About the Clarion XC2110
Compact bass powerhouse
Compact bass powerhouse
Clarion's XC2110 mono subwoofer amplifier delivers up to 300 watts RMS from a chassis that's about the size of your hand. This micro-sized amp can fit almost anywhere, even behind many dashboards. And Clarion managed to pack more watts per square inch inside this little powerhouse than most other mono amps on the market.
Ready for outdoor work
The XC2110's circuits are coated on both sides for protection, so this amp is a great candidate for use in ATVs, boats, and other challenging applications. Clarion nickel-plated all the connectors to resist corrosion and ensure electrical flow, even during harsh conditions.
The XC2110's input circuitry resists the electronic noise common in cars, so you will enjoy clean, distortion-free bass. Soft turn-on and turn-off circuitry prevents potentially damaging thumps to your system as it powers on or off. A variable low-pass filter eliminates the sounds that your subwoofers can't reproduce, and a bass boost lets you emphasize the low-end thump. You'll also appreciate the high-level inputs, so you can hook this amp up to almost any system, even factory radios without RCA connections.
- mono subwoofer amplifier
- 200 watts RMS x 1 at 4 ohms (300 watts RMS x 1 at 2 ohms)
- CEA-2006 compliant
- Class D amp technology
- double-sided conformal-coated circuit board — suitable for power sports and marine applications (not waterproof)
- corrosion-resistant nickel-coated connections
- built-in ground loop isolation circuitry reduces input noise
- variable low-pass filter (35-250 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 50 Hz)
- preamp and speaker-level inputs
- 10-gauge power and ground leads recommended wiring and hardware not included with amplifier
- fuse rating: 40A x 1
- dimensions: 8-13/16"W x 1-5/8"H x 3-1/4"D
- warranty: 1 year
- MFR # XC2110
What's in the box:
- Mono subwoofer amplifier
- 40-amp ATO fuse (installed in-line)
- 9" Power/Ground harness
- 9" Speaker-level output harness
- Four 3/4" Self-tapping screws
- 4 Flat washers
- Owner's manual (English/ French/ Spanish)
- Warranty information
Customer reviews for Clarion XC2110
Average review:5.0 out of 5 stars
Thanks for submitting your review
More details on the Clarion XC2110
Features & specs
|RMS Power Output (Watts x Channels)||
200 x 1 |
|Peak Power Output (Watts x Channels)||400 x 1|
|Power at 2 Ohms (Watts x Channels)||300 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||20-250 Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||70 dB|
|Low-Pass Crossover Frequency||35-250 Hz|
|Low-Pass Slope (dB/octave)||12 dB/octave|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0-12 dB|
|Bass Boost Frequency||50 Hz|
|Speaker Level Inputs||Yes|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
RCA Inputs: One pair of female RCA line level inputs (left and right) are attached to the left end of the amp with 7" wires.
Speaker Level Inputs: The 8" speaker level input wires are also attached to the left end of the amp.
Crossover: The built-in low pass crossover is continuously variable from 35 Hz to 250 Hz and the slope is 12 dB/octave. Because this is a subwoofer amp, the crossover is always engaged and it cannot be used full range.
Gain: The rotary gain control is continuously variable; the range depends on which input you're using:
- RCA: 200mV to 8V
- Speaker Level: 600mV to 20V
Bass Boost: The bass boost is continuously variable from 0 to +12 dB and centered at 50 Hz, allowing you to dial in the amount of bass according to your personal preference.
Power Harness: The included power harness plugs into a pigtail harness attached to the amp, for a total of 18" power and ground wires. The power wire should be connected directly to the battery, so it will likely need to be extended using a 10-gauge or larger wire (the attached power and ground wires are both 12-gauge). An in-line fuse holder on the power wire holds the included 40-amp ATO style fuse and another in-line fuse should be added close to the battery.
Speaker Output Harness: The included speaker output harness plugs into a pigtail harness attached to the amp, for a total of 18" speaker wires. The remote turn-on wire is also in the speaker output harness.
5 questions already asked