Skip to main content
Chat
Photo of Expert Advisor Cam
Contact us

Expert help from our Advisors

What is an expert Advisor?
Connect ID #
985 902 205 5
Connect ID #
985 902 205 5
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Crown XTi 1002 Power amplifier — 275W x 2 at 8 ohms, 1,400W x 1 at 4 ohms bridged

Item # 859XTI1002

Crown's XTi 2 Series power amplifiers don't just make your speakers sing — they serve as vital lynchpins for...

Crown's XTi 2 Series power amplifiers don't just make your speakers sing — they serve as vital lynchpins for...

Item # 859XTI1002

Every order includes

  • Free lifetime tech support
  • 60-day price-drop protection
  • 60-day returns
In stock
$799.00

Other options

Get questions answered fast & free

Expert help 400+ hours training Virginia-based

About the Crown XTi 1002

Dominic DeVito

Product highlights:

    General Information:
    • 2-channel power amplifier with built-in digital signal processing
    • power output:
      • 275 watts per channel at 8 ohms
      • 500 watts per channel at 4 ohms
      • 700 watts per channel at 2 ohms
      • 1000 watts (mono) at 8 ohms in bridged mode
      • 1400 watts (mono) at 4 ohms in bridged mode
    • frequency response: 20-20,000 Hz (-1 dB)
    • signal-to-noise ratio: 100 dB
    • total harmonic distortion: 0.5% (20-20,000 Hz)
    Features:
    • independent right- and left-channel level controls
    • LCD screen with sel/prev/next buttons
    • digital signal processing:
      • defeatable Peakx Plus Limiters for each channel
      • input EQ: 6 parametric filters per channel
      • high-pass and low-pass crossover filters
      • output EQ: 8 parametric filters per channel
      • 50 ms of total delay
      • SubHarmonic Synth
    • proportional speed fan with front-to-rear airflow and three user-defined settings
    • initial power, DC voltage, short circuit, thermal, and current limiting protection
    • front-panel LEDs indicate power, signal, -10dB and -20dB below clipping, ready, clipping, and temperature
    • integrated cast aluminum handles
    Connections:
    • inputs: balanced XLR
    • outputs: binding posts and Neutrik Speakon
    • XLR Link/Out outputs to send signal to another amp
    • USB connection for HiQnet applications
    Other Information:
    • weight: 18.5 lbs.
    • 19"W x 3-1/2"H x 12-1/4"D (2 rack spaces)
    • warranty: 6 years (3 years if purchased before 1/1/20)
    • MFR # XTI1002
    • Item # 859XTI1002
    • California customers: Please click here for your Proposition 65 WARNING.

    More details on the Crown XTi 1002

    Russ B.

    Features & specs

    General
    Number of Channels 2
    Power Class ---
    Watts per channel 8 ohms 275
    Watts per channel 4 ohms 500
    Watts per channel 2 ohms 700
    Watts bridged 1000
    Fan cooled Y
    DSP Y
    Filters LPF, HPF
    Rack spaces 2
    Height (inches) 3-1/2
    Depth (inches) 12-1/4
    Width (inches) 19
    Weight 18.5 lbs
    Inputs
    RCA ---
    1/4" ---
    XLR 2
    Outputs
    1/4" ---
    Binding post 2
    Spring post ---

    Product Research

    Features

    Amplifier Presets: The Crown XTi2 Series amplifier comes pre-loaded with presets that makes it easy to configure the amplifier for your type of applications.

    • Stereo DSP Off (Preset 1): This is the default mode the amplifier is set to from the factory. The amplifier is configured for stereo mode with all processing disabled.
    • Bridge (Preset 2): Putting the amplifier in Bridge (bridge-mono) mode delivers the power of both amp channels into a single 8 or 4 ohm load.
    • Xover (Preset 3): Putting the amplifier in Xover mode enables a 1.2kHz 4th order (24dB/octave) filter that sends frequencies of 1.2kHz and below to Channel 1 output and frequencies of 1.2kHz and above to Channel 2 output.
    • BRG SUBS (Preset 4): Putting the amplifier in BRG SUBS (bridged subs) mode allows you to bridge the amplifier for use with a single 8 or 4 ohm subwoofer. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) LowPass filter is enabled, and the output mode is put into bridge-mono mode.
    • SUBSYNTH (Preset 5): Putting the amplifier in SUBSYNTH mode allows you to turn on the SubHarmonic Synth feature for use with a subwoofer on both channels. The inputs are automatically summed, a 90Hz 4th order (24dB/octave) filter is enabled on both Channel 1 and Channel 2, and the SubHarmonic Synth feature is turned on at +12dB level.

    Power Rating: Maximum average power in watts at 0.5% THD, 1 kHz.

    Impedance Load Dual Mode (stereo) Bridged Mode (mono)
    Wattage Wattage
    2 ohm 700 watts N/A
    4 ohm 500 watts 1,400 watts
    8 ohm 275 watts 1,000 watts

    Peakx Limiters: Peakx Limiters provide the ultimate in performance and protection for your entire system. This advanced algorithm was specifically developed and tuned to work with this amplifier and power-supply to achieve higher SPL will less audible artifacts. This means less distortion, less shutdowns, and maximum safe power delivered to your speakers. The Peakx Limiters can be easily turned on or off by channel right from the front panel eliminating the need to be digging around in the back of the dark rack.

    XLR Inputs/Outputs: The XTi2 Series amplifier provides two 3-pin XLR input connectors (one per channel). Two 3-pin XLR output connectors are provided (one per channel) to loop-thru signal from one amp to another.

    Outputs: The XTi2 Series amp feature two 4-Pole Speakon output connectors that will accept 2-pole or 4-pole Speakon connectors. The Channel 1 Speakon connector is wired for both channels so it can be used for bridged-mono wiring or for stereo wiring of two speakers to a single Speakon connector. There is also one pair of binding posts per channel that will accept banana plugs or bare wire.

    HiQnet USB Connector: The power amp's USB (type-B) port allows you to connect the amplifier to a computer for use with System Architect and Band Manager software (not included). The System Architect Software is required to have full control over all integrated processing features which can be downloaded from the following URL - http://hiqnet.harmanpro.com/. When controlling more than one XTi2 at a time you will need USB Hub. We recommend using a powered USB Hub.

    Adjustable Fan Speeds: The XTi2 Series amplifiers employ flow-through, front-to-back ventilation and internal fans with forced-air cooling for rapid, uniform heat dissipation. You can tailor the fan speed to specific applications. The default mode is NORMAL and should work fine for most applications. EARLY mode turns the fan on sooner at a "lower" temperature, and FULL-SPEED mode turns the fan on full-speed full-time. Full-speed mode is not recommended for "dirty" environments.

    LED Indicators: The power amplifier features ten LEDs (five for each output channel) to indicate status of amplifier.

    • Ready Indicator: Two green LEDs, one for each channel, illuminate when the amplifier is ready to produce audio.
    • Single Presence: Two green LED's, one for each channel, illuminate when the channel input signal exceeds -40dBu.
    • -10: Green LED flashes when output signal level exceeds -10dB below clip.
    • -20: Green LED flashes when output signal level exceeds -20dB below clip.
    • Clip: Two red LED's, one for each channel, illuminate when the channel's output is being overdriven.
    • Thermal: Two red LED's, one for each channel, illuminate when thermal compression begins.

    Loading accessories...

    Customer Q&A

    2 questions already asked

    Q
    rackmount ears removable?
    francois  Apr 25, 2022
    1 answer
    A
    No. They are integrated.
    jenny  Apr 28, 2022 (Staff)
    Q
    can this Crown XTi 1002 be set at 65hz crossover with a 100hz lowpass and a 20hz highpass useing the supplyed software ?
    john  Jun 05, 2017
    2 answers
    A
    Meant to say above '...using the supplied Software'.
    john  Jun 10, 2017
    A
    Yes, you can indeed have a 20 Hz highpass and a 100 Hz lowpass using the supplied crossover, all you need is a laptop or PC and a sufficient length of USB (2.0) cable to reach your listening position and you can set it all up by ear if you want...the free software is downloaded from Crown's website. Frequency selections can be made on the order of 1/1000th of a dB, so very precise control is on tap wherever from 20 Hz to 20 kHz you choose. Offers 1st through 5th order slopes, the 4th and 5th order slopes are available as either Butterworth or LR. Adjustable polarity in the digital domain for each channel. All the digital controls can be adjusted on the fly. Very good sound quality, btw.
    john  Jun 10, 2017

    Loading articles...

    Looking for more?

    Check out the next model in this lineup.


    Adding...

    Get more power

    The Crown XTi 2002 offers up to 800 watts at 4 ohms
    Compare the sound