.Get full details on Crutchfield Rewards
Deep discounts on car installation gear
We offer vehicle-specific installation instructions, dash kits, wiring harnesses, and speaker accessories at deeply discounted prices with car stereo and speaker purchases. Available for most vehicles.Learn more
Trusted since 1974
Our customers have trusted us with their business, and they’ve helped us win awards for our service.Check out our most recent awards
The manufacturer’s warranty always applies.See more details
Wet Sounds HT-1
Mono marine subwoofer amplifier — 600 watts RMS x 1 at 2 ohms
Wet Sounds HT-1
Our take on the Wet Sounds HT-1 by Crutchfield's Jon Paulette
Built for boating
Designed by boaters for boaters, Wet Sounds built their Hydro-Tech™ amps for use in the often-harsh marine environment. A conformal-coated circuit board, a sealed, salt-water resistant heat sink, and stainless steel hardware ensure that your amp will stand up to salt, spray, high temperatures, and high volume levels for seasons to come.
Wet Sounds HT-1 marine subwoofer amplifier
A powerful sub amp
The Wet Sounds HT-1 amp packs a lot of punch into a compact package. This Class D mono sub amplifier can deliver up to 600 watts RMS to your marine subs, so you'll have plenty of low-end punch when you're out on the high seas. The amp's control panel includes a low-pass crossover, bass boost, and phase switch, so you can fine-tune your sub to make your music sound the way you want it to.
For added flexibility, the HT-1 includes a wired remote control knob that makes it easy to adjust your sub's volume level from the helm.
Get the look you like
Because every boat installation (not to mention every boater) is unique, these amps let you create a great-sounding system that suits your boat — and your style. If you want to show off your gear, you can paint the accent stripes and removable wiring and control covers to match your boat's color combination. You can also place the backlit logo badge horizontally or vertically.
What's in the Box:
- Marine mono subwoofer amplifier
- Power terminal block
- Speaker terminal block
- Wired remote level control with attached 16-1/4' Cable (terminated with a 3.5mm mini-jack)
- 4 Mounting feet
- 2 End covers (installed)
- Four 25-amp ATO blade fuses (2 installed/ 2 spare)
- Four 1-1/2" Self tapping screws
- Eight 1/4" Screws (to install the feet)
- Two 3/8" Screws (to mount wired remote)
- 2 Flat washers
- Wet Sounds logo badge
- 2 Adhesive backed accent stripes
- mono marine amplifier
- Class-D design
- 300 watts RMS x 1 at 4 ohms (600 watts RMS x 1 at 2 ohms)
- frequency response: 20-250 Hz
- variable low-pass filter, bass boost, and phase control
- rugged water-resistant shell
- preamp inputs and outputs
- remote bass control knob with 16-foot cable included
- fuse rating: two 25-amp fuses (four fuses included)
- 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- dimensions: 11-1/16"W x 7-5/16"D x 2-3/8"H
- warranty: 1 year
- Our 60-day money-back guarantee
Features and Specs
|RMS Power Output (Watts x Channels)||300 x 1|
|Frequency Response at Rated RMS Power||20-250 Hz|
|THD at Rated RMS Power||0.15%|
|Signal to Noise Ratio||95 dB|
|Peak Power Output (Watts x Channels)||N/A|
|Power at 2 Ohms (Watts x Channels)||600 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||2|
|Low-Pass Crossover Frequency||50-250 Hz|
|Low-Pass Slope (dB/octave)||24 dB/octave|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0-18 dB|
|Bass Boost Frequency||45 Hz|
|Speaker Level Inputs||No|
|Preamp Outputs||1 pair|
|Parts Warranty||2 Years|
|Labor Warranty||2 Years|
Marine Amplifier: The Wet Sounds Hydro-Tech series amplifiers, with conformal coated PCBs, are specifically designed for marine applications. However, the amps are not waterproof, and should not be mounted where they are likely to get wet.
Mounting Feet: Using the included mounting feet adds approximately 1/2" to the height of the amp, but allows you to hide the wiring under the chassis.
Logo: The Wet Sounds logo mounts over the status LED, on the top of the amp. It can be mounted vertically or horizontally.
End Covers: There are removable covers on both ends of the amp to help protect the controls and connections. The covers can be painted.
Note: A 3mm Allen wrench (not included) is needed to remove the covers. They must be removed during the installation.
Wired Remote: A wired remote level control is included. The remote has integrated flanges and screws are included to mount the unit under the dash. A 16-1/4' cable is attached to connect to the amplifier.
Note: The wired remote measures approximately 1-3/4" wide (2-1/2" including the mounting flanges) x 1" tall x 1-5/8" deep (2-1/4" including the knob and cable).
Control Panel Cover: All the controls are protected by a rubber cover to help keep them dry.
Gain: The input gain is a continuously variable rotary control; 200 mV to 5 V.
Crossover: The low pass crossover point is adjustable from 50 Hz to 250 Hz. Because the HT-1 is a subwoofer amp, the crossover is always engaged.
Phase: The output phase is switchable; 0° or 180°.
Bass Boost: The bass boost, centered at 45 Hz, is continuously variable from 0 dB (flat) to +18 dB.
Power Terminal Block: The amplifier has a power/ground terminal block that detaches from the amplifier, making it easier to connect the power and ground wires. Once the connections are made, the terminal block plugs into the amplifier. The power/ground block has set screw terminals and will accept 4 gauge wire.
Speaker Terminal Block: The speaker terminal block is also detachable from the amplifier. The speaker block has set screw terminals for two speakers (internally wired in parallel) and the remote turn-on lead; each will accept 12-16 gauge wire.
Preamp Inputs: The amplifier has one pair of RCA jack inputs.
Preamp Outputs: There is also one pair of pass-through preamp outputs, making it easy to connect another amplifier without running an extra set of RCA cables.
Remote Level Control: The included wired remote plugs into a 3.5mm mini-plug.
Note: The preamp inputs, preamp outputs, and wired remote input are extended 5" from the amp on pigtail wires.
Fuses: The amplifier is protected by two 25-amp ATO blade-type fuses.
Our Product Research Team
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.