About the Sound Ordnance™ M100-2

Give your music some firepower
Give your music some firepower
Your vehicle's interior is like an audio battlefield with your music fighting to get heard over the noises of the wind and road. Sound Ordnance's M100-2 2-channel amplifier can provide 110 watts RMS to each channel — more than enough power to overcome all the sonic enemies of clean, loud music.
Versatility
You can bridge the M100-2 for 1-channel operation to run a subwoofer with 200 watts RMS. A low-pass filter and adjustable bass boost allow you to control the bass tone at will. For your full-range speakers, an adjustable high-pass filter makes sure they operate within their optimum range and give you the best tone possible.
Rugged and compact
This amp's tiny size lets you fit it almost anywhere in a vehicle. Its tough construction, rugged looks, and 3-year warranty ensure you will enjoy the full power of your music for the long haul. Even better, you can add this Sound Ordnance amplifier to your arsenal at a great price.

This compact amp gives you all the controls you need to maximize performance in your system.
Product highlights:
- 2-channel car amplifier
- 110 watts RMS x 2 at 4 ohms (140 watts RMS x 2 at 2 ohms)
- 200 watts RMS x 1 bridged at 4 ohms (4-ohm stable bridged)
- Class D amp technology
- variable high- and low-pass filters (50-750 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 45 Hz)
- preamp inputs
- cooling fan
- fuse rating: 40A x 1
- 8-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 8-1/4"W x 2-1/16"H x 4-3/4"D
- warranty: 3 years
- MFR # M100-2
What's in the box:
Sound Ordnance™ M100-2 owner's manual
- 2-Channel amplifier
- 40-amp ATO blade fuse (installed)
- 3mm Allen wrench
- Four 3/8" Self-tapping screws
- 4 Split lock washers
- 4 Flat washers
- Owner's Manual
Reviews (57)
Customer reviews for Sound Ordnance™ M100-2
Loading reviews...
Average review:
4.5 out of 5 starsThanks for submitting your review
Customer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Sound Ordnance™ M100-2

Features & specs
Performance | ||
---|---|---|
RMS Power Output (Watts x Channels) |
110 x 2 | |
Peak Power Output (Watts x Channels) | 280 x 1 | |
Power at 2 Ohms (Watts x Channels) | 140 x 2 | |
Bridged Power (Watts x Channels) | 200 x 1 | |
Minimum Impedance Bridged | 4 | |
Minimum Impedance Unbridged | 2 | |
Minimum Impedance | 2 | |
Best Frequency Response | 20-20k Hz | |
THD at Rated RMS Power | 1% | |
Signal to Noise Ratio | 100 dB | |
Input Voltage | 13.6v | |
Features | ||
Amplifier Class | D | |
Low-Pass Crossover Frequency | 50-750 Hz | |
Low-Pass Slope (dB/octave) | 12 dB/oct | |
High-Pass Crossover Frequency | 50-750 Hz | |
High-Pass Slope (dB/octave) | 12 dB/oct | |
Bass Boost | 0-12 dB | |
Bass Boost Frequency | 45 Hz | |
Fan Cooled | Yes | |
Fuse Rating | 40 | |
Speaker Level Inputs | No | |
Preamp Outputs | No | |
Width (inches) | 8-1/4 | |
Height (inches) | 2-1/16 | |
Depth (inches) | 4-3/4 | |
Parts Warranty | 3 Years | |
Labor Warranty | 3 Years |
Product Research
Features
Power Ratings: The Sound Ordnance M100-2 is a 2-channel Class D amplifier with an RMS power rating of 110 watts per channel into 4 ohms, and 140 watts per channel into 2 ohms. The amp can also be bridged into a 4-ohm load for a power rating of 200 watts (x 1). Power ratings are measured with an input power of 13.6 volts.
Crossovers: The built-in crossover can be set to high-pass, low-pass, or full range. The crossover point is continuously variable from 50 to 750 Hz and the slope is 12dB per octave.
Bass Boost: The Bass EQ (bass boost) is continuously variable from 0 to +12 dB and is centered at 45 Hz.
LED Indicators: There are two LED indicators: a green LED that illuminates when the amp is powered on, and a red LED that illuminates when the amplifier is in protect mode due to overheating or a short circuit in the speaker wire.
Fan Cooled: A thermally-activated fan on the bottom of the amp helps cool the internal components.
Connections
Power Connections: The power and ground connections are set screw terminals that will accommodate up to 8-gauge wire. (An 8-gauge amplifier wiring kit is recommended.) The remote turn-on terminal is a set screw terminal that will also accept up to 8-gauge wire. A 3mm Allen wrench is required to tighten/loosen the terminals (included).
Speaker Connections: The speaker terminal can be removed from the amp, which makes connecting the speaker wires easier. The terminal is mounted to the chassis of the amp with two screws. Bare speaker wire, up to 12-gauge, is held in place by screw-clamps on the terminal. A flat blade screwdriver (not supplied) is required to tighten/loosen the screw-clamps.
Signal Inputs: The amplifier has a pair of stereo RCA inputs.
The Sound Ordnance™ M100-2 replaces these items
Loading accessories...
Customer Q&A
9 questions already asked
Loading articles...
Pair this amp with a set of infinity 6.5 components, clean plenty of gain even when the top Is down on the convertible! Definitely would recommend this amp!
Chris M from NJ