About the Polk Audio MM 6502
Product highlights:
- component speaker system includes 2 woofers, 2 tweeters, 2 external crossover networks, and mounting gear
- 6-1/2" titanium coated polymer woofer cone with Santoprene rubber surround
- 1" Terylene fabric dome tweeter
- certified for marine use (IP56 rating)
- non-corrosive fiberglass reinforced ABS basket
- epoxy coated crossovers
- waterproof surrounds
- weep holes for proper drainage
- handles up to 125 watts RMS (375 watts peak power)
- frequency response: 35-40,000 Hz
- sensitivity: 93 dB
- impedance: 4 ohms
- cutout dimensions (woofer): 5"
- top-mount depth (woofer): 2-5/8"
- grilles included
- warranty: 1 year
- MFR # AA8650-A
- Item # 107MM6502
What's in the box:
Polk Audio MM 6502 owner's manual
If you need assistance accessing this owner's manual, please give us a call.- 2 Woofers
- 2 Woofer grilles
- 2 Mounting brackets
- 2 Foam woofer gaskets
- 2 Tweeters (each has 6" speaker leads attached)
- 2 Flush-mount cups
- 2 Metal flush-mount clamps
- 2 Surface-mount cups
- 2 Crossovers
- Two 39" Woofer wires (each has female quick-slides on one end and tinned wire on the other)
- Two 39" Tweeter wires (each has female quick-slides on one end and tinned wire on the other)
- Two 38" Crossover input wires (each is tinned on both ends)
- Eight 1" Stainless steel screws
- Four 1-1/8" Stainless steel screws
- Two 5/8" Stainless steel screws
- Two M4x13mm Stainless steel machine screws
- 8 Stainless steel speed clips
- 2 Factory grille badges
- Installation / Specification sheet
- Online product registration information
More details on the Polk Audio MM 6502
Features & specs
| General | ||
|---|---|---|
| Speaker Size | 6 1/2 | |
| Driver Design | 2-way | |
| Woofer Design | Cone | |
| Woofer Material | Titanium Coated Composite | |
| Woofer Surround | Santoprene Rubber | |
| Midrange Design | --- | |
| Midrange Material | --- | |
| Tweeter Design | 1" Dome | |
| Tweeter Material | Terylene Fabric | |
| Super Tweeter Design | --- | |
| Super Tweeter Material | --- | |
| Impedance (Ohms) | 4 | |
| Weather-resistant | Yes | |
| Grilles Included | Black aluminum mesh, Black and gray plastic frame | |
| Parts Warranty | 1 Year | |
| Labor Warranty | 1 Year | |
| Specifications | ||
| Sensitivity (1W at 1 meter) | 93 | |
| Sensitivity at 2.83 volts | N/A | |
| Frequency Response | 35 - 40k Hz | |
| Maximum RMS Wattage | 125 | |
| Peak Power Handling (Watts) | 375 | |
| Top-mount Depth (Inches) | 2 5/8 | |
| Bottom-mount Depth (Inches) | 2 15/16 | |
| Cutout Diameter or Length (inches) | 5 1/16 | |
| Mounting Height (Inches) | 0.437 | |
| Frame Width | 6.485 | |
| Frame Length | 6.485 | |
Product Research
Woofers
Ultra-Marine Certified: Polk MM1 Series speakers are tested to withstand exposure to salt-fog, UV rays, and humidity, so they'll work well in boats and cars. They also include stainless mounting hardware for corrosion resistance.
Size Classification Note: These speakers are marketed as 6½"; the woofers will fit in standard 6½" speaker openings, but do not use the standard 6½" speaker bolt pattern. In order to install them in standard 6½" speaker openings you must drill new screw holes. If new holes are drilled in the mounting surface of the car, no bracket is needed. If drilling in the car is not an option, the included brackets can be used, which have standard 6½" mounting holes, the Ford non-symmetric four hole pattern, and non-standard 6¾" three and four hole patterns. Enter your vehicle information to confirm fit.
Note: The opening for a standard 6½" speaker is not a 6½" diameter hole. (It's approximately 5" in diameter.)
Dynamic Balance: Dynamic Balance is a proprietary Polk Audio technology using laser imaging to determine what combination of speaker materials create the least resonance. Eliminating resonance in speakers results in a wide, smooth response and low distortion.
Neodymium Magnets: The woofers' neodymium magnets offer an exceptional strength to weight ratio, and are much smaller than typical magnets of equal strength.
Woofer Basket: The woofer baskets are fiberglass reinforced ABS, lightweight and corrosion resistant.
Drainage: The woofer should be mounted so the slots along the perimeter of one side of the basket are at the bottom, so any trapped water can drain.
Tweeters
Material: The tweeter material is Terylene, a brand name of polyethylene terephthalate (PET).
Mounting: The supplied mounting cups allow you to surface-mount or flush-mount the tweeters. The tweeters swivel in both housings, allowing you to adjust them for optimum imaging.
Tweeter Mounting Dimensions:
| Surface Mount | Flush Mount | |
|---|---|---|
| Mounting Height | 1.035" | 0.475" |
| Depth | 0.915" (screw depth) | 1.052" |
| Frame Diameter | 2.096" | 2.294" |
| Cutout Diameter | N/A | 1.940" |
Crossovers
2-Way Crossovers: Each outboard crossover features a 12dB/octave high-pass network for the tweeter and a 12dB/octave low-pass network for the woofer. The crossover point is 3.0 kHz.
Tweeter Attenuation Switch: You can adjust the output of the tweeter to match a level appropriate to your vehicle or your system. The tweeter attenuation switch can be set to -3dB, 0dB, or +3dB.
Connections: Each crossover has screw terminal inputs and outputs that will accommodate bare wire or spade connectors up to 0.375" wide.
Mounting: There are two screw holes in the base of each crossover for mounting.
Crossover Dimensions:
- Width: 3.571"
- Depth: 4.258"
- Height: 1.187"
The Polk Audio MM 6502 replaces these items:
- woven honeycomb glass fiber composite woofer
- 1" silk composite dome tweeter
- certified for marine use
Loading...
Loading accessories...
Customer Q&A
16 questions already asked
Loading...
Loading articles...
These things are amazing. They fit my Buick nicely, with the tweeters in the door sail panel. They are being powered by just 58WPC right now, though that will change. They absolutely sing, and the sound stage from these is superb. Best speakers I've ever had in a car!
JOSEPH from COLUMBUS, IN