Contact us
Close contact box
Connect ID #
430 429 538 4
Connect ID #
430 429 538 4
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Rockford Fosgate Power T10001bd Mono subwoofer amp
500 watts RMS x 1 (New Stock)

Item # 575T1001BD

Massive, thundering Rockford Fosgate Power series amps — with their fine-tuned audio controls, extreme...

Find what Fits your vehicle


Checking fit...

Massive, thundering Rockford Fosgate Power series amps — with their fine-tuned audio controls, extreme...

Item # 575T1001BD

Shop all Rockford Fosgate Car Amplifiers

About the Rockford Fosgate Power T10001bd

Tim Sprinkle
Massive, thundering Rockford Fosgate Power series amps — with their fine-tuned audio controls, extreme durability, and proprietary technologies (like TRANS-ana circuitry for ultra-clean signal transfer and MEHSA for cool-running power) — are capable of stronger, more reliable performance than most other amplifiers on the market.

Want big bass? Look at our SubwoofersMassive, thundering Rockford Fosgate Power series amps — with their fine-tuned audio controls, extreme durability, and proprietary technologies (like TRANS-ana circuitry for ultra-clean signal transfer and MEHSA for cool-running power) — are capable of stronger, more reliable performance than most other amplifiers on the market.

If you're looking for a dedicated, bass-driving machine, say hello to the Power T10001bd! Equipped with Class bd technology (Rockford Fosgate's patented subwoofer amp design), this beast produces an amazing 75% efficiency rating with a highly stable output. Even under heavy loads, it will maintain steady power flow and a safe operating temperature, saving your music from clipping and distortion. The Power T10001bd operates safely at 1-ohm impedance, punching out an impressive 1,000 watts!

The variable low-pass filter with near-vertical 24 dB per octave slope lets you decide exactly which frequencies to send to your subs. Trigger a bass blast (up to 18 dB, variable from 35-70 Hz) with the dash-mountable remote. The Class bd design allows Rockford Fosgate to design this amp with a smaller footprint, giving you more installation options than you'll usually find in high-powered amps.


Product highlights:

  • 500 watts RMS x 1 at 4 ohms (750 watts RMS x 1 at 2 ohms)
  • 1000 watts RMS x 1 at 1 ohm (1-ohm stable)
  • frequency response 20-250 Hz
  • Class bd technology
  • CEA-2006 compliant
  • requires 1/0-gauge power and ground leads — wiring and hardware not included with amplifier
  • variable low-pass filter (32-250 Hz, 24 dB/octave)
  • Para-Punch bass EQ (0-18 dB with variable center frequency between 35-70 Hz) with wired remote control
  • MOSFET power supplies and outputs
  • MEHSA mounting technology increases the heat transfer from the MOSFET output devices to the heat sink, for higher power output, lower operating temperatures, and greater reliability.
  • TOPAZ noise-killing differential inputs eliminate 80% of ground loop noise between the head unit and the amp.
  • TRANS-ana circuitry keeps preamp signal clean
  • NOMAD advanced protection circuitry monitors temperature, voltage, current and impedence, and provides "intelligent" shut-down protection without limiting system performance.
  • fan cooled
  • preamp outputs for easy connection to a second amplifier
  • bd Sync terminal for connection to a second bd amplifier, to drive a common load
  • fuse rating: 150A x 1
  • dimensions: 17-15/16"W x 2-11/16"H x 12-3/4"D
  • warranty: 2 years
  • MFR # T10001bd

What's in the box:

  • Mono-block amplifier with removable terminal/control cover (attached by 2 Allen-head bolts)
  • 150-amp ANL fuse (installed)
  • 4.5mm Allen wrench
  • 4 Self-tapping screws (3/4" length)
  • 2 Terminal reducers (for power and ground wires)
  • Para-Punch Remote Bass Module
  • Module mounting clip
  • 2 Self-tapping screws for mounting module (length 7/16")
  • 16.25' Remote Bass Module cable (with male RJ-45 phone plugs on each end)
  • Performance Verification Certificate
  • Installation & Operation Manual (English/French/Spanish/German/Italian)

Customer reviews for Rockford Fosgate Power T10001bd

Loading reviews...

Average review:

4.5 out of 5 stars
7 reviews

Thanks for submitting your review

Filter by rating

Customer photos

Customer provided image, click to load a larger version.
Customer provided image, click to load a larger version.

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee review (What's this?)

Reviewed on

This review was collected as part of a promotion



Crutchfield response
Customer provided image, click to load a larger version.
<< >>

More details on the Rockford Fosgate Power T10001bd

Mark G.

Product Research

Inputs and Outputs Notes
Specifications Notes


Class BD Design: The Rockford Fosgate Power Series T10001bd is a Class BD design amp. Class BD gives you the super-efficient design of a Class D amp with the clarity and sound quality of a Class B amp. Rockford's patent-pending technology is called STARDUST, which is an acronym for Single-Terminal Alternating Rail Dual-Sampling Topology. The power supply of this Power bd amplifier is designed to be more than 75% efficient at all power levels. (Most Class AB amps are between 20% to 60% efficient.)

1-Ohm Stable: This amplifier is capable of accepting a speaker load down to 1-ohm or more. This allows you to obtain maximum power for multiple speaker configurations.

3-Stage Convection Cooling: The amp is cooled by a 3-stage thermal design that consists of a 3-speed variable fan, an integrated PCB plenum, and focused mass heat distribution utilizing a highly efficient cast aluminum heatsink. This superior design keeps the amp's internal components cool, maximizes the amp's potential, reduces distortion, and increases efficiency.

TOPAZ: TOPAZ, an acronym for Tracking Operation Pre-Amplifier Zone, is a patented circuit that eliminates ground loops by referencing signal ground from the first component in the chain (usually the source unit). About 80% of noise problems are created by ground loops. Eliminating ground loops results in a 30-40dB improvement of the isolation between input ground and chassis ground.

NOMAD: The amplifier utilizes an intelligent protection circuit called NOMAD (NOn-Multiplying Advanced Decision), which uses an analog computer to make real-time decisions regarding temperature, voltage, current, and impedance. The result is an amplifier with "intelligent" protection that will protect itself, but will not limit the performance of the amp.

DSM (Discrete Surface Mount): In the manufacturing process high speed robotics are used to place 0% tolerance resistors and large board traces providing greater reliability and efficiency.

Stealth Controls/Connections: All of the amplifier's connections and controls are located on the front panel. The cover conceals the wires for an ultra-clean installation, and is easily removable to give you access to the controls.

Built-in ANL Fuse: A 150-amp ANL fuse comes installed in the top panel of the amp under the removable cover. The fuse is easily accessible in case of failure.

Internal Crossover: The built-in 24dB/octave Butterworth low-pass filter features a variable crossover point from 32Hz to 250Hz. This crossover is always engaged; it cannot be turned off.

Infrasonic Filter: The infrasonic (or subsonic) filter is a 12dB/octave high-pass filter designed to prevent frequencies below 28 Hz from being applied to the subwoofer from the amplifier. When activated, the infrasonic filter eliminates super-low frequencies that are potentially damaging to the subwoofer and require tremendous amplifier power to reproduce. Consequently, the filter improves performance and power handling, especially with vented enclosures.

bd Sync: This amplifier has a 6-pin mini-DIN "bd Sync" connector on the front panel which allows you to link it with another bd amplifier for twice the power output. The two amps will need to be connected together with a bd Sync cable to allow the two independent frequency carrier generators in each unit to be synchronized. When driving a common load with two linked bd amplifiers, you will need to use the Phase Switch to phase one amplifier 180? from the other.

Mode Switch: The Power T10001bd can be configured to operate as a single amplifier, or connected to a series of other bd amplifiers in a daisy-chain. The 3-way Mode Switch lets you choose one of the following mode settings:

  • Single: the amplifier is being used as a single stand-alone unit
  • Master: the amplifier is the first amplifier in a series of amps, each driving its own load; the gain, crossover, infrasonic filter, and bass boost settings for this amp apply to all subsequent amps in the chain
  • Slave: the amplifier is daisy-chained to a Master amp, and uses the Master amp's settings

Para-Punch Remote Bass Module: The Para-Punch Remote Bass dual-control module helps overcome road noise and correct for acoustical deficiencies in the listening environment. The Para-Punch Bass control has a narrow band adjustment, variable from 0dB to +18dB with a Gyrator-based Punch EQ that eliminates frequency shift with boost. The other control is used for adjusting the center frequency, variable from 35Hz to 70Hz. Using the supplied mounting bracket, the module can be mounted in any convenient location under your vehicle's dash. You can also remove the cover and flush-mount the module in a 2" wide x 7/8" high cutout in the dash. With the cover, the remote bass module is 2.285" wide, 1.211" tall and 1.507" deep (1.99" including knobs).

LED Indicators: Three LEDs are located on the top panel of the amplifier to indicate the following:

  • Power: glows blue when the unit is turned on
  • Thermal: glows red if the amplifier reaches the third stage of thermal protection; the amp will shut down to cool when this occurs
  • Protect: glows yellow if a short circuit or too low of an impedance is detected at the speaker connections; the amp will automatically shut down if this occurs

Inputs and Outputs Notes

Power/Ground Terminals: The Power T10001bd features heavy-duty platinum-plated power and ground set-screw connectors that will accommodate up to 1/0-gauge bare wire. The connectors are angled downward to make it easier to conceal the wires under the removable cover. Wire reducers are supplied to allow you to securely install 4-gauge wire if necessary. A Phillips-head screwdriver (not supplied) is required to tighten/loosen the set screws.

Remote Turn-On Terminal: The amp provides a platinum-plated remote turn-on set-screw terminal for up to 12-gauge bare wire. A small Phillips-head screwdriver is required to tighten/loosen the set screw.

Speaker Terminals: The heavy-duty, nickel-plated Captive C-clamp wire connectors can accept bare wire sizes from 8-gauge to 18-gauge. Terminals are provided for two speakers (A + B). Both sets of terminals output a mono signal, and are internally wired in parallel. A Phillips-head or slotted screwdriver is required to tighten/loosen the terminals.

RCA Pass-Thru Jacks: The pass-thru jacks provide a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the amplifier location. The pass-thru jacks are not affected by the low-pass or infrasonic filters.

Remote Bass: A female RJ-45 phone jack is provided for connecting the cable for the supplied Para-Punch Remote Bass module.

bd Sync: A female 6-pin mini-DIN jack is provided for connecting this amp to another bd-series amp to drive a common load. This jack allows you to synchronize the frequency carrier generators of the two amps.

Specifications Notes

CEA-2006 Compliant: The specifications given by Rockford Fosgate for the Power T10001bd amplifier comply with the new CEA-2006 Amplifier Power Standard from the CEA (Consumer Electronics Association). All manufacturers who comply with the standard can display the CEA-2006 logo on their product.

Performance Verification Certificate: Each amplifier comes with a Performance Verification Certificate which lists the results of a 10-point performance inspection and lists the amplifier's measured power output. The measured power output typically exceeds the amp's rated power.

Rated Power Specifications (at 14.4 volts):

  • Total Power at 4 ohms: 500 watts
  • Total Power at 2 ohms: 750 watts
  • Total Power at 1 ohm: 1000 watts

Loading accessories...

Customer Q&A

Loading articles...

Compare the sound