Contact us
Close contact box
Connect ID #
658 704 038 4
Connect ID #
658 704 038 4
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Nathan B's 1995 Pontiac Trans Sport

Vehicles in the Customer Car Showroom are submitted by customers and fans, and edited by Crutchfield writing staff. You can find more of these articles on the Showroom main page.

1995 Pontiac Trans Sport

Items installed:

  • Pioneer DEH-P7700MP CD receiver with OEL animated display
  • Polk Audio db1240 12" 4-ohm Component Subwoofer Single Voice Coil
  • (3) JL Audio XA-BLKPW8-6 black 8 Gauge Power Wires - 6ft
  • (2) EFX 17-ft. Stereo RCA Patch Cables
  • (20 Ft) StreetWires 8 ga. Translucent Red Power Cable
  • Polk Audio db461p 4"x6" plate 2-way car speakers - Front Dash
  • Pioneer TS-A1702C A-Series 6-1/2 Component Speaker System - Rear Lift Gate
  • Dual XPA2500 2-channel car amplifier - 50 watts RMS x 2 Powering the Rear Speakers
  • Sony 2/1-Channel Xplod XM-GTX1852 400 watts x 1 RMS at 4 ohms Powering the Subwoofer
  • Sony XM-235I 35 watts x 2 RMS Powering the Front Speakers
  • Pioneer Premier DEH-P7700MP in-Dash CD receiver with OEL display
  • Scosche 6 gauge single amplifier wiring kit
  • Power distribution block

Installation Description

I've always wanted to do a system in my vehicle. I had the head unit and 2 amplifiers already. My older brother had a sub box, head unit and amp installed at a shop and got charged WAY too much (my own opinion) and thought "I can do that myself better and cheaper." Maybe it's just the sibling rivalry thing.

So I got on your website ordered some parts and off I went. Built the sealed sub box myself per your instructions, fabricated a mounting board using the leftover MDF and some 2x4's and carpeted it all. For some reason one of my old amps didn't work so I had to run out and get me a new one. I wasn't going for massive boom, I just wanted to get clear accurate controlled sound, and boy did I get it! I'm more of a computer guy, so it took me a bit to do all the actual laborious stuff, but I'm VERY pleased with the finished job and have the pride that I did it myself (with some help from you guys) lol! Thank you!

Q&A Section

Why did you decide to upgrade your A/V system?

To compete with my older brother's system lol

What's the first thing you show people about your installation?

The use of space. I have the system where the rearseats were. So I have room for tools and groceries if needed

Why did you choose these products?

I have always LOVED the sound that Polk Audio produces, nice accurate and tight

What was the most difficult part of the installation?

Running the wires. My van has ALOT of trim and panels. Trying to work around, over and under all that was a real pain

What plans, if any, do you have for future upgrades?

Maybe upgrade the rear speakers to Polk's 6-3/4" components, just to keep all the speakers the same. Possibly different head unit

Sony stereo My Pioneer DEH-P7700MP at night
test fit Test fitting the box and mounting board
loaded box Polk Audio subwoofer loaded in the box
finished board The finished mounting board and subwoofer box
gear in the van Subwoofer and amps in the van
me in the van Me in the van (it was at night, so I had to brighten the pic)

Editor's note: Nathan's planning and attention to detail yielded an installation that looks incredible, and still leaves him with the cargo space he wants in a van. Nice job Nathan.

Return to the Customer Car Showroom.

Compare the sound