About the Crux SWRTY-61N Wiring Interface
Keep those factory options
You'll only be able to retain your steering wheel audio controls with a compatible car stereo made by Alpine, Blaupunkt, Clarion, JVC, Kenwood, Pioneer, or Sony. No other brands are currently compatible. Check the Details tab to see if steering wheel audio controls are retained in your vehicle.
Keep those factory options
Crux's SWRTY-61N interface ensures that you can keep the factory steering wheel controls in your Toyota when installing an aftermarket radio. With compatible receivers, you can also keep your Toyota's backup camera and auxiliary input. Connect this interface to the wires on your new stereo's wiring harness, and you've covered the power, ground, and factory speaker connections for your new stereo.
The SWRTY-61N interface also offers the reverse, illumination, and Vehicle Speed Sensor (V.S.S.) outputs that you'll need if you're installing a navigation receiver.
Note: The interface does not support the factory JBL amplifier.
Highlights:
- connect a new stereo in select 2011-up Toyota models
- retain your steering wheel controls with select car stereos
- retains your Toyota's rear-view camera and aux input with compatible receivers
- provides connections for Vehicle Speed Sensor (V.S.S.), reverse gear, and illumination for installing navigation receivers
- warranty: 1 year
- MFR # SWRTY-61N
What's in the box:
Crux SWRTY-61N Wiring Interface owner's manual
- Radio replacement interface module (w/ attached T- harness)
- Rear speaker harness
- SWC harness
- Parking brake harness
- Antenna adapter
- USB retention adapter (USB-TY01)
- Installation Instructions
Customer reviews for Crux SWRTY-61N Wiring Interface
Loading...
Loading reviews...
Average review:
4.5 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Crux SWRTY-61N Wiring Interface
Product Research
Features
Radio Replacement Interface for Toyota: The CRUX SWRTY-61N is a radio replacement interface for select 2012-up Toyota vehicles. It facilitates the integration of select aftermarket radios to enable retention of certain factory features when replacing a factory-installed radio. This enhanced interface retains the factory rear-view (backup) camera, USB port, and aux input, plus is pre-programmed for retention of steering wheel controls. It also includes navigation outputs.
Vehicle Compatibility: The CRUX SWRTY-61N is supported by the following Toyota vehicles; with non-amplified factory audio systems (as of 9/17/2019).
Make | Model | Year |
---|---|---|
Scion | FRS | 2012-2016 |
iM | 2016 | |
tC | 2012-2016 | |
xB | 2012-2015 | |
xD | 2012 | |
Toyota | 4-Runner | 2012-2019 |
Avalon | 2012-2018 | |
Camry | 2012-2017 | |
Corolla | 2012-2017 | |
Highlander | 2013-2018 | |
RAV4 | 2012-2018 | |
Sequoia | 2012-2018 | |
Tacoma | 2013-2019 | |
Tundra | 2013-2019 | |
Venza | 2012-2015 |
Supported Aftermarket Head Units: The CRUX SWRTY-61N radio replacement interface will only retain steering wheel audio controls with car stereos made by Pioneer, Sony, Alpine, Clarion, Kenwood, JVC, Jensen, Dual/Axxera, and Boss.
Steering Wheel Control Compatible: The CRUX SWRTY-61N features a steering wheel control output for compatible aftermarket head units. The steering wheel control output consists of a right-angle 3.5mm connector and a light blue/yellow wire (use the connection that your aftermarket head unit is fitted with). The SWRTY-61N interface module will work with any of the listed aftermarket head units, by setting its dip-switches (see owner's manual for appropriate setting).
Retains Backup Camera: This radio replacement interface also retains your vehicle's factory back-up camera; the included harness contains a male composite video connector that plugs into the female composite video camera input on the back of your aftermarket head unit.
Retains USB Port: The included USB-TY01 USB Retention Adapter allows you to retain the factory USB port. This port is handy for connecting your USB devices and keeping your phone charged. This USB adapter harness will work with Apple CarPlay or Android Auto, except if your vehicle has multiple USB ports or if your new aftermarket radio doesn't have a high-amperage charging port (1.5A and greater).
Auxiliary Input Retention: You also get to keep your vehicle's factory auxiliary (3.5mm) input. The included harness contains male stereo RCA connectors which plug into your aftermarket head unit's rear-panel Aux input. If your aftermarket head unit contains a 3.5mm Aux input, then you will need a female stereo RCA to male stereo minijack adapter cable (sold separately).
Navigation Outputs: The CRUX SWRTY-61N radio replacement interface module provides a VSS (vehicle speed sense), Parking Brake, and a Reverse Gear output to make installing an aftermarket Navigation radio simpler and less time consuming.
Loading...
Loading accessories...
Customer Q&A
21 questions already asked
Loading...
Loading articles...
The wiring harness to make OEM steering wheel and backup camera worked as planned without splicing. 2013 Camry, replacing with BOSS system, saved significant time during installation. Only issue was excess factory connectors which weren't needed. Called support who resolved questions.
Anthony from Colorado Spgs, CO