About the MB Quart PWE 304

Product highlights:
- 12" subwoofer with two 4-ohm voice coils
- treated paper cone with polypropylene dustcap and inverted Santoprene surround
- cast alloy basket
- power handling: 600 RMS watts (300 watts per voice coil)
- frequency range: 18-300 Hz
- sensitivity: 90 dB
- mounting depth: 6-1/4"
- sealed box volume: 1.0 cu. ft.
- Recommended Q-Logic Box Type: 1
- warranty: 3 years
- MFR # PWE 304
- Item # 049PWE304
What's in the box:
MB Quart PWE 304 owner's manual
If you need assistance accessing this owner's manual, please give us a call.- 12" Dual-voice coil subwoofer
- Plastic cover ring
- 3 Terminal jumpers (2 short/1 long)
- 4 Terminal set screws
- 2mm Allen wrench
- "MB Quart Premium" badge
- Self-adhesive foam gasket (in 4 pieces)
- Installation Manual
More details on the MB Quart PWE 304

Features & specs
Features and Specs | ||
---|---|---|
Size | 12-inch | |
Impedance (Ohms) | --- | |
Cone Material | TreatedPaper/Poly dustcap | |
Surround Material | Santoprene | |
Basket Material | --- | |
Grille | Not included | |
Free-Air | No | |
Dual Voice Coil | Yes | |
Sensitivity |
90 dB at 1 watt | |
Frequency Response | 18 - 300 Hz | |
Max RMS Power Handling | 600 | |
Peak Power Handling (Watts) | --- | |
Top Mount Depth (inches) | 6 1/4 | |
Bottom Mount Depth (inches) | --- | |
Cutout Diameter or Length (inches) | 11 1/16 | |
Frame Width | 12.4375 | |
Frame Length | 12.4375 | |
Vas (liters) | 28.4 | |
Fs (Hz) | 34 | |
Qts | 0.54 | |
Xmax (millimeters) | --- | |
Parts Warranty | 3 Years | |
Labor Warranty | 3 Years | |
Box Requirements | ||
Ideal Sealed Box Volume (cubic feet) | 1 | |
Minimum Sealed Box Volume (cubic feet) | 1 | |
Maximum Sealed Box Volume (cubic feet) | 1 | |
Ideal Ported Box Volume (cubic feet) | N/A | |
Minimum Ported Box Volume (cubic feet) | N/A | |
Maximum Ported Box Volume (cubic feet) | N/A | |
Port diameter (inches) | N/A | |
Port length (inches) | N/A |
Product Research
Woofer Construction: This MB Quart Premium Series woofer is equipped with a treated paper diaphragm with an inverted parabolic polypropylene dust cap and a Santoprene synthetic rubber, inverted roll surround.
Basket: The PWE 304's motor structure is supported by a high-strength, non-resonant cast alloy basket.
Kapton Voice Coil Former: Kapton is a highly temperature-resistant, completely non-magnetic plastic foil. Because it has no affect on the magnetic field, the woofer provides more precise, distortion-free music reproduction.
Speaker Terminals: This dual-voice-coil subwoofer has a unique speaker terminal which can accept up to 10-gauge wire. The one-piece terminal block holds the speaker wire in place using set screws (2mm Allen wrench supplied). A plastic cover protects the terminal strip from unwanted contact.
Wiring: The woofer can be connected in the following ways:
- Standard: You can connect the woofer to two separate amplifier channels, and each channel will see a 4-ohm load. Connections are made to the woofer's +1, +2, -1, and -2 terminals.
- Parallel: You can connect the woofer to a single amplifier channel which will see a 2-ohm load. Connections are made to the woofer's +1, and -2 terminals. Two supplied short terminal jumpers are attached to the terminal block to link together the two positive terminals and the two negative terminals.
- Series: You can connect the woofer to a single amplifier channel which will see an 8-ohm load. Connections are made to the woofer's +1, and -2 terminals. The supplied long terminal jumper is attached to the terminal block to link together the +2 and -1 terminals.
Logo Badge: The self-adhesive MB Quart Premium Logo badge can be mounted on the top of the screw cover ring in either direction.
Enclosure Recommendation: MB Quart recommends a sealed enclosure with an internal volume of 1.0 cu.ft. for this woofer.
Mounting Recommendations: The PWE 304 can only be top-mounted into the enclosure. The supplied self-adhesive rubber gasket should be placed on the woofer to ensure a tight seal. No mounting hardware is included, however, MB Quart recommends M5 hex-head screws and lock nuts. After installation, the supplied screw cover ring can be fitted to the woofer's outer ring for a custom look.
Miscellaneous Specs:
- Power Handling: 600 watts RMS (300 watts per voice coil)
- Mounting Height: 0.224" without cover ring, 0.522" with ring installed
Loading...
Loading accessories...
Customer Q&A
Loading...
Loading articles...
These are hard core they bump i would recommend to anyone if you want hard hitting bass sound these are it Aloha!!!!
kenneth from Honolulu HI