Digital stereo multi-source power amplifier
Item # 021AD2002 | MFR # AD2002
$449.99 Earn up to 450 Rewards points
Offers & Financing
Our take on the AudioSource AD2002 by Crutchfield's Kramer Crane
A powerful amp with flexible options
When AudioSource brought in their new AD2002 power amplifier for us to listen to, I was really impressed. This compact workhorse is absolutely packed with features. It combines robust amplification with useful customization and control options — all while maintaining a small footprint. The versatile '2002 delivers high-quality playback for both analog sources like a tuner or turntable, and digital sources like a TV or CD player. I really like this amp for folks that want an easy two-zone music system. Use it to drive your favorite tower or bookshelf speakers in your living room, while also playing music through a pair of outdoor speakers at the same time.
Easily play music in two rooms
The AD2002 is a great amp for setting up a two-zone music system. It can drive two separate pairs of speakers connected to its A and B binding posts. Because it's four-ohm stable, you can enjoy music through two pairs of eight-ohm speakers simultaneously. Play music indoors through the A pair of speakers, and listen to the same source outside through the B speakers. When it's time to come inside for the night, simply switch off the B pair and let the party continue inside. The included remote provides easy control.
Lots of power under the hood
At its heart, the AD2002 is an old-school power amplifier with 100 watts of continuous power per channel when connected to a pair of eight-ohm speakers. It also cranks out 225 watts at four ohms. Want to bridge the channels and use it as a mono amp for a single speaker? You'll get a whopping 450 watts of clean power from this amp. Use multiple AD2002s for a cost- and space-efficient way to get separate amplification for each channel of your home theater or two-channel system.
Multiple source and power-on options
The AD2002 offers two pairs of analog RCA inputs for your music sources. It also offers an optical digital input, which provides a high-quality connection for a TV, CD player, or network music streamer. The amp can switch sources automatically when a signal is detected. It can be turned on manually, or automatically when it detects a source. It is also 12-volt trigger compatible so you can have it turn on when another piece of equipment is fired up. Rear-mounted bass and treble controls provide tone adjustment for your room.
Never worry about blowing your speakers
One of the features I like the most about the AD2002 is the ability to set maximum volume limits. On the upper left corner of the back panel are two small dials. These let you set a volume "ceiling" for each channel, so even if some over-enthusiastic listener maxes out the volume knob on the front of the amp, there won't be any damage to the speakers. This is a great way to make sure that guests or kids don't accidentally turn the system up to distortion levels.
- 100 watts x 2 into 8 ohms or 225 watts into 4 ohms
- 450 watts when bridged into a single 8-ohm load
- high-efficiency switching amplifier design
- front-panel volume and balance controls
- binding post A and B speaker connectors
- A/B speaker switching
- speaker-level input allows integration into an existing system where no RCA level signal is present
- optical digital input for connecting a TV, CD player, or network streaming device
- rear-panel bass and treble controls
- loop output on the main line input passes that audio signal on to another amp, giving you flexibility in designing a larger multi-room system
- main and secondary ("Interrupt") audio line inputs with automatic source switching
- signal sensing "Power On" and Trigger mode
- auto-on select switch allows manual or signal sensing power on/off
- master volume feature allows installer to set maximum volume so connected speakers cannot be distorted or damaged
- adjustable delay so that the amp doesn't switch to another source at the end of a song
- infrared remote control included
- rack-mountable with included hardware
- frequency response: 20-20,000 Hz
- signal-to-noise ratio: 100 dB
- warranty: 2 years
- Our 60-day money-back guarantee
What's in the Box:
- Digital stereo power amplifier
- 6' AC power cord
- Remote control (CR2025 3V battery installed)
- 2 Rack-mount brackets
- 6 Machine screws
- Owner's Manual
This was exactly what I needed to extend great sound to our outdoor speakers. Could not have been easier to set up.
Vincent F, Lewis Center, OH
AudioSource AD2002 Reviews
Average Customer Review(s):
Thanks for submitting your review
Features and Specs
|Number of Channels||2|
|Power Output per Channel (8 ohms)||100|
|Power Output per Channel (6 ohms)||---|
|Power Output per Channel (4 ohms)||225|
|Bridged Power per Channel||450 watts|
|Parts Warranty||2 Years|
|Labor Warranty||2 Years|
|Inputs & Outputs|
|Number of Inputs||2|
AudioSource AD Series: AudioSource AD series amplifiers are designed for home and commercial audio distribution systems where high quality sound, flexibility, and reliability are essential. The AD series offers exceptional value and many features that will make their installation and use easy and convenient.
Digital Stereo Power Amplifier: The AudioSource AD2002 digital stereo power amplifier is designed for dedicated stereo & distributed audio applications. It offers A & B speaker outputs. The amplifier can be configured for Stereo or Bridged output.
- Stereo (8-ohm): 100 watts x 2 channel, 10-30kHz, <0.2% THD+N
- Stereo (4-ohm): 225 watts x 2 channel, 10-30kHz, <0.2% THD+N
- Bridged Mono (8-ohm): 450 watts x 2 channel, 1kHz, <0.2% THD+N
Rear-Panel Connections: The AudioSource AD2002 digital stereo power amplifier is equipped with the following inputs & outputs
- Main Input/Output: The AD2002 Main Input consists of stereo RCA jacks and are used as the amplifier's primary audio inputs. The Main Output also consists of stereo RCA jacks and passthrough the AD2002's Main Input audio signal to another amplifier.
- Interrupting Line Input: The Interrupting Input consists of stereo RCA Jacks. This input can be used if a second source is desired and takes over when signal is present and has at least a 5mV level. When there is no signal, or a signal with less than 5mV level, the amp switches back to Main input after a brief delay.
- Optical Digital Input: The amplifier features an optical (toslink) digital input that will accept 2ch PCM audio signals (not compatible with Dolby Digital/DTS).
- Speaker A/B Terminals: The AudioSource AD2002 is fitted with binding-post terminals for A & B speaker connection for powering up to two pair of speakers. The minimum impedance for each speaker section is 4-ohm in Stereo mode and 8-ohm in Bridged mode. The binding post terminals will accept bare wire (up to 10AWG), pin-connectors, and banana plugs (single only).
- High-Level Inputs: The screw-down high-level inputs can be used to connect a source with speaker-level output instead of line-level outputs. Route this high-level input signal to either the amplifier's Interrupt Input or Main Input.
- Trigger In/Out: The 12V trigger input and output allow the AD2002 to be powered on by other electronics or to power on other electronics via a 3.5mm minijack cable. The trigger input can operate with voltages between 3 and 20VDC.
- Power Cord: The digital stereo power amplifier features a detachable 6' AC power cord terminated by a 3-prong connector.
Front-Panel Controls: The AudioSource AD2002 digital stereo power amplifier features the following front-panel controls.
- Power Switch: The front-panel Power Switch turns the AD2002 on or off. A red LED indicates connection to AC power while in standby mode and turns green indicating audio signal is present.
- Volume Trim: This rotary encoder adjust amplifier volume from -12dB to +6dB relative to the the Master Volume control the back panel.
- A/B Speaker Selector: You can select Speakers A, Speakers B, or Both for playback.
- Balance: The Balance control lets you fade the amplifier's speaker output between the Right & Left channels.
Rear-Panel Controls: The AudioSource AD2002 offers the following rear-panel controls.
- Master Volume: Provides independent volume level adjustment of the amplifier's left and right channels.
- Bass & Treble: Bass (100Hz) & Treble (10kHz) can be adjusted from -12dB to + 12dB.
- Mode Select (Stereo or Bridged): Select Stereo mode for connecting one or two pair of loudspeakers, When set to Bridged mode, the AD2002 becomes a single channel mono amplifier for powering one speaker. Only the Right audio input is used during bridged-mode. Only one zone (A or B) can be bridged; not both.
- Delay Time: Allows for a 3 to 15 second delay to be set when switching from the amplifier's Interrupting and Main Input.
- Power Mode: Set the Auto On switch to Normal for manual power on/off. Set the Auto switch to Auto for signal sensing; the amp will turn on when audio signal (>5mV) is detected at the inputs The front-panel power switch must be in the On position (pushed in) for the Auto On feature to operate. Or, select 12V Trigger which allows the AD2002 to be powered on by other electronic component or to power on other electronics via a 3.5 minijack cable (between 3-20VDC).
Remote Control: The AudioSource AD2002 includes an IR remote control for wireless operation of the amplifier. Remote control functions include Power/Standby, Volume Up/Down, Mute, and Speakers A/B.
Mounting Options: The AudioSource AD2002 digital stereo power amplifier features four rubber feet and can simply be placed on top of a flat surface; like a table-top, shelf, or stand. You can also remove the four rubber feet and rack-mount the amplifier using the included rack-mount ears and screws.
Our Product Research Team
At Crutchfield, you'll get detailed, accurate information that's hard to find elsewhere. That's because we have our own in-house Product Research team. They verify what’s in the box, check the owner's manual, and record dimensions, features and specs. We stay on top of new products and technologies to help people make informed choices.
Why did you buy this?
Sounds great [ scott Jun 15, 2018 ]
Recommended by Dallas. [ Lucius Mar 16, 2018 ]
Needed amp to replace old integrated amp used to drive 2 sets of speakers. Chose this due to being able to drive 2 pairs of speakers with a remote to choose A/B speakers and having enough power for my larger speakers. Well see how it sounds. [ Jeff Jan 06, 2018 ]
2 questions already asked
To be honest Russ, this would be a question better answered by the tech guys at Cruthchfield. I can tell you that the amp is a nice piece! [ Mike Jul 08, 2018 ]
Not sure. but it seems I saw it once in the downloaded PDF file of the owner's manual. [ Donald Jul 08, 2018 ]
Sorry, I have yet to install my amp so I can not answer your question. Sorry about that!! [ Mike May 23, 2017 ]
I can't say for sure, but I believe it does. I had to return mine, because I couldn't transfer digital audio to another room. However that problem had to do with the tuner-reciever's ability to transmit digital through the B-channel. Research your tuner-receiver's specs before you assume it will. I was surprised to learn my expensive Sony tuner did not transmit digital audio through to other room set-up.. [ GARRY May 20, 2017 ]
Looking for more? Check out the next model in this lineup.
Frequently Compared With
Digital stereo multi-source power amplifier
Stereo dual-source power amplifier
Digital stereo multi-source power amplifier
NAD C 275BEE
Stereo power amplifier