QSC MP-A40V Power amplifier - 800W total into 4 channels at 70V, 100V, and 4 or 8 ohms

Features

Overview: The QSC MP-A40V rack-mount, 4-channel amplifier is designed to provide a total of 400 watts of combined output power for each of the 2 pairs of output channels, for 4Ω, 8Ω, 70V, and 100V applications. Featuring Class-D topology, a switch mode power supply, Auto-standby, and active limiting and protection circuitry, the MP-A40V is the ideal solution for installed background music and paging applications.

FlexAmp: QSC's proprietary FlexAmp technology adds flexibility to your installed sound system by allowing each output channel to provide asymmetrical wattage amounts. This means with a total output power of 400 watts, one channel can be setup to deliver 100 watts while the other channel can deliver 300 watts, or any such combination. FlexAmp technology even lets you mix 4Ω or 8Ω connections on one channel with 70 or 100 volt operation on the other channel.

Inputs/Outputs: Four 3-pin Euroblock (Phoenix) connectors provide the input channels, with each containing a signal +, -, and Ground, for either balanced or unbalanced connections. Two 4-pin Euroblock connector provides the 4 output channels, with each terminal accepting up to 12AWG speaker wire. The output connector features two built-in attachment screws for securing the plug to the back of the amplifier, preventing accidental disconnection.

Input Indicators:

• Rear Panel: Each of the 4 input channels includes a rear-panel status LED that can display the following:
  • Green: A signal is present on that channel.
  • Orange: The input signal is near the clip point and the built-in Limiter circuit has been engaged to protect the output.
  • Red: Channel is in Protect mode. Possible short on the output channel or thermal shutdown do to overheating.
  • Off: Amp is in Standby mode.
• Front Panel: Front-panel channel-status and Power LEDs provide the following information:
  • Signal: Illuminates indicating a signal is present on that channel.
  • Limiter/Protect: Lights to indicate Protect mode, Mute, or Limiter is activated. Off indicates system is working nominally.
  • Power: Lights blue when unit is On, Amber when in Standby, and off when amp is powered completely off.

Input Level Adjustment: Each Input channel includes an Attenuation dial for adjusting the input signal level. Each dial has 11 attenuation levels ranging from 0 (+4dBu) to ∞ for total attenuation.

Output Configuration: Each of the MP-A40V's rear-panel inputs includes a 3-position DIP switch for selecting the type of output for each channel. Options include:

• 4Ω or 8Ω Selection
• 70V or 100V Selection
• HPF On/Off: When set to On, this applies an 80Hz high-pass filter to that output channel. This should always be set to On when using 70V or 100V full-range speakers.

Remote: The MP-A40V includes a rear-panel 5-pin Euroblock connector, providing two functions in one connector:

• Standby: Two Remote Standby contacts allow you to put the amp into and out of Standby mode from a remote location with an optional switch (not included). When the two pins are shorted together (i.e. making contact), the amp will go into Standby mode. Likewise, opening the contacts will take the amp out of Standby mode.
• Relay: The Remote Relay output provides a means to monitor the amplifier's operating condition with external equipment (not included).

Auto-Standby: The QSC amplifier will automatically go into Standby mode after 28 minutes with no signal input. When the signal returns, the amp will auto-ramp the signal back to its original level, avoiding an instantaneously loud signal.

Fan: The MP-A40V includes a built-in fan in the rear side-panel, providing forced air cooling through to the front air vent. Fan speed is thermally regulated.

Specifications:

• Channels: 4
• Channel Power (4Ω, 8Ω, 70, or 100V): 200W
• Typical Distortion (4-8Ω): < 0.01%
• Maximum Distortion (4-8Ω): < 1%
• Damping Factor: 100
• Amplifier Topology: Class-D
• Gain @ 8Ω: 30dB
• Input Impedance: > 10k, balanced or unbalanced
• Input Sensitivity: 1.23V (+4dBu)
• Frequency Response (8Ω): 20Hz - 20kHz (+/- 0.5dB)
• Maximum Input Level: 12.3V (+24dBu)
• Signal to Noise: >103dB
• Highpass Filter: 80Hz per channel, DIP selectable
• Input Connector: (4) 3-Pin Euroblock
• Output Connector: (2) 4-Pin Euroblock
• Remote Connector: (1) 5-Pin Euroblock
• Front-Panel Indicators: Power, signal (per channel), limit/mute/protect (per channel)
• Rear-Panel Indicators: Bi-colored LED for signal and limit/mute/protect
• Cooling: Regulated-fan forced-air cooling, rear/side-to-front flow
• AC Power Supply: Universal with PFC, 100-240VAC, 50/60Hz
• Dimensions: Width = 19.0", Height = 1.75", Depth = 16.50" (incl. power cord)
• Net Weight: 9.3 lbs.