About the Crux SWRHN-62L Wiring Interface
Product highlights:
- connect a new stereo in select 2008-14 Honda vehicles
- retain your steering wheel audio controls with select car stereos by Alpine, Boss, Blaupunkt, Clarion, Dual, Jensen, JVC, Kenwood, Pioneer, Sony or Soundstream
- includes adapter for power antenna
- warranty: 1 year
- MFR # SWRHN-62L
- Item # 249HN62L
- California customers: Please click here for your Proposition 65 WARNING.
What's in the box:
Crux SWRHN-62L Wiring Interface owner's manual
If you need assistance accessing this owner's manual, please give us a call.- Radio replacement interface module
- Wiring harness
- Antenna adapter
- SWC harness
- Installation Instructions
More details on the Crux SWRHN-62L Wiring Interface

Product Research
Features
Honda Radio Replacement Interface: The CRUX SWRHN-62L is a radio replacement interface for select 2008-2013 Honda vehicles. It facilitates the integration of an aftermarket radio to enable retention of factory features when replacing a factory installed radio in select Honda vehicles. This interface is also pre-programmed for retention of steering wheel controls.
Compatibility: The CRUX SWRHN-62L is supported by the following 2008-2013 Honda vehicles; with non-amplified and non-navigation factory systems only.
Make | Model | Year |
---|---|---|
Honda | Accord (DX/EX/LX)* | 2008-2012 |
CRZ | 2011-2013 | |
Fit | 2009-2013 | |
Odyssey | 2008-2011 | |
Pilot* | 2009-2011 | |
Ridgeline | 2009-2013 |
Steering Wheel Control Retention: The CRUX SWRHN-62L also features a steering wheel control output for Pioneer, Sony, Alpine, Clarion, Kenwood, JVC, Jensen, Dual/Axxera, Boss and other aftermarket head units. The steering wheel control output consists of a right-angle 3.5mm connector and a light blue/yellow wire (use the connection that your aftermarket head unit is fitted with). You will also need to set the SWRHN-62L's dip-switches to the appropriate settings for your brand of aftermarket radio (see installation instructions).
Wiring Harness: The SWRHN-62L includes a wiring harness with a single 24-pin molex connector that plugs into your vehicle's factory radio harness. the SWRHN-62L interface module. On the other end of the harness is a 12-pin connector that plugs into the interface module. The wiring harness also provides bare-wire leads (power/ground, speaker, illumination, antenna, and vss) which will need to be hardwired to your aftermarket head unit's wiring harness. In addition, there is an antenna adapter to allow your aftermarket head unit to connect with the vehicle's factory AM/FM antenna.
Wire Color | Function |
---|---|
Black | Chassis Ground |
Red | +12 Volt Accessory |
Yellow | +12 Volt Constant |
Orange | Illumination |
Orange/white | Not Used |
Blue | Power Antenna |
Blue/white | Not Used |
White | Left Front Speaker + |
White/black | Left Front Speaker - |
Gray | Right Front Speaker + |
Gray/black | Right Front Speaker - |
Green | Left Rear Speaker + |
Green/black | Left Rear Speaker - |
Purple | Right Rear Speaker + |
Purple/black | Right Rear Speaker - |
Brown | Not Used |
Red/white | VSS |
Blue/yellow | Kenwood/JVC SWC |
Loading...
Loading accessories...
Customer Q&A
2 questions already asked
Loading...
Loading articles...
Worked great after using the UPDATED instructions. For HONDA it should be OFF | ON | ON |OFF There is an updated PDF on the manufacturer's website. I have attached a picture with the correct settings. I am using it with a Kenwood Head Unit.
Jack from Montclair, NJ