Your cart
Chat
Contact us
Close contact box
Connect ID #
965 904 073 4
Connect ID #
965 904 073 4
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

MTX JackHammer JH5001

Mono subwoofer amplifier — 550 watts RMS x 1 at 1 ohm

Item # 236JH5001

Nothing's louder than a jack hammer, right? MTX proves that with their JackHammer Series JH5001 mono subwoofer amp,...

Find what Fits your vehicle

Nothing's louder than a jack hammer, right? MTX proves that with their JackHammer Series JH5001 mono subwoofer amp,...

California customers:
Please click here for your Proposition 65 warning.

Low stock
$329.95

Free lifetime tech support

Whenever you need a hand.

60-day price protection

We’ll reimburse you if the price drops.

Car-specific installation packages

Deep discounts on the essential accessories that help your new gear work with your car.

About the MTX JackHammer JH5001

Buck Pomerantz

LOUD

Nothing's louder than a jack hammer, right? MTX proves that with their JackHammer Series JH5001 mono subwoofer amp, which can put out up to 550 watts RMS. The amp can handle loads as low as one ohm, so it'll work well in a variety of multiple-sub setups. Speaker-level inputs let you integrate the amp into a system with a factory radio.

LOUD

Nothing's louder than a jack hammer, right? MTX proves that with their JackHammer Series JH5001 mono subwoofer amp, which can put out up to 550 watts RMS. The amp can handle loads as low as one ohm, so it'll work well in a variety of multiple-sub setups. Speaker-level inputs let you integrate the amp into a system with a factory radio.

Controls on top

All the tuning controls are located on the amp's top panel, so you'll have easy access to them after installation. Low-pass and subsonic filters optimize the sound to fit your particular sub and enclosure. You can add extra punch with a bass boost. A wired remote control lets you run your JackHammer from the front seat.

MTX JH5001

MTX JH5001 input panel

READ LESS

Product highlights:

  • mono subwoofer amplifier
    • 225 watts RMS x 1 at 4 ohms
    • 375 watts RMS x 1 at 2 ohms
    • 550 watts RMS x 1 at 1 ohm
  • Class D amp technology (frequency response: 20-250 Hz)
  • variable low-pass filter (40-250 Hz, 12 dB/octave)
  • variable subsonic filter (20-50 Hz, 12 dB/octave)
  • variable bass boost (0-12 dB at 45 Hz)
More Info:
  • wired remote level control included
  • preamp and speaker-level inputs
  • wiring, fuse, and hardware not included with amplifier
    • 4-gauge power and ground leads and a 60-amp fuse recommended
  • dimensions: 9-1/2"W x 2-5/8"H x 7-11/16"D
  • warranty: 2 years
  • Our 60-day money-back guarantee
  • MFR # JH5001

What's in the box:

  • Mono subwoofer amplifier
  • External Bass Control (wired remote)
  • 16.5' Wired remote cable (with RJ-25 connectors on one end and 3.5mm mini plug on the other)
  • Four 5/8" Screws
  • Two 1/2" Flat head screws
  • 2mm Allen wrench
  • 4mm Allen wrench
  • Owner's manual (English/ Spanish/ Italian/ French)

Customer reviews

Loading reviews...

MTX JackHammer JH5001 reviews

Average review:

5 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Customer provided image, click to load a larger version.
Customer provided image, click to load a larger version.

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee review (What's this?)

Reviewed on Samsung.com

This review was collected as part of a promotion

Pros:

Cons:

Crutchfield response
Customer provided image, click to load a larger version.

<< >>

More details on the MTX JackHammer JH5001

Mark G.

Product Research

Features

CTA-2006 Compliant: CTA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output. The criteria for measuring amplifier power uses a DC input voltage of 14.4 volts and the RMS power output is measured over a frequency range of 20 Hz to 20 kHz (for full range amplifiers), with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CTA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples).

CTA-2006 Specifications:

  • Power Output: 200 watts RMS x 1 into 4Ω (20-165 Hz)
  • Signal to Noise Ratio: 72 dBA (measured at 1 watt into 4Ω)

Other Specifications:

  • Power Output:
    • 2Ω: 375 watts RMS x 1 (≤1.0% THD+N)
    • 1Ω: 550 watts RMS x 1 (≤1.0% THD+N)

Controls:

  • Turn On: 2-position switch; select Remote (wired) or Audio (signal sensing)
  • Input Level: 2-position switch; select preamp-level or speaker-level
  • Gain: rotary control; variable from 135mV to 10V
  • Crossovers:
    • LPF: rotary frequency control; variable from 40 Hz to 250 Hz; the low pass filter is always engaged (it cannot be bypassed)
    • Sub Sonic: rotary frequency control; variable from 20 Hz to 50 Hz; used to remove extremely low frequencies that can't be cleanly reproduced by the subwoofer
  • Bass Boost: increase the bass level between 0dB and +12dB via the rotary control; centered at 45 Hz

Wire Connections: The JH5001 has set screw terminals for power, ground, turn-on (REM), and speaker outputs. The power and ground terminals will accept up to 4-gauge wire, and the turn-on and speaker outputs will accept up to 10-gauge wire. The set screws are loosened/tightened with one of the supplied Allen wrenches, 2mm or 4mm. There are two pair of speaker terminals, internally wired in parallel, so you can easily wire two subwoofers in parallel.

External Fuse: The amplifier does not include a built-in fuse, therefore an external fuse should be placed on the power wire, within 18" of the battery. It is recommended that an 8-gauge amplifier wiring kit and a 60-amp external fuse be used when installing the amplifier.

Input Signal: The amp's RCA inputs accept line-level and speaker-level inputs. When using a speaker-level input signal, an optional speaker wire to RCA adapter is recommended.

Wired Remote: The included external bass control (EBC) wired remote gives you control of the subwoofer output level within reach of the driver's seat.

EBC Dimensions:

  • Width: 2" (2.9" including the mounting tabs)
  • Height: 0.95"
  • Depth: 1.67" (2.42" including knob and wiring)

Loading accessories...

Customer Q&A

2 questions already asked

Q
My amp lights started blinking and the sub stopped what does this mean?
[ cooper  Dec 28, 2020 ]
1 answer
A
If you purchased the product from Crutchfield, feel free to contact our Tech Support team. They can walk you through the settings on the product and see if there may be a fix. Our toll-free Tech Support number is printed on your invoice, and is also available under the "My Orders" tab in the "My Account" section of our website. If you did not purchase the unit from Crutchfield, then you may want to contact the manufacturer.
[ KRISTINA  Jan 08, 2021 ]  Staff
Q
Can this amplifier be bridged?
[ DAVID  May 20, 2020 ]
1 answer
A
This is a class d subwoofer amp. It cannot be bridged, it is a mono block amp. 500 watts @ 2 ohms.
[ charles  May 20, 2020 ]

Loading articles...

TOP
Compare the sound