About the Kanto RV250G
An all-weather mount for on-the-go viewing
An all-weather mount for on-the-go viewing
Want a TV mount for your RV or boat? The rugged Kanto RV250G was designed for outdoor TVs. It's completely weatherproof, with stainless steel hardware and galvanized steel construction sealed in a powder-coated finish. Rear-mounted rubber bumpers give your mounted TV additional protection.
The RV250G features a quick-release latch so you can easily remove your TV. And the mount comes with two wall brackets for use in two locations. You can use your TV at home, and move it to your RV or boat whenever you like.
The mount can hold your TV as close as 2-5/8" from the wall, or out as far as 12-3/4". You can swivel your mounted TV 60° in either direction (depending on screen size), and tilt it up or down to avoid glare.
Velcro® straps secure cables and cords to the mount's arms. The RV250G can support TVs with screen sizes between 26" and 42" and weighing up to 40 lbs.
- designed for TVs 26"-42"
- supports up to 40 lbs.
- specially designed for RVs and boats
- weatherproof, galvanized steel construction with powder-coated finish construction and stainless steel hardware
- holds your TV as close as 2-5/8" from wall, or as far away as 12-3/4"
- swivel range: ±60° (depending on screen size)
- tilt range: -12° to +1°
- detachable straps secure cables and cords to arms
- screw-on wall plate covers
- adjustable rear-mounted rubber bumpers for added protection
- quick-release latch
- includes 2 wall plates for 2 different locations
- stud mounting required
- mounting hardware included
- 10-1/2"W x 10-3/4"H x 2-5/8"-12-3/4"D
- weight: 9.7 lbs.
- warranty: 5 years
- MFR # RV250G
What's in the box:
- Articulating arm assembly
- 2 Wall-mount brackets
- Small TV bracket
- Large TV bracket
- Four M4x16mm bolts
- Four M4x25mm bolts
- Four M5x16mm bolts
- Four M5x25mm bolts
- Four M6x16mm bolts
- Four M6x25mm bolts
- Four M8x20mm bolts
- Four M8x35m bolts
- Four M8x50mm bolts
- Four 5mm spacers
- Four 10mm spacers
- Four 14mm spacers
- Four M4/M5/M6 washers
- Four M8 washers
- Four M6x25mm screws
- Four M8x50mm lag-bolts
- 4 Concrete anchors
- 3 Cable-management straps
Customer reviews for Kanto RV250G
Average review:5.0 out of 5 stars
Thanks for submitting your review
More details on the Kanto RV250G
Features & specs
|Mount Type||Wall Mount|
|Roll (Level) Adjustment||No|
|Wood Stud (Single)||Yes|
|Wood Stud (Dual, 16-inch)||No|
|Wood Stud (Dual, 24-inch)||No|
TV Compatibility: The Kanto RV250G indoor/outdoor wall-mount bracket supports 26" to 42" flat-panel TVs that weigh up to 40 lbs. The TV must meet the following VESA and screw size requirements.
- VESA Sizes: 50x50, 75x75, 100x100, 100x150, 100x200, 150x100, 150x150, 200x100, 200x150, or 200x200
- Screw Size: M4, M5, M6, or M8
Note: Additional hardware may be required for your specific model of TV. For example; shorter or longer screws, thicker or slimmer washers or spacers. These additional accessories can often be found at your local hardware store.
Indoor & Outdoor Use: Specially designed for RVs and boats, this full-motion mounting bracket features an easy-lock mechanism and adjustable rubber bumpers to prevent your TV from moving during transit. Galvanized and stainless steel parts are used to inhibit rust, while a durable powder coated finish protects against wear and tear.
Dual Wall Plates: Along with a detachable arm assembly, the RV250G includes a secondary wall plate, giving you the freedom to easily transfer your TV between your home and vehicle. Easily slide the extension arm off one wall plate and attach it to the other.
Articulating Arm: Providing 12.7" of extension, the articulating arm allows you to tilt (12°), pan, and swivel (60°) your TV for optimal viewing. Fully retracted, the RV250G bracket places your TV only 2.6" from the wall.
Cable Management: Velcro cable management straps and screw-on wall plate covers are included to ensure a clean and organized setup.
Single Stud Installation: The Kanto RV250G indoor/outdoor TV wall-mount bracket mounts to a single wood stud. Mounting hardware is included for wood stud, brick, and concrete installations. Tools required for installation include -
- 7/32" bit (wood), 3/8" bit (masonry)
- Socket wrench
- Nut driver
- Phillips screwdriver
- Stud finder
1 question already asked