About the Alpine R2-W8D2

Product highlights:
- Featured in our article: Best 8" car subwoofers for 2025
- 8" subwoofer with dual 2-ohm voice coils
- Kevlar reinforced pulp cone with HAMR Santoprene rubber surround
- frequency response: 30-200 Hz
- power handling: 150-350 watts RMS (175 watts per coil)
- peak power: 1,000 watts
- sensitivity: 83.6 dB
- top-mount depth: 4.631"
- mounting height: 0.875"
- sealed box volume: 0.3-0.5 cu. ft.
- ported box volume: 0.3-0.75 cu. ft.
- grille not included
- warranty: 1 year
- MFR # R2-W8D2
- Item # 500R2W8D2
- California customers: Please click here for your Proposition 65 WARNING.
What's in the box:
- One 8" Dual 2-ohm voice coil subwoofer
- Plastic trim ring
- Two 4.5" jumper wires (each wire has a single banana connector on both ends)
- Application guide (English/ French)
- On-line product registration information
- Warranty information (English/ French)
- Important Notice (English /French)
Featured video:
More details on the Alpine R2-W8D2

Features & specs
Features and Specs | ||
---|---|---|
Size | 8-inch | |
Impedance (Ohms) | 1, 4 | |
Cone Material | Kevlar Reinforced Paper | |
Surround Material | Santoprene Rubber | |
Basket Material | Aluminum | |
Grille | None included | |
Free-Air | No | |
Dual Voice Coil | Yes | |
Sensitivity |
83.6 dB at 1 watt | |
Frequency Response | 30 - 200 Hz | |
Max RMS Power Handling | 350 | |
Peak Power Handling (Watts) | 1000 | |
Top Mount Depth (inches) | 4 11/16 | |
Bottom Mount Depth (inches) | N/A | |
Cutout Diameter or Length (inches) | 6 15/16 | |
Frame Width | 8.288 | |
Frame Length | 8.288 | |
Vas (liters) | 10.1 | |
Fs (Hz) | 42 | |
Qts | 0.48 | |
Xmax (millimeters) | 12 | |
Parts Warranty | 1 Year | |
Labor Warranty | 1 Year | |
Box Requirements | ||
Ideal Sealed Box Volume (cubic feet) | 0.3 | |
Minimum Sealed Box Volume (cubic feet) | 0.2 | |
Maximum Sealed Box Volume (cubic feet) | 0.5 | |
Ideal Ported Box Volume (cubic feet) | 0.73 | |
Minimum Ported Box Volume (cubic feet) | 0.3 | |
Maximum Ported Box Volume (cubic feet) | 0.75 | |
Port diameter (inches) | N/A | |
Port length (inches) | N/A |
Product Research
Features
Enclosure Compatibility
Features
Kevlar Reinforced Pulp Cone: This Alpine R-Series subwoofer has a two-piece structural parabolic Kevlar reinforced pulp cone. Kevlar adds strength and tear resistance to the woofer cone while maintaining the benefits of a pulp cone design. There is also an oversized inverted polypropylene/ceramic composite dust cap, which increases rigidity and reduces cone distortion at extreme volume levels.
HAMRS: The woofer features a High Amplitude Multi Roll Surround (HAMRS), made of Santoprene Rubber, that allows a large linear excursion and greater SPL. The HAMRS design allows extreme excursions without sacrificing valuable cone area.
Progressive Spider: The progressive spider has reinforced layer tinsel leads to ensure reliable and consistent control of the tinsel leads and eliminate any mechanical noise or interference often seen in high excursion cone designs.
Compound Radius Curve Pole Geometry: Alpine's Patented Compound Radius Curve pole geometry ensures a symmetrical magnetic field, while optimizing flux density to reduce distortion and further improve power handling and output.
Dual Voice Coils: For system flexibility, the woofer has two 2Ω voice coils. When the voice coils are wired in parallel, the woofer presents a 1Ω load; when wired in series, the woofer presents a 4Ω load.
Spring Terminals: The spring post terminals are all located on one side of the woofer. The terminals will accept bare wire up to 12-gauge, pin connectors, or single banana plugs.
Jumpers: Included with the woofer are two voice coil terminal jumpers, allowing you to easily wire the voice coils in parallel (for a 1Ω load) or series (for a 4Ω load).
Enclosure Compatibility
Sealed Box Volume: The recommended sealed box volume (gross) range is from 0.2 cubic feet to 0.5 cubic feet, with 0.3 cubic feet being the ideal size.
Ported Box Volume: The recommended ported box volume range is from 0.3 cubic feet to 0.75 cubic feet. The ideal size is 0.73 ft³ using a slot port measuring 8" (width) x 1" (height) x 17½" (length), resulting in a tuning frequency of 39 Hz.
The Alpine R2-W8D2 replaces these items:
- Kevlar reinforced pulp cone with HAMR Santoprene rubber surround
- power handling: 150-350 watts RMS
- frequency response: 30-200 Hz
Loading...
Loading accessories...
Customer Q&A
2 questions already asked
Loading...
Loading articles...
Speakers sound great. Better then expected
Travis from Columbus, OH